From: Nicolas Meaux Date: Sat, 21 Mar 2020 19:57:01 +0100 Subject: bootp problems with rpi4 Message-ID: <0a75c7bf-e73c-2367-12c6-25fb40a09e22@gmail.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hello, I use u-boot for raspberry, but i have a different behavior between rpi3b and rpi4b. * i use the same u-boot source files (2020.04-rc3-00161-g14eb12a3c8) * i use the same method for compiling ( make -j4 ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- all ) * i use the same dhcp/tftp server in both case . * i just load a different config :? rpi_3_defconfig & rpi_4_defconfig When i boot with my rpi3b, it happens the following : * 1st bootp ok * tftp download boot.scr.uimg file * 2nd bootp ok * tftp load the "bootfile filename" setup in the dhcp config which is an efi application * efi application is loaded and the rest of the boot process is fine. When i boot with my rpi4b, it happens the following : * 1st bootp ok * tftp download boot.scr.uimg file * 2nd bootp nok and goes into timeout, with a tcpdump on the ethernet interface connected to the pi, absolutely 0 bootp requested are made by u-boot at this step. ***** U-boot log with rpi3b : U-Boot 2020.04-rc3-00161-g14eb12a3c8 (Mar 21 2020 - 18:41:52 +0100) DRAM:? 948 MiB RPI 3 Model B (0xa02082) MMC:?? mmc at 7e202000: 0, sdhci at 7e300000: 1 Loading Environment from FAT... WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! Card did not respond to voltage select! In:??? serial Out:?? vidconsole Err:?? vidconsole Net:?? No ethernet found. starting USB... Bus usb at 7e980000: scanning bus usb at 7e980000 for devices... 3 USB Device(s) found ?????? scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot:? 0 WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! Card did not respond to voltage select! Card did not respond to voltage select! Device 0: unknown device Waiting for Ethernet connection... done. BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 10.0.0.3 (2245 ms) Using smsc95xx_eth device TFTP from server 10.0.0.254; our IP address is 10.0.0.3 Filename 'boot.scr.uimg'. Load address: 0x2400000 Loading: ################################################## 322 Bytes ???????? 34.2 KiB/s done Bytes transferred = 322 (142 hex) ## Executing script at 02400000 WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! Card did not respond to voltage select! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! Card did not respond to voltage select! Bad Linux ARM64 Image magic! Waiting for Ethernet connection... done. BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 *** Unhandled DHCP Option in OFFER/ACK: 60 *** Unhandled DHCP Option in OFFER/ACK: 60 DHCP client bound to address 10.0.0.3 (2195 ms) Using smsc95xx_eth device TFTP from server 10.0.0.254; our IP address is 10.0.0.3 Filename 'snp.efi'. Load address: 0x1000000 Loading: ################################################## 162.7 KiB ???????? 2.4 MiB/s done Bytes transferred = 166624 (28ae0 hex) Waiting for Ethernet connection... done. Using smsc95xx_eth device TFTP from server 10.0.0.254; our IP address is 10.0.0.3 Filename 'dtb/broadcom/bcm2837-rpi-3-b.dtb'. Load address: 0x2600000 Loading: ################################################## 19.1 KiB ???????? 83 KiB/s done Bytes transferred = 19530 (4c4a hex) WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! WARNING at drivers/mmc/bcm2835_sdhost.c:411/bcm2835_send_command()! Card did not respond to voltage select! Scanning disk mmc at 7e202000.blk... Disk mmc at 7e202000.blk not ready Card did not respond to voltage select! Scanning disk sdhci at 7e300000.blk... Disk sdhci at 7e300000.blk not ready Found 0 disks efi_load_pe: Invalid DOS Signature iPXE initialising devices...ok iPXE 1.20.1+ (g18dc) -- Open Source Network Boot Firmware -- http://ipxe.org ***** U-boot log with rpi4b : U-Boot 2020.04-rc3-00161-g14eb12a3c8 (Mar 19 2020 - 22:02:29 +0000) DRAM:? 1.9 GiB RPI 4 Model B (0xb03111) MMC:?? emmc2 at 7e340000: 0, mmcnr at 7e300000: 1 Loading Environment from FAT... Card did not respond to voltage select! In:??? serial Out:?? serial Err:?? serial Net:?? eth0: genet at 7d580000 Hit any key to stop autoboot:? 0 Card did not respond to voltage select! Card did not respond to voltage select! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 10.0.0.4 (2010 ms) Using genet at 7d580000 device TFTP from server 10.0.0.254; our IP address is 10.0.0.4 Filename 'boot.scr.uimg'. Load address: 0x2400000 Loading: # ???????? 332 KiB/s done Bytes transferred = 340 (154 hex) ## Executing script at 02400000 Card did not respond to voltage select! Scanning disk emmc2 at 7e340000.blk... Disk emmc2 at 7e340000.blk not ready Card did not respond to voltage select! Scanning disk mmcnr at 7e300000.blk... Disk mmcnr at 7e300000.blk not ready Found 0 disks efi_load_pe: Invalid DOS Signature Card did not respond to voltage select! Card did not respond to voltage select! Bad Linux ARM64 Image magic! BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17 Retry time exceeded; starting again U-Boot> Thx in advance for any help. Rgds, Nicolas