Received: from mailserv2.iuinc.com (qmailr@mailserv2.iuinc.com [206.245.164.55]) by puffin.external.hp.com (8.8.7/8.8.7) with SMTP id AAA00678 for ; Wed, 29 Dec 1999 00:16:04 -0700 Message-ID: <19991229071843.14892.qmail@web504.mail.yahoo.com> Date: Tue, 28 Dec 1999 23:18:43 -0800 (PST) From: Ulrich Strelow Subject: RE: [parisc-linux] cd-rom To: "Soto, Gene G." , "'Jan Bergman'" Cc: parisc-linux@thepuffingroup.com MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii List-ID: Although I used HP-UX 9.x some years ago, I don't know what your mounting problem is. But anyway, in order to install HP-UX 10.20 you NEED to BOOT from the CD. So please try to boot from the CD (e.g. press ESC during the boot sequence, search for bootable devices and select your CD hardware path 2.0.1.4.0). If you get any errors from this procedure, please post the error message(s) and the output from the search command. Ulrich -- "Soto, Gene G." wrote: > > I need to load 10.02 and am having problems > mounting a NEC > cdr-1410a cd-rom > > on my system (9000/712). Any advice on where to > go for help would > be > > appreciated. (SAM sees the device but I can't > mount it). > > > > thanks > > Maybe a stupid question, but I have had similar > problems with a > floppy drive. > Have you tried to mount it "by hand"? I.e. not > using SAM, "mount > /dev/dsk/c0tXd0 /cdrom" > where X is the SCSI ID. There might (but probably > not) also be a > conflict > with the SCSI ID. Does "ioscan" see the device? Try > to boot from the > CD, > if that doesn't work then I don't know. > > /Jan Bergman > jb@irfu.se > > > > correction: it is a NEC MultiSpin 2Xe (CDR-74-1) > > i have set the ID to 4. I also tried it on 3 and > it would not > detect it. > > it has 4 switches on the back and i have 1 & 2 set > opposite of what > is recommended > on the NEC webpage for installation on IBM or > compatibles (that's > the only way SAM > detected the device): > switch 1 is Factory Use Only(Normal OFF) (I have it > ON) > switch 2 is Termination ON/OFF (I have it OFF) > switch 3 is SCSI2/ON SCSI1/OFF (I have it OFF) > switch 4 is Factory Use Only(Normal OFF) (I have it > ON) > > I am running 9.01 (and don't have the 'n' option in > ioscan). > This is ioscan -f: > > Class H/W Path Driver H/W Status S/W > Status > > ===================================================== > graphics 1.0.0 graph3 ok(0x577) ok > > scsi 2.0.1 c700 ok(0x7071) ok > > disk 2.0.1.0.0 scsi ok(0x202) ok > > disk 2.0.1.1.0 scsi ok(0x202) ok > > disk 2.0.1.4.0 scsi ok(0x5800100) ok > > disk 2.0.1.5.0 scsi ok(0x202) ok > > disk 2.0.1.6.0 scsi ok(0x202) ok > > lan 2.0.2 lan01 ok(0x7072) ok > > hil 2.0.3 hil ok(0x7073) ok > > serial 2.0.4 asio0 ok(0x7075) ok > > serial 2.0.5 asio0 ok(0x7075) ok > > parallel 2.0.6 parallel ok(0x7074) ok > > > > I get the following note from SAM when I try to add > the disk: > SAM was unable to determine the disk model of one > of the disk drives > on your system, > and is assuming that disk drive is used. This may > happen if the > disk drive is a > disk array or if the disk is not listed in > /usr/sam/lib/C/pd_devinfo.tx. > > this is the only cd-rom info listed in > pd_devinfo.tx: > DISK:::scsi::::TOSHIBA CD-ROM XM-3301TA:::SCSI > CD-ROM > drive::::::::::::::::CDROM_SCSI, > DISK:::scsi::::TOSHIBA CD-ROM DRIVE:::::::SCSI > CD-ROM > drive::::::::::::::::CDROM_SCSI, > > is it possible to add something to pd_devinfo.tx > that would allow it > to mount? > > these are the device files: > /dev/dsk/4s0 > /dev/dsk/c201d4s0 > /dev/rdsk/4s0 > /dev/rdsk/c201d4s0 > > when I try adding the following entry to > /etc/checklist: > /dev/dsk/c201d4s0 /cdrom cdfs defaults > > i get the following message when i try to mount it: > /dev/dsk/c201d4s0: Device busy > > --------------------------------------------------------------------------- > To unsubscribe: send e-mail to > parisc-linux-request@thepuffingroup.com with > `unsubscribe' as the subject. > > __________________________________________________ Do You Yahoo!? Talk to your friends online with Yahoo! Messenger. http://messenger.yahoo.com