From: derkling@gmail.com (Patrick Bellasi) Date: Mon, 30 Nov 2009 10:48:05 +0100 Subject: [PATCH 2/3] [AT91] Add support for the Daricom C3-Ax03 board In-Reply-To: <1259574486-13391-2-git-send-email-derkling@gmail.com> References: <20091129234917.GB18841@game.jcrosoft.org> <1259574486-13391-1-git-send-email-derkling@gmail.com> <1259574486-13391-2-git-send-email-derkling@gmail.com> Message-ID: <1259574486-13391-3-git-send-email-derkling@gmail.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Add initial support for the Daricom C3-Ax03 board. Signed-off-by: Patrick Bellasi +config MACH_C3AX03 + bool "Daricom C3-Ax03 board" + help + Select this if you are using the Daricom C3-Ax03 Ex Telemetry Device. + + endif # ---------------------------------------------------------- diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index ada440a..4f74746 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o obj-$(CONFIG_MACH_AFEB9260) += board-afeb-9260v1.o obj-$(CONFIG_MACH_CPU9260) += board-cpu9krea.o +obj-$(CONFIG_MACH_C3AX03) += board-c3ax03.o # AT91SAM9261 board-specific support obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o diff --git a/arch/arm/mach-at91/board-c3ax03.c b/arch/arm/mach-at91/board-c3ax03.c new file mode 100644 index 0000000..b172233 --- /dev/null +++ b/arch/arm/mach-at91/board-c3ax03.c @@ -0,0 +1,364 @@ +/* + * linux/arch/arm/mach-at91/board-c3ax03.c + * + * Adapted from various board files in arch/arm/mach-at91 + * + * Copyright (C) 2009-2010 Patrick Bellasi (derkling at gmail.com) + * Copyright (C) 2009-2010 Daricom srl (www.daricom.it) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include +#include + +#include +#include +#include +#include + +#include "sam9_smc.h" +#include "generic.h" + +static void __init c3ax03_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART2 on ttyS3. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); + + /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init c3ax03_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata c3ax03_usbh_data = { + .ports = 1, /* PQFP version of AT91SAM9260 */ +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata c3ax03_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 1, /* using external pull-up */ +}; + +/* +* I2C +*/ +static struct pca953x_platform_data c3ax03_gpio_ext_pdata_0 = { + .gpio_base = 0, /* PCA9555 */ +}; + +static struct i2c_board_info __initdata c3ax03_i2c_devices[] = { + { /* PCA9555: 16-bit I2C-bus and SMBus I/O port with interrupt */ + I2C_BOARD_INFO("pca9555", 0x27), + .platform_data = &c3ax03_gpio_ext_pdata_0, + }, +}; + +/* + * NAND devices + */ +static struct mtd_partition __initdata c3ax03_nand_partitions[] = { + { /* 16 KB */ + .name = "AT91Bootstrap", + .offset = 0, + .size = 16 * 1024, + }, + { /* 16 KB, offset 0x4000 */ + .name = "UBoot-env", + .offset = MTDPART_OFS_NXTBLK, + .size = 16 * 1024, + }, + { + /* 224 KB, offset 0x8000 */ + .name = "UBoot", + .offset = MTDPART_OFS_NXTBLK, + .size = 224 * 1024, + }, + { /* 2048 KB, offset 0x40000 */ + .name = "Kernel", + .offset = MTDPART_OFS_NXTBLK, + .size = 2048 * 1024, + }, + { /* Up to flash size (default 32MB), offset 0x240000 */ + .name = "Filesystem", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL, + } +}; + +static struct mtd_partition * __init c3ax03_nand_partinfo(int size, int + *num_partitions) +{ + *num_partitions = ARRAY_SIZE(c3ax03_nand_partitions); + return c3ax03_nand_partitions; +} + +static struct atmel_nand_data __initdata c3ax03_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = c3ax03_nand_partinfo, + .bus_width_16 = 0, +}; + +static struct sam9_smc_config __initdata c3ax03_nand_smc_config = { + .ncs_read_setup = 0, + .nrd_setup = 1, + .ncs_write_setup = 0, + .nwe_setup = 1, + + .ncs_read_pulse = 3, + .nrd_pulse = 3, + .ncs_write_pulse = 3, + .nwe_pulse = 3, + + .read_cycle = 5, + .write_cycle = 5, + + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | + AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, + + .tdf_cycles = 2, +}; + +static void __init c3ax03_add_device_nand(void) +{ + + /* configure chip-select 3 (PC14) */ + sam9_smc_configure(3, &c3ax03_nand_smc_config); + + at91_add_device_nand(&c3ax03_nand_data); +} + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata c3ax03_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 0, + .use_twi_pins = 0, +}; + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata c3ax03_mmc_data = { + .slot_b = 1, + .wire4 = 1, +}; + +/* + * LEDs + */ +static struct gpio_led c3ax03_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "led:cpu", + .gpio = AT91_PIN_PB18, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "led:heartbeat", + .gpio = AT91_PIN_PB19, + .default_trigger = "heartbeat", + } +}; + +/* + * GPIOs + */ +static struct gpio_keys_button c3ax03_buttons[] = { + { + .gpio = AT91_PIN_PC0, /*PA9*/ + .code = 0x00, + .desc = "Battery Power", + .active_low = 1, + .wakeup = 0, + }, + { + .gpio = AT91_PIN_PC13, /*PB13*/ + .code = 0x01, + .desc = "OdoCanGps Intr", + .active_low = 1, + .wakeup = 1, + }, + { + .gpio = AT91_PIN_PC15, /*PC15*/ + .code = 0x02, + .desc = "Digital Intr", + .active_low = 1, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data c3ax03_button_data = { + .buttons = c3ax03_buttons, + .nbuttons = ARRAY_SIZE(c3ax03_buttons), +}; + +static struct platform_device c3ax03_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &c3ax03_button_data, + } +}; + +static void __init c3ax03_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PC0, 1); + at91_set_deglitch(AT91_PIN_PC0, 1); + + at91_set_gpio_input(AT91_PIN_PC13, 1); + at91_set_deglitch(AT91_PIN_PC13, 1); + + at91_set_gpio_input(AT91_PIN_PC15, 1); + at91_set_deglitch(AT91_PIN_PC15, 1); + + platform_device_register(&c3ax03_button_device); + +}; + +static void __init c3ax03_init_gpio(void) +{ + + /* USART2 (ttyS3) Multiplexer */ + gpio_request(AT91_PIN_PB16, "ttyS3_mux0"); + gpio_request(AT91_PIN_PB17, "ttyS3_mux1"); + gpio_direction_output(AT91_PIN_PB16, 0); + gpio_direction_output(AT91_PIN_PB17, 0); + gpio_export(AT91_PIN_PB16, false); + gpio_export(AT91_PIN_PB17, false); + + /* ODO-CAN-GPS Reset (Active Low) */ + gpio_request(AT91_PIN_PB3, "ocg_rst"); /*PB12*/ + gpio_direction_output(AT91_PIN_PB3, 1); + gpio_export(AT91_PIN_PB3, true); + + /* GSM GPIO - User availabled GPIO */ + gpio_request(AT91_PIN_PC26, "gsm_gpio"); /*PB29*/ + at91_set_gpio_input(AT91_PIN_PC26, 0); + gpio_export(AT91_PIN_PC26, true); + /* GSM Reset (Active Low) */ + gpio_request(AT91_PIN_PC27, "gsm_rst"); /*PB30*/ + at91_set_gpio_input(AT91_PIN_PC27, 0); + gpio_export(AT91_PIN_PC27, true); + /* GSM Power (Active Low) */ + gpio_request(AT91_PIN_PC28, "gsm_pwr"); /*PB31*/ + at91_set_gpio_input(AT91_PIN_PC28, 0); + gpio_export(AT91_PIN_PC28, true); + + /* ADC Multiplexer (Channels 0-14, Default Channel 15 (null input)) */ + gpio_request(AT91_PIN_PC22, "admux0"); /*PC6*/ + gpio_request(AT91_PIN_PC23, "admux1"); /*PC7*/ + gpio_request(AT91_PIN_PC24, "admux2"); /*PC8*/ + gpio_request(AT91_PIN_PC25, "admux3"); /*PC9*/ + gpio_direction_output(AT91_PIN_PC22, 1); + gpio_direction_output(AT91_PIN_PC23, 1); + gpio_direction_output(AT91_PIN_PC24, 1); + gpio_direction_output(AT91_PIN_PC25, 1); + gpio_export(AT91_PIN_PC22, false); + gpio_export(AT91_PIN_PC23, false); + gpio_export(AT91_PIN_PC24, false); + gpio_export(AT91_PIN_PC25, false); + +} + +static void __init c3ax03_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&c3ax03_usbh_data); + /* USB Device */ + at91_add_device_udc(&c3ax03_udc_data); + /* I2C */ + at91_add_device_i2c(c3ax03_i2c_devices, + ARRAY_SIZE(c3ax03_i2c_devices)); + /* NAND FLash*/ + c3ax03_add_device_nand(); + /* Ethernet */ + at91_add_device_eth(&c3ax03_macb_data); + /* MMC */ + at91_add_device_mmc(0, &c3ax03_mmc_data); + /* LEDs */ + at91_gpio_leds(c3ax03_leds, ARRAY_SIZE(c3ax03_leds)); + /* Interrupts */ + c3ax03_add_device_buttons(); + /* GPIOs */ + c3ax03_init_gpio(); +} + +MACHINE_START(C3AX03, "Daricom C3-Ax03") + /* Maintainer: Patrick Bellasi */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = c3ax03_map_io, + .init_irq = c3ax03_init_irq, + .init_machine = c3ax03_board_init, +MACHINE_END -- 1.6.3.3