From: "Ricardo Chamorro" Date: Tue, 12 Jul 2005 01:38:56 +0000 Subject: [LARTC] Several basic doubts Message-Id: <000801c58682$899e4a90$026fa8c0@ricardo> MIME-Version: 1 Content-Type: multipart/mixed; boundary="===============0137418240==" List-Id: To: lartc@vger.kernel.org This is a multi-part message in MIME format. --===============0137418240== Content-Type: multipart/alternative; boundary="----=_NextPart_000_0005_01C58669.52C557C0" This is a multi-part message in MIME format. ------=_NextPart_000_0005_01C58669.52C557C0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable I have a connection cablemodem (down 1024kbit up 256 kbit) that spreads = Internet to a LAN of 4 PC. Router-firewall is one 486 DX4 100 96 MB RAM = that runs a Debian Sarge (kernel 2,4,25), that does NOT serve nor squid, = nor samba, nor smtp, etc.... single do routing-firewalling. =20 I am something confused by opinions and "presumed" manual and howto that = I have read and have confused I more... Then I ask to them you: =20 I must do shaping with the NIC that connect with ISP (etho)... or with = the NIC of the LAN (eth1)????... Because I have seen opinions on both = possibilities, but I have tested the two and second did not give me good = results. In the case of using the NIC to Internet (eth0) I must set = like CEIL the bandwidth of downstream (1024kbit) or upstream = (256kbit)????... And in such case I must set the 75 percent = approximately of the bandwidth to avoid to saturate the band? =20 Another question is if it agrees -upon my case- using priorities for the = classes... Thanks in advance Ricardo ------=_NextPart_000_0005_01C58669.52C557C0 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable
I have a connection cablemodem (down = 1024kbit up=20 256 kbit) that spreads Internet to a LAN of 4 PC.  Router-firewall = is one=20 486 DX4 100 96 MB RAM that runs a Debian Sarge (kernel 2,4,25), that = does NOT=20 serve nor squid, nor samba, nor smtp, etc.... single=20 do routing-firewalling. 
I am something confused by opinions and = "presumed"=20 manual and howto that I have read and have confused I more...  Then = I ask=20 to them you: 
I must do shaping with the NIC that = connect with=20 ISP (etho)...  or with the NIC of the LAN (eth1)????...  = Because I=20 have seen opinions on both possibilities, but I have tested the two and = second=20 did not give me good results.  In the case of using the NIC to = Internet (eth0) I must set like CEIL the bandwidth of downstream = (1024kbit) or=20 upstream (256kbit)????...  And in such case I must set the 75 = percent=20 approximately of the bandwidth to avoid to saturate the band? =20
Another question is if it agrees -upon = my=20 case- using priorities for the classes...
Thanks in advance
Ricardo
------=_NextPart_000_0005_01C58669.52C557C0-- --===============0137418240== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc --===============0137418240==--