From: Ben Dooks Subject: [PATCH 04/23] ARM: H1940: Change h1940-bluetooth to use gpiolib API Date: Fri, 7 May 2010 08:15:26 +0900 Message-ID: <1273187745-6566-5-git-send-email-ben-linux@fluff.org> References: <1273187745-6566-1-git-send-email-ben-linux@fluff.org> Return-path: Received: from [121.136.51.148] ([121.136.51.148]:60610 "EHLO ben-laptop" rhost-flags-FAIL-FAIL-OK-FAIL) by vger.kernel.org with ESMTP id S1752746Ab0EFXQD (ORCPT ); Thu, 6 May 2010 19:16:03 -0400 In-Reply-To: <1273187745-6566-1-git-send-email-ben-linux@fluff.org> Sender: linux-samsung-soc-owner@vger.kernel.org List-Id: linux-samsung-soc@vger.kernel.org To: linux-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org Cc: Ben Dooks Change the h1940-bluetooth driver to use gpiolib to set the output state of GPH1. Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2410/h1940-bluetooth.c | 16 ++++++++++++---- 1 files changed, 12 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c index a3f3c7b..6d06b7e 100644 --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -33,14 +33,15 @@ static void h1940bt_enable(int on) h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); /* Reset the chip */ mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 1); + + gpio_set_value(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 0); + gpio_set_value(S3C2410_GPH(1), 0); } else { - s3c2410_gpio_setpin(S3C2410_GPH(1), 1); + gpio_set_value(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 0); + gpio_set_value(S3C2410_GPH(1), 0); mdelay(10); h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); } @@ -61,6 +62,12 @@ static int __devinit h1940bt_probe(struct platform_device *pdev) struct rfkill *rfk; int ret = 0; + ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev)); + if (ret) { + dev_err(&pdev->dev, "could not get GPH1\n");\ + return ret; + } + /* Configures BT serial port GPIOs */ s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); s3c2410_gpio_pullup(S3C2410_GPH(0), 1); @@ -100,6 +107,7 @@ static int h1940bt_remove(struct platform_device *pdev) struct rfkill *rfk = platform_get_drvdata(pdev); platform_set_drvdata(pdev, NULL); + gpio_free(S3C2410_GPH(1)); if (rfk) { rfkill_unregister(rfk); -- 1.7.0.4