From: Szabolcs Sipos Date: Tue, 25 Jun 2013 13:21:53 +0200 Subject: [U-Boot] Save flash from U-Boot Message-ID: <000301ce7196$32f25b20$98d71160$@balfug.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de I have a ZTE ZXV10 H201L, and want to back its flash up for future recovery and for getting the VOIP settings. Since the firmware is modified by the ISP, I have no access to it. It has U-Boot (with serial console) but some commands are missing: =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.24 17:35:15 =~=~=~=~=~=~=~=~=~=~=~= ROM VER: 1.? ROM VER: 1.1.3 CFG 01 DDR Access auto data-eye tuning Rev 0.3c DDR size from 0xa0000000 - 0xa1ffffff DDR check ok... start booting... ZTE U-Boot V1.0.09 (Sep 9 2011 - 11:28:12) Boot from NOR flash AR9 BOARD CLOCK CPU 333M RAM 166M DRAM: 32 MB relocate_code start relocate_code finish. Flash: 8 MB *** Warning - bad CRC, using default environment parse tag param success In: serial Out: serial Err: serial Net: switch chip id=0000c852!! amazon_s Switch Type run flash_nfs to mount root filesystem over NFS *** Press 1 means entering boot mode*** ***Press 2 means entering testing mode*** ***Press 3 means entering norm mode*** Hit key to stop autoboot: 3  2  0 Entering boot mode ... AMAZON_S # ? ? - alias for 'help' askenv - get environment variables from stdin autoscr - run script from memory base - print or set address offset bdinfo - print Board Info structure bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console erase - erase FLASH memory flinfo - print FLASH memory information go - start application at address 'addr' help - print online help httpd - start http server imls - list all images found in flash loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nm - memory modify (constant address) printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable setenv - set environment variables SPI flash sub-systemsflash - SPI FLASH sub-system sleep - delay execution for some time tag - set or get or list tag parmeters version - print monitor version AMAZON_S # base Base Address: 0x00000000 AMAZON_S # bdinfo boot_params = 0x81DDEFB0 memstart = 0x80000000 memsize = 0x02000000 flashstart = 0xB0000000 flashsize = 0x00800000 flashoffset = 0x00000000 ethaddr = (a mac addr) ip_addr = 192.168.1.254 baudrate = 115200 bps AMAZON_S # printenv bootcmd=run flash_flash bootdelay=3 baudrate=115200 preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo serverip=192.168.1.55 netdev=eth0 baudrate=115200 rootpath=/opt/nfs nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):on mem=32M vpe0mem=30M vpe1mem=2M vpe1_load_addr=0x81e00000 addmisc=setenv bootargs $(bootargs) console=ttyS1,$(baudrate) ethaddr=$(ethaddr) phym=$(mem) mem=$(vpe0mem) panic=1 vpe1_load_addr=$(vpe1_load_addr) vpe1_mem=$(vpe1mem) vpe1_wired_tlb_entries=1 flash_nfs=run nfsargs addip addmisc;bootm $(kernel_addr) ramdisk_addr=B0100000 flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr) img_uboot=u-boot.ifx net_nfs=tftp 80500000 $(img_kernel);run nfsargs addip addmisc;bootm net_ram=tftp 80500000 $(img_kernel);run ramargs addip addmisc;bootm load=tftp 80500000 $(img_uboot) flash_flash=run addip addmisc; bootm $(kernel_addr) f_ubootconfig_addr=0xB001A000 f_ubootconfig_size=0x1000 ethaddr=(a mac addr) ipaddr=192.168.1.254 netmask=255.255.255.0 stdin=serial stdout=serial stderr=serial ethact=amazon_s Switch Environment size: 1254/4092 bytes AMAZON_S # =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.24 17:35:15 =~=~=~=~=~=~=~=~=~=~=~= As I know cp can copy from TFTP to flash. Is it possible backward? If it cannot be solved through serial port, I may use JTAG. I just want to do it as simply as possible.