From: Christoph Hellwig Subject: [PATCH] fdomain: reduce usage of global variables Date: Sun, 10 Oct 2004 15:08:21 +0200 Sender: linux-scsi-owner@vger.kernel.org Message-ID: <20041010130820.GA2728@lst.de> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Received: from verein.lst.de ([213.95.11.210]:18347 "EHLO mail.lst.de") by vger.kernel.org with ESMTP id S268299AbUJJNIZ (ORCPT ); Sun, 10 Oct 2004 09:08:25 -0400 Content-Disposition: inline List-Id: linux-scsi@vger.kernel.org To: jejb@steeleye.com Cc: linux-scsi@vger.kernel.org preparation for supporting more than HBA instance --- 1.30/drivers/scsi/fdomain.c 2004-08-26 03:50:07 +02:00 +++ edited/drivers/scsi/fdomain.c 2004-10-09 17:30:27 +02:00 @@ -400,20 +400,6 @@ static volatile int in_interrupt_flag; #endif -static int SCSI_Mode_Cntl_port; -static int FIFO_Data_Count_port; -static int Interrupt_Cntl_port; -static int Interrupt_Status_port; -static int Read_FIFO_port; -static int Read_SCSI_Data_port; -static int SCSI_Cntl_port; -static int SCSI_Data_NoACK_port; -static int SCSI_Status_port; -static int TMC_Cntl_port; -static int TMC_Status_port; -static int Write_FIFO_port; -static int Write_SCSI_Data_port; - static int FIFO_Size = 0x2000; /* 8k FIFO for pre-tmc18c30 chips */ @@ -585,12 +571,12 @@ inline static void fdomain_make_bus_idle( void ) { - outb( 0, SCSI_Cntl_port ); - outb( 0, SCSI_Mode_Cntl_port ); + outb(0, port_base + SCSI_Cntl); + outb(0, port_base + SCSI_Mode_Cntl); if (chip == tmc18c50 || chip == tmc18c30) - outb( 0x21 | PARITY_MASK, TMC_Cntl_port ); /* Clear forced intr. */ + outb(0x21 | PARITY_MASK, port_base + TMC_Cntl); /* Clear forced intr. */ else - outb( 0x01 | PARITY_MASK, TMC_Cntl_port ); + outb(0x01 | PARITY_MASK, port_base + TMC_Cntl); } static int fdomain_is_valid_port( int port ) @@ -910,20 +896,6 @@ } } - SCSI_Mode_Cntl_port = port_base + SCSI_Mode_Cntl; - FIFO_Data_Count_port = port_base + FIFO_Data_Count; - Interrupt_Cntl_port = port_base + Interrupt_Cntl; - Interrupt_Status_port = port_base + Interrupt_Status; - Read_FIFO_port = port_base + Read_FIFO; - Read_SCSI_Data_port = port_base + Read_SCSI_Data; - SCSI_Cntl_port = port_base + SCSI_Cntl; - SCSI_Data_NoACK_port = port_base + SCSI_Data_NoACK; - SCSI_Status_port = port_base + SCSI_Status; - TMC_Cntl_port = port_base + TMC_Cntl; - TMC_Status_port = port_base + TMC_Status; - Write_FIFO_port = port_base + Write_FIFO; - Write_SCSI_Data_port = port_base + Write_SCSI_Data; - fdomain_16x0_bus_reset(NULL); if (fdomain_test_loopback()) { @@ -1032,13 +1004,13 @@ printk( "fdomain_arbitrate()\n" ); #endif - outb( 0x00, SCSI_Cntl_port ); /* Disable data drivers */ - outb( adapter_mask, port_base + SCSI_Data_NoACK ); /* Set our id bit */ - outb( 0x04 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */ + outb(0x00, port_base + SCSI_Cntl); /* Disable data drivers */ + outb(adapter_mask, port_base + SCSI_Data_NoACK); /* Set our id bit */ + outb(0x04 | PARITY_MASK, port_base + TMC_Cntl); /* Start arbitration */ timeout = 500; do { - status = inb( TMC_Status_port ); /* Read adapter status */ + status = inb(port_base + TMC_Status); /* Read adapter status */ if (status & 0x02) /* Arbitration complete */ return 0; mdelay(1); /* Wait one millisecond */ @@ -1065,19 +1037,19 @@ static int flag = 0; #endif - outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */ - outb( adapter_mask | (1 << target), SCSI_Data_NoACK_port ); + outb(0x82, port_base + SCSI_Cntl); /* Bus Enable + Select */ + outb(adapter_mask | (1 << target), port_base + SCSI_Data_NoACK); /* Stop arbitration and enable parity */ - outb( PARITY_MASK, TMC_Cntl_port ); + outb(PARITY_MASK, port_base + TMC_Cntl); timeout = 350; /* 350 msec */ do { - status = inb( SCSI_Status_port ); /* Read adapter status */ + status = inb(port_base + SCSI_Status); /* Read adapter status */ if (status & 1) { /* Busy asserted */ /* Enable SCSI Bus (on error, should make bus idle with 0) */ - outb( 0x80, SCSI_Cntl_port ); + outb(0x80, port_base + SCSI_Cntl); return 0; } mdelay(1); /* wait one msec */ @@ -1102,7 +1074,7 @@ { if (in_command) { in_command = 0; - outb( 0x00, Interrupt_Cntl_port ); + outb(0x00, port_base + Interrupt_Cntl); fdomain_make_bus_idle(); current_SC->result = error; if (current_SC->scsi_done) @@ -1131,11 +1103,11 @@ running. */ /* Check for other IRQ sources */ - if((inb(TMC_Status_port)&0x01)==0) + if ((inb(port_base + TMC_Status) & 0x01) == 0) return IRQ_NONE; /* It is our IRQ */ - outb( 0x00, Interrupt_Cntl_port ); + outb(0x00, port_base + Interrupt_Cntl); /* We usually have one spurious interrupt after each command. Ignore it. */ if (!in_command || !current_SC) { /* Spurious interrupt */ @@ -1160,7 +1132,7 @@ #endif if (current_SC->SCp.phase & in_arbitration) { - status = inb( TMC_Status_port ); /* Read adapter status */ + status = inb(port_base + TMC_Status); /* Read adapter status */ if (!(status & 0x02)) { #if EVERY_ACCESS printk( " AFAIL " ); @@ -1172,19 +1144,19 @@ } current_SC->SCp.phase = in_selection; - outb( 0x40 | FIFO_COUNT, Interrupt_Cntl_port ); + outb(0x40 | FIFO_COUNT, port_base + Interrupt_Cntl); - outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */ - outb( adapter_mask | (1 << current_SC->device->id), SCSI_Data_NoACK_port ); + outb(0x82, port_base + SCSI_Cntl); /* Bus Enable + Select */ + outb(adapter_mask | (1 << current_SC->device->id), port_base + SCSI_Data_NoACK); /* Stop arbitration and enable parity */ - outb( 0x10 | PARITY_MASK, TMC_Cntl_port ); + outb(0x10 | PARITY_MASK, port_base + TMC_Cntl); #if DEBUG_RACE in_interrupt_flag = 0; #endif return IRQ_HANDLED; } else if (current_SC->SCp.phase & in_selection) { - status = inb( SCSI_Status_port ); + status = inb(port_base + SCSI_Status); if (!(status & 0x01)) { /* Try again, for slow devices */ if (fdomain_select( current_SC->device->id )) { @@ -1200,12 +1172,12 @@ printk( " AltSel " ); #endif /* Stop arbitration and enable parity */ - outb( 0x10 | PARITY_MASK, TMC_Cntl_port ); + outb(0x10 | PARITY_MASK, port_base + TMC_Cntl); } } current_SC->SCp.phase = in_other; - outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port ); - outb( 0x80, SCSI_Cntl_port ); + outb(0x90 | FIFO_COUNT, port_base + Interrupt_Cntl); + outb(0x80, port_base + SCSI_Cntl); #if DEBUG_RACE in_interrupt_flag = 0; #endif @@ -1214,15 +1186,15 @@ /* current_SC->SCp.phase == in_other: this is the body of the routine */ - status = inb( SCSI_Status_port ); + status = inb(port_base + SCSI_Status); if (status & 0x10) { /* REQ */ switch (status & 0x0e) { case 0x08: /* COMMAND OUT */ - outb( current_SC->cmnd[current_SC->SCp.sent_command++], - Write_SCSI_Data_port ); + outb(current_SC->cmnd[current_SC->SCp.sent_command++], + port_base + Write_SCSI_Data); #if EVERY_ACCESS printk( "CMD = %x,", current_SC->cmnd[ current_SC->SCp.sent_command - 1] ); @@ -1231,17 +1203,17 @@ case 0x00: /* DATA OUT -- tmc18c50/tmc18c30 only */ if (chip != tmc1800 && !current_SC->SCp.have_data_in) { current_SC->SCp.have_data_in = -1; - outb( 0xd0 | PARITY_MASK, TMC_Cntl_port ); + outb(0xd0 | PARITY_MASK, port_base + TMC_Cntl); } break; case 0x04: /* DATA IN -- tmc18c50/tmc18c30 only */ if (chip != tmc1800 && !current_SC->SCp.have_data_in) { current_SC->SCp.have_data_in = 1; - outb( 0x90 | PARITY_MASK, TMC_Cntl_port ); + outb(0x90 | PARITY_MASK, port_base + TMC_Cntl); } break; case 0x0c: /* STATUS IN */ - current_SC->SCp.Status = inb( Read_SCSI_Data_port ); + current_SC->SCp.Status = inb(port_base + Read_SCSI_Data); #if EVERY_ACCESS printk( "Status = %x, ", current_SC->SCp.Status ); #endif @@ -1257,10 +1229,10 @@ #endif break; case 0x0a: /* MESSAGE OUT */ - outb( MESSAGE_REJECT, Write_SCSI_Data_port ); /* Reject */ + outb(MESSAGE_REJECT, port_base + Write_SCSI_Data); /* Reject */ break; case 0x0e: /* MESSAGE IN */ - current_SC->SCp.Message = inb( Read_SCSI_Data_port ); + current_SC->SCp.Message = inb(port_base + Read_SCSI_Data); #if EVERY_ACCESS printk( "Message = %x, ", current_SC->SCp.Message ); #endif @@ -1281,17 +1253,17 @@ if(current_SC->sc_data_direction == DMA_TO_DEVICE) { current_SC->SCp.have_data_in = -1; - outb( 0xd0 | PARITY_MASK, TMC_Cntl_port ); + outb(0xd0 | PARITY_MASK, port_base + TMC_Cntl); } else { current_SC->SCp.have_data_in = 1; - outb( 0x90 | PARITY_MASK, TMC_Cntl_port ); + outb(0x90 | PARITY_MASK, port_base + TMC_Cntl); } } if (current_SC->SCp.have_data_in == -1) { /* DATA OUT */ - while ( (data_count = FIFO_Size - inw( FIFO_Data_Count_port )) > 512 ) { + while ((data_count = FIFO_Size - inw(port_base + FIFO_Data_Count)) > 512) { #if EVERY_ACCESS printk( "DC=%d, ", data_count ) ; #endif @@ -1302,11 +1274,11 @@ printk( "%d OUT, ", data_count ); #endif if (data_count == 1) { - outb( *current_SC->SCp.ptr++, Write_FIFO_port ); + outb(*current_SC->SCp.ptr++, port_base + Write_FIFO); --current_SC->SCp.this_residual; } else { data_count >>= 1; - outsw( Write_FIFO_port, current_SC->SCp.ptr, data_count ); + outsw(port_base + Write_FIFO, current_SC->SCp.ptr, data_count); current_SC->SCp.ptr += 2 * data_count; current_SC->SCp.this_residual -= 2 * data_count; } @@ -1324,7 +1296,7 @@ } if (current_SC->SCp.have_data_in == 1) { /* DATA IN */ - while ((data_count = inw( FIFO_Data_Count_port )) > 0) { + while ((data_count = inw(port_base + FIFO_Data_Count)) > 0) { #if EVERY_ACCESS printk( "DC=%d, ", data_count ); #endif @@ -1335,11 +1307,11 @@ printk( "%d IN, ", data_count ); #endif if (data_count == 1) { - *current_SC->SCp.ptr++ = inb( Read_FIFO_port ); + *current_SC->SCp.ptr++ = inb(port_base + Read_FIFO); --current_SC->SCp.this_residual; } else { data_count >>= 1; /* Number of words */ - insw( Read_FIFO_port, current_SC->SCp.ptr, data_count ); + insw(port_base + Read_FIFO, current_SC->SCp.ptr, data_count); current_SC->SCp.ptr += 2 * data_count; current_SC->SCp.this_residual -= 2 * data_count; } @@ -1399,10 +1371,10 @@ } else { if (current_SC->SCp.phase & disconnect) { - outb( 0xd0 | FIFO_COUNT, Interrupt_Cntl_port ); - outb( 0x00, SCSI_Cntl_port ); + outb(0xd0 | FIFO_COUNT, port_base + Interrupt_Cntl); + outb(0x00, port_base + SCSI_Cntl); } else { - outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port ); + outb(0x90 | FIFO_COUNT, port_base + Interrupt_Cntl); } } #if DEBUG_RACE @@ -1453,12 +1425,12 @@ current_SC->SCp.phase = in_arbitration; /* Start arbitration */ - outb( 0x00, Interrupt_Cntl_port ); - outb( 0x00, SCSI_Cntl_port ); /* Disable data drivers */ - outb( adapter_mask, SCSI_Data_NoACK_port ); /* Set our id bit */ + outb(0x00, port_base + Interrupt_Cntl); + outb(0x00, port_base + SCSI_Cntl); /* Disable data drivers */ + outb(adapter_mask, port_base + SCSI_Data_NoACK); /* Set our id bit */ ++in_command; - outb( 0x20, Interrupt_Cntl_port ); - outb( 0x14 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */ + outb(0x20, port_base + Interrupt_Cntl); + outb(0x14 | PARITY_MASK, port_base + TMC_Cntl); /* Start arbitration */ return 0; } @@ -1514,17 +1486,17 @@ printk( " (masked)" ); printk( ", IRR = 0x%04x, ISR = 0x%04x\n", irr, isr ); - printk( "SCSI Status = 0x%02x\n", inb( SCSI_Status_port ) ); - printk( "TMC Status = 0x%02x", inb( TMC_Status_port ) ); - if (inb( TMC_Status_port & 1)) + printk( "SCSI Status = 0x%02x\n", inb(port_base + SCSI_Status)); + printk( "TMC Status = 0x%02x", inb(port_base + TMC_Status)); + if (inb((port_base + TMC_Status) & 1)) printk( " (interrupt)" ); printk( "\n" ); - printk( "Interrupt Status = 0x%02x", inb( Interrupt_Status_port ) ); - if (inb( Interrupt_Status_port ) & 0x08) + printk("Interrupt Status = 0x%02x", inb(port_base + Interrupt_Status)); + if (inb(port_base + Interrupt_Status) & 0x08) printk( " (enabled)" ); printk( "\n" ); if (chip == tmc18c50 || chip == tmc18c30) { - printk( "FIFO Status = 0x%02x\n", inb( port_base + FIFO_Status ) ); + printk("FIFO Status = 0x%02x\n", inb(port_base + FIFO_Status)); printk( "Int. Condition = 0x%02x\n", inb( port_base + Interrupt_Cond ) ); } @@ -1563,12 +1535,12 @@ int fdomain_16x0_bus_reset(struct scsi_cmnd *SCpnt) { - outb( 1, SCSI_Cntl_port ); + outb(1, port_base + SCSI_Cntl); do_pause( 2 ); - outb( 0, SCSI_Cntl_port ); + outb(0, port_base + SCSI_Cntl); do_pause( 115 ); - outb( 0, SCSI_Mode_Cntl_port ); - outb( PARITY_MASK, TMC_Cntl_port ); + outb(0, port_base + SCSI_Mode_Cntl); + outb(PARITY_MASK, port_base + TMC_Cntl); return SUCCESS; }