From: Sergei Shtylyov Subject: [PATCH 2.6.20-rc2-mm1] HPT36x PCI clock detection fix Date: Sat, 30 Dec 2006 22:36:36 +0300 Message-ID: <200612302236.36285.sshtylyov@ru.mvista.com> Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Return-path: Received: from h155.mvista.com ([63.81.120.155]:64660 "EHLO imap.sh.mvista.com" rhost-flags-OK-FAIL-OK-FAIL) by vger.kernel.org with ESMTP id S1030313AbWL3Tgy (ORCPT ); Sat, 30 Dec 2006 14:36:54 -0500 Content-Disposition: inline Sender: linux-ide-owner@vger.kernel.org List-Id: linux-ide@vger.kernel.org To: akpm@osdl.org, bzolnier@gmail.com Cc: linux-ide@vger.kernel.org, alan@lxorguk.ukuu.org.uk Fix minor coding mistake in the HPT36x PCI clock detection code noticed by Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing 'break' statements. This, however, most probably never mattered -- in fact, I was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e. supported only 33 MHz PCI. Note that in the original driver there was another bug: 25 and 40 MHz cases were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks, a lower clock count just *cannot* correspond to a higher frequency, i. e. it should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around. Signed-off-by: Sergei Shtylyov drivers/ide/pci/hpt366.c | 8 ++++++-- 1 files changed, 6 insertions(+), 2 deletions(-) Index: linux-2.6/drivers/ide/pci/hpt366.c =================================================================== --- linux-2.6.orig/drivers/ide/pci/hpt366.c +++ linux-2.6/drivers/ide/pci/hpt366.c @@ -1,5 +1,5 @@ /* - * linux/drivers/ide/pci/hpt366.c Version 1.00 Jun 25, 2006 + * linux/drivers/ide/pci/hpt366.c Version 1.01 Dec 23, 2006 * * Copyright (C) 1999-2003 Andre Hedrick * Portions Copyright (C) 2001 Sun Microsystems, Inc. @@ -107,7 +107,8 @@ * frequency * - switch to using the DPLL clock and enable UltraATA/133 mode by default on * anything newer than HPT370/A - * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(); + * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(), + * also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips; * unify HPT36x/37x timing setup code and the speedproc handlers by joining * the register setting lists into the table indexed by the clock selected * Sergei Shtylyov, or @@ -1125,11 +1126,14 @@ static unsigned int __devinit init_chips switch((itr1 >> 8) & 0x07) { case 0x09: pci_clk = 40; + break; case 0x05: pci_clk = 25; + break; case 0x07: default: pci_clk = 33; + break; } }