From: Bernd Schubert Subject: Re: tg3: tg3_stop_block timed out Date: Tue, 8 Aug 2006 01:24:38 +0200 Message-ID: <200608080124.38823.bernd-schubert@gmx.de> References: <1154992063.5328.3.camel@rh4> Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-15 Content-Transfer-Encoding: QUOTED-PRINTABLE Cc: netdev@vger.kernel.org Return-path: Received: from mail.gmx.de ([213.165.64.20]:156 "HELO mail.gmx.net") by vger.kernel.org with SMTP id S1751198AbWHGXYd convert rfc822-to-8bit (ORCPT ); Mon, 7 Aug 2006 19:24:33 -0400 To: "Michael Chan" In-Reply-To: <1154992063.5328.3.camel@rh4> Content-Disposition: inline Sender: netdev-owner@vger.kernel.org List-Id: netdev.vger.kernel.org Hi Michael, thanks for your help! On Tuesday 08 August 2006 01:07, Michael Chan wrote: > > ... [many hamilton not responding messages] > > 4554928.798000] nfs: server hamilton not responding, still trying > > [4554935.319000] nfs: server hamilton not responding, still trying > > [4555468.940000] NETDEV WATCHDOG: eth1: transmit timed out > > [4555468.940000] tg3: eth1: transmit timed out, resetting > > [4555469.044000] tg3: tg3_stop_block timed out, ofs=3D3400 enable_b= it=3D2 > > [4555469.147000] tg3: tg3_stop_block timed out, ofs=3D2400 enable_b= it=3D2 > > [4555469.251000] tg3: tg3_stop_block timed out, ofs=3D1400 enable_b= it=3D2 > > [4555469.354000] tg3: tg3_stop_block timed out, ofs=3Dc00 enable_bi= t=3D2 > > [4555469.433000] tg3: eth1: Link is down. > > [4555472.593000] tg3: eth1: Link is up at 1000 Mbps, full duplex. > > [4555472.594000] tg3: eth1: Flow control is on for TX and on for RX= =2E > > [4555498.016000] nfs: server 129.206.21.200 OK > > [4555648.015000] nfs: server 129.206.21.200 OK > > ... [many ok messages] > > I need to know what hardware you're using so please send me the tg3 > probing output for eth1 when you load the driver. Do you have TSO > enabled? tg3.c:v3.49 (Feb 2, 2006) acpi_bus-0201 [01] bus_set_power : Device is not power manageab= le eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bi= t) 10/100/1000BaseT Ethernet 00:e0:81:2b:aa:28 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TS= Ocap[0] eth1: dma_rwctrl[769f4000] dma_mask[64-bit] eth2: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bi= t) 10/100/1000BaseT Ethernet 00:e0:81:2b:aa:29 eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TS= Ocap[1] eth2: dma_rwctrl[769f4000] dma_mask[64-bit] The NIC is onboard a Tyan S2882.=20 0000:02:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM570= 4 Gigabit Ethernet (rev 03) Subsystem: Broadcom Corporation: Unknown device 1644 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 24 Memory at fc8c0000 (64-bit, non-prefetchable) [size=3D64K] Memory at fc8b0000 (64-bit, non-prefetchable) [size=3D64K] Capabilities: [40] Capabilities: [48] Power Management ver= sion 2 Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=3D= 0/3 Enable- 0000:02:09.1 Ethernet controller: Broadcom Corporation NetXtreme BCM570= 4 Gigabit Ethernet (rev 03) Subsystem: Broadcom Corporation: Unknown device 1644 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 25 Memory at fc8e0000 (64-bit, non-prefetchable) [size=3D64K] Memory at fc8d0000 (64-bit, non-prefetchable) [size=3D64K] Capabilities: [40] Capabilities: [48] Power Management ver= sion 2 Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=3D= 0/3 Enable- The driver is compiled into the kernel (its a nfs-root booted system an= d=20 NIC modules are presently not supported by our initrd). So the default option for tso is set. Is there any way to determine the= =20 present tso setting? With ethtool I only find the options to turn it of= f/on,=20 but none to query the current state. Thanks a lot, Bernd --=20 Bernd Schubert PCI / Theoretische Chemie Universit=E4t Heidelberg INF 229 69120 Heidelberg