From: Joerg Sommrey Date: Thu, 09 Aug 2007 07:09:15 +0000 Subject: Re: [lm-sensors] bad temperature values from w83781d in 2.6.22 Message-Id: <20070809070915.GA24252@sommrey.de> List-Id: References: <20070805183219.0d54802b.akpm@linux-foundation.org> <20070808010316.GB3584@jupiter.solarsys.private> <20070808151716.GA6053@sommrey.de> <20070809035642.GE3584@jupiter.solarsys.private> In-Reply-To: <20070809035642.GE3584@jupiter.solarsys.private> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable To: "Mark M. Hoffman" Cc: LKML , lm-sensors Hi Mark, On Wed, Aug 08, 2007 at 11:56:42PM -0400, Mark M. Hoffman wrote: > Hi Joerg: >=20 > * Joerg Sommrey [2007-08-08 17:17:16 +0200]: > > Hi Mark, > >=20 > > just to eliminate as many impacts as possible, I did: > > - reinstall the unmodified sensors.conf from Tyan's support page > > - power off before rebooting > >=20 > > A call to "sensors -s" is done without errors in all cases. > > The module parameters I use currently with both kernels: > >=20 > > options w83781d force_w83782d=3D0,0x2d force_subclients=3D0,0x2d,0x48,0= x49 > > options w83627hf force_addr=3D0x0c00 > >=20 > > When I first realized the problem, I didn't use w83627hf yet. Results > > are the same when w83781d is used as driver for w83627hf. > > Parameters in that case just from Tyan: > >=20 > > options w83781d force_w83782d=3D0,0x2d force_subclients=3D0,0x2d,0x48,0= x49 force_w83627hf=3D0,0x2c force_subclients=3D0,0x2c,0x4a,0x4b init=3D0 > >=20 > > "My" i2cdump doesn't accept an -y option, maybe a Debianism. Results > > see below. >=20 > Newer i2cdump skips the 5-second warning when given -y, that's all. >=20 > > ### 2.6.21 ############################### > > Script started on Wed Aug 8 16:53:10 2007 > > bear:~/hwmon# i2cdump 0 0x2d b 0 0x4e >=20 > (snip tons of results) >=20 > Thanks for sending all that. I see one bug clearly, and I'm pretty close= to > seeing the other one. But for tonight, I need sleep. >=20 > In the meantime, please try this command as root, against the newer kerne= l, > *after* you've done 'sensors -s': >=20 > # i2cset -f 0 0x2d 0x5d 0x0e b >=20 > Wait > 2 seconds for the hardware to update itself, then run 'sensors' ag= ain. > I'm pretty sure you'll see the correct temps. The displayed temperatures changed to 67.5=B0C / 66.0=B0C. Still, this see= ms to be too high. The power supply's fan runs too slow for such CPU temperatures. In older kernels it becomes noisy above 50=B0C. Under load the temperatures shown are around 95=B0C, way too high. -jo --=20 -rw-r--r-- 1 jo users 62 2007-08-08 21:06 /home/jo/.signature _______________________________________________ lm-sensors mailing list lm-sensors@lm-sensors.org http://lists.lm-sensors.org/mailman/listinfo/lm-sensors