From: Jesper Anderson Subject: Pentium III Coppermine and 440BX/ZX/DX Date: Tue, 17 Feb 2004 01:55:04 +0100 Sender: cpufreq-bounces@www.linux.org.uk Message-ID: <20040217005504.GA809@acheron.utfors.se> Mime-Version: 1.0 Return-path: Content-Disposition: inline List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: cpufreq-bounces+glkc-cpufreq=gmane.org@www.linux.org.uk Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: cpufreq@www.linux.org.uk I have a Gateway Solo 3450 laptop, which is a PIII 750 MHz with a PIIX4 chipset. I'm trying to get both ACPI and cpufreq to work on it, with very little luck so far. The ACPI is its own kettel of fish, I suspect the BIOS might be rather broken (but then, which isn't?), but I was hoping the cpufreq issue could at least be somewhat easy to solve. Unfortunately I'm a bit unclear on just what I need to do to get cpufreq running on this system. I tried modprobing speedstep-smi (from kernel 2.6.2 with mm1), and it gives no errors - but neither does it give me anything to go on in /sys or /proc. speedstep-ich doesn't load at all. I tried the patch posted previously on the mailing list (that removes a few bits of the PIII check), but that didn't make any difference. I'm a bit at a loss as to where to go from here. speedstep-detect doesn't show any different output on battery or AC power, can that be a problem? Output of speedstep-detect is attached. Thanks in advance, Jesper # ./speedstep-detect dmi_scan: return: DMI present. 31 structures occupying 1004 bytes. DMI table at 0x000D3010. BIOS Vendor: Gateway BIOS Version: 28.06.04 BIOS Release: 03/14/2002 System Vendor: Gateway Product Name: Solo3450 Version: Rev 1.0 Board Vendor: Gateway Board Name: Solo3450 Board Version: Rev 1.0 Trying Intel's int15 GSIC: BIOS support GSIC call: signature: GSIC command port = 0x00b2 command = 0x0080 event port = 0x000000b3 flags = 0x07d00100 probing chipsets: Found PIIX4 pmbase at 0x8000 Dumping PM IO register for this southbridge: PMCNTRL (0x8004): 0x1401 (0x8006): 0x0000 GPEN (0x800e): 0x0e00 PCNTRL (0x8010): 0x00003a0c (0x8016): 0x0000 DEVSTS (0x801c): 0x00000000 GLBLEN (0x8020): 0x0400 (0x8022): 0x00000000 GLBCTL (0x8028): 0x06010305 DEVCTL (0x802c): 0x01200000 GPIs: (0x8030): 0x3fe343 (0x8033): 0x00 GPOs: (0x8034): 0x6c3fb7d1 (0x8038): 0x43 0xe3 0x3f 0x00 0xd1 0xb7 0x3f 0x6c You need to boot on AC and battery and see if GPOs change. Then, see if one bit change in between, you have then to note the number of this bit. This will be the gpo_hilo= number kernel option for enabling the speedstep-piix4 module under Linux. ..28..24..20..16..12...8...4...0 GPOs: (0x8034): 0x6c3fb7d1 01101100001111111011011111010001