From: Jean-Christophe PLAGNIOL-VILLARD Date: Sat, 23 May 2009 02:01:14 +0200 Subject: [U-Boot] [PATCH] at91: Add support for MEESC board of esd gmbh In-Reply-To: <12426456553434-git-send-email-Daniel.Gorsulowski@esd.eu> References: <1242645655326-git-send-email-Daniel.Gorsulowski@esd.eu> <12426456553434-git-send-email-Daniel.Gorsulowski@esd.eu> Message-ID: <20090523000114.GG19891@game.jcrosoft.org> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de > + > +static void meesc_ethercat_hw_init(void) > +{ > + /* Configure SMC EBI1_CS0 for EtherCAT */ > + at91_sys_write(AT91_SMC1_SETUP(0), > + AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) | > + AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0)); > + at91_sys_write(AT91_SMC1_PULSE(0), > + AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(9) | > + AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9)); > + at91_sys_write(AT91_SMC1_CYCLE(0), > + AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5)); > + /* Configure behavior at external wait signal, byte-select mode, 16 bit > + data bus width, none data float wait states and TDF optimization */ > + at91_sys_write(AT91_SMC1_MODE(0), > + AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY | > + AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) | > + AT91_SMC_TDFMODE); > + > + /* Configure RDY/BSY */ > + at91_set_B_periph(AT91_PIN_PE20, 0); /* EBI1_NWAIT */ do you really need this you do not seems to use it anywhere? > +} > + > +#ifdef CONFIG_HAS_DATAFLASH please keep the file organisation as the other at91sam9 > +AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS]; > + > +struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = { > + {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0}, /* Logical adress, CS */ > +}; > + > +/* define the area offsets */ > +dataflash_protect_t area_list[NB_DATAFLASH_AREA] = { > + {0x00000000, 0x000041FF, FLAG_PROTECT_SET, 0, "Bootstrap"}, > + {0x00004200, 0x000083FF, FLAG_PROTECT_CLEAR, 0, "Environment"}, > + {0x00008400, 0x00041FFF, FLAG_PROTECT_SET, 0, "U-Boot"}, > +}; > +#endif /* CONFIG_HAS_DATAFLASH */ > + > +int dram_init(void) > +{ > + gd->bd->bi_dram[0].start = PHYS_SDRAM; > + gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27)); > + return 0; > +} > + > +int board_eth_init(bd_t *bis) > +{ > + int rc = 0; > +#ifdef CONFIG_MACB > + rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x00); > +#endif > + return rc; > +} > + > +int checkboard(void) > +{ > + char str[32]; > + char buf[32]; > + > + puts("Board: esd CAN-EtherCAT Gateway"); > + if (getenv_r("serial#", str, sizeof(str)) > 0) { > + puts(", serial# "); > + puts(str); > + } > + printf("\nHardware-revision: 1.%d\n", get_hw_rev()); > + printf("Crystal frequency:\t%8s MHz\n", > + strmhz(buf, get_main_clk_rate())); > + printf("CPU clock:\t\t%8s MHz\n", > + strmhz(buf, get_cpu_clk_rate())); > +#ifdef CONFIG_SHOW_VERBOSE_CLOCKINFO > + printf("Master clock:\t\t%8s MHz\n", > + strmhz(buf, get_mck_clk_rate())); > + printf("PLL A clock:\t\t%8s MHz\n", > + strmhz(buf, get_plla_clk_rate())); > + printf("PLL B Reg.:\t\t0x%08X\n", > + at91_sys_read(AT91_CKGR_PLLBR)); > + printf("PLL B clock:\t\t%8s MHz\n", > + strmhz(buf, get_pllb_clk_rate())); > +#endif > + printf("Mach-type: %lu\n", gd->bd->bi_arch_number); > + return 0; > +} > + > +int board_init(void) > +{ > + /* Enable Ctrlc */ > + console_init_f(); > + > + /* Peripheral Clock Enable Register */ > + at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOA | > + 1 << AT91SAM9263_ID_PIOB | > + 1 << AT91SAM9263_ID_PIOCDE); > + > +#ifdef MACH_TYPE_MEESC /* while asm-arm/mach-types.h is not up to date */ you need to send a sync request > + /* arch number of MEESC-Board */ > + gd->bd->bi_arch_number = MACH_TYPE_MEESC; > +#else > + /* arch number of AT91SAM9263EK-Board */ > + gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK; please remove > +#endif > + /* adress of boot parameters */ > + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; > + > + at91_serial_hw_init(); > +#ifdef CONFIG_CMD_NAND > + meesc_nand_hw_init(); > +#endif > + meesc_ethercat_hw_init(); > +#ifdef CONFIG_HAS_DATAFLASH > + at91_spi0_hw_init(1 << 0); > +#endif > +#ifdef CONFIG_MACB > + meesc_macb_hw_init(); > +#endif Best Regards, J.