Date: Thu, 22 Apr 1999 12:54:26 +0200 From: Toni Andjelkovic Subject: [linux-lvm] dazed and confused Message-ID: <19990422125426.A12508@overlord.telecom.at> Mime-Version: 1.0 Sender: owner-linux-lvm Errors-To: owner-linux-lvm List-Id: Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: linux-lvm@msede.com hi to all, i was greatly impressed when i stumbled across LVM, so i decided to try it immediately: i have 3 empty scsi-disks with 8.5 gigs each (/dev/sdc /dev/sdd /dev/sde) 64 heads, 32 sectors, 8678 cylinders. i created some partitions on each disk as follows: > (root@demon):[/usr/src/LVM/0.6/tools] # fdisk -l /dev/sdc > > Disk /dev/sdc: 64 heads, 32 sectors, 8678 cylinders > Units = cylinders of 2048 * 512 bytes > > Device Boot Start End Blocks Id System > /dev/sdc2 8551 8678 131072 82 Linux swap the first primary partition (cyl 1-8550) has an id of 0xfe. > (root@demon):[~] # vgscan > vgscan -- reading all physical volumes (this may take a while...) > vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created > vgscan -- WARNING: you may not have an actual backup of your volume group wonderful. > (root@demon):[~] # pvcreate /dev/sd[cde]1 > pvcreate -- reinitializing physical volume > pvcreate -- physical volume "/dev/sdc1" successfully created > pvcreate -- reinitializing physical volume > pvcreate -- physical volume "/dev/sdd1" successfully created > pvcreate -- reinitializing physical volume > pvcreate -- physical volume "/dev/sde1" successfully created i'm quite happy ... this looks good. > (root@demon):[~] # pvdisplay /dev/sd[cde]1 > pvdisplay -- "/dev/sdc1" is a new physical volume of 8.35 GB > pvdisplay -- "/dev/sdd1" is a new physical volume of 8.35 GB > pvdisplay -- "/dev/sde1" is a new physical volume of 8.35 GB and this looks even better. > (root@demon):[~] # vgcreate test_vg /dev/sd[cde]1 > vgcreate -- no valid physical volumes in command line > *ouch* ok, let's give it a try with the debug-switch on: > (root@demon):[~] # vgcreate -d test_vg /dev/sd[cde]1 > vg_check_name -- CALLED > vg_check_name -- vg_name: "test_vg" > lvm_check_chars -- CALLED > lvm_check_chars -- LEAVING > vg_check_name -- LEAVING with ret: 0 > lvm_iop_version -- CALLED > . > . > vgcreate -- no valid physical volumes in command line the interesting fact is that it'll scan every partition available, (from /dev/sd[cde]10 to /dev/sd[cde]20), but somehow it omits to mention /dev/sd[cde]1, where my physical volumes are located. never mind. i'll try to define the whole physical disk as a PV. i remove all existing partitions on /dev/sdc, > (root@demon):[/usr/src/LVM/0.6/tools] # fdisk -l /dev/sdc > > Disk /dev/sdc: 64 heads, 32 sectors, 8678 cylinders > Units = cylinders of 2048 * 512 bytes > > Device Boot Start End Blocks Id System and try > (root@demon):[/usr/src/LVM/0.6/tools] # pvcreate -d /dev/sdc > lvm_iop_version -- CALLED > lv_status_internal -- AFTER ioctl ret: 0 > lvm_iop_version -- LEAVING with ret: 0 > pv_check_name -- CALLED > lvm_check_chars -- CALLED > lvm_check_chars -- LEAVING > pv_check_name -- CALLED pv_name: "/dev/sdc" > pv_check_name -- LEAVING with ret: 0 > pv_get_size -- CALLED with /dev/sdc and BFFFF3AC > pv_check_name -- CALLED > lvm_check_chars -- CALLED > lvm_check_chars -- LEAVING > pv_check_name -- CALLED pv_name: "/dev/sdc" > pv_check_name -- LEAVING with ret: 0 > pv_check_part -- CALLED with /dev/sdc > pv_check_name -- CALLED > lvm_check_chars -- CALLED > lvm_check_chars -- LEAVING > pv_check_name -- CALLED pv_name: "/dev/sdc" > pv_check_name -- LEAVING with ret: 0 > pv_check_part -- LEAVING with -237 > pv_get_size -- BEFORE llseek 0:0 > pv_get_size -- part[0].sys_ind: 0 part[0].nr_sects: 0 > pv_get_size -- first == 1 > pv_get_size -- part[1].sys_ind: 0 part[1].nr_sects: 0 > pv_get_size -- first == 1 > pv_get_size -- part[2].sys_ind: 0 part[2].nr_sects: 0 > pv_get_size -- first == 1 > pv_get_size -- part[3].sys_ind: 0 part[3].nr_sects: 0 > pv_get_size -- first == 1 > pv_get_size -- LEAVING with ret: -242 > pvcreate -- extended partition "/dev/sdc" doesn't exist *scream* is it my fault? thx & cu, -- Toni Andjelkovic | (TA627-RIPE) | Tel: (+43 1) 21717-58990 toni@telecom.at | iT Austria | Fax: (+43 1) 21717-58900 ---------------------------------------------------------------------------