From: wellsk40@gmail.com (wellsk40 at gmail.com) Date: Mon, 8 Feb 2010 16:11:21 -0800 Subject: LPC32XX architecture files (updated v3) Message-ID: <1265674295-23996-1-git-send-email-wellsk40@gmail.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org This patchset is the third release of the LPC32xx arch files with many applicable review comments incorporated. Thank you everyone that helped review and improve this release. Changes from previous release to v3 (02/08/2010) Removed __initdata tag from clock lookup array. Removed include from irq entry macro. Added LPC32XX identifier to device specific names for register addresses, bitfields, and other macros Added LPC32XX identifier to device specific IRQ names Changes to suspend.S to make it more readable Changed register addresses and macros to return a virtual address via io_p2v of void __iomem * type. Previous types in the code that uses a different type now use void __iomem *. This makes the code less busy and fixes many sparse warnings. Most io_p2v() use in the code has been removed. _readl/_writel functions use the correct type now without the use of __force. _readl/_writel function arguments all use the direct virtual address or an indiced address (for devices that share register sets such as timers and UARTs). Some minor tweaks for sparse warnings Remove GENERIC_GPIO from arch/arm/Kconfig for mach-LPC32xx Updated phy3250_defconfig file The platform Kconfig.plat file was removed. Arch Kconfig was reduced just the serial port selections. Added mutex instead of local_irq..() for clock locks. Revised clock_get_rate code. All clock functions have a get_rate callback now instead of just LCD and MCI. Changed the way the rate fetch loop was handled. Switches to abs() and removed clkpwr_abs for clock driver functions. Simplified clock PLL rate config logic. Fixed USB PLL enable with correct timeout. Global fixes for all GPL license headers - remove wrong address. Changed I2C naming to start at '1' instead of '0' to match hardware convention. Added IRAM size autodetect function. Removed printascii() use in arch file. Fixed multi-line comments. Moved some register macros used just in GPIO driver to the GPIO driver from platform.h Added GPIO pin to bit mapping macros Fixed some names "na" in GPIO name array to NULL. Expanded a few GPIO driver comments to help explain the more wierd mappings better. Revised debug and uncompress macros to just use the serial port UART5 for the output (used on Phytec board). Revised interrupt handler and entry macro to use chained interrupt handlers for SIC1 and SIC2. Fixed several CLKPWR bit and IRQ macro names that could cause confusion with GPI names and the LPC32XX User's guide Changed VMALLOC_END to 0xF0000000 from PAGE_OFFSET+0x10000000 Added support for set_irq_wake in the interrupt driver with the supported wakeup sources. Activation level for GPIO events is inherited from the GPIO interrupt config. The level handlers are used for hardware based level and edge interrupts. Thsi is ok for this controller. Interrupt driver edge/level type logic reduction FIQ interrupts are no longer enabled by default in the MIC Changed all readl/writel calls to __raw_readl/__raw_writel. Removed support for Phytec board variations. This will only effect very eaarly LCD based boards. Due to the very limited number of boards out there, this really is not needed. Remove board specific code and associated config option for setting IRAM as the video frame buffer Moved IRDA enable/disable from the serial setup code to the board specific init code. Removed event setup code in board init, replaced with set_irq_wake functionality now CPU suspend removed, mem suspend only supported Allocation and dealloc of temporary storage for IRAM data used for suspend is no longer GFP_ATOMIC. Code will only alloc when needed and free on completion. Removed the pm_event driver, replaced (in part) with the set_irq_wake support. Events not supported by the set_irq_wake functionality need to be configured in the board specific init code. Changed some config names and descriptions for serial port setup in KConfig and the serial init code. Const modifier added to GPIO names