From: Ira Snyder Date: Wed, 3 Jun 2009 13:46:05 -0700 Subject: [U-Boot] TSEC ethernet controller problems (crc errors/ corruption) In-Reply-To: <20090603151905.b191e4b0.kim.phillips@freescale.com> References: <20090602194659.GA5471@ovro.caltech.edu> <20090602212503.GA16327@ovro.caltech.edu> <20090602221918.GB16327@ovro.caltech.edu> <20090602180817.079aa37f.kim.phillips@freescale.com> <20090603175025.GB7292@ovro.caltech.edu> <20090603151905.b191e4b0.kim.phillips@freescale.com> Message-ID: <20090603204605.GD7292@ovro.caltech.edu> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Wed, Jun 03, 2009 at 03:19:05PM -0500, Kim Phillips wrote: > On Wed, 3 Jun 2009 10:50:25 -0700 > Ira Snyder wrote: > > > On Tue, Jun 02, 2009 at 06:08:17PM -0500, Kim Phillips wrote: > > > On Tue, 2 Jun 2009 15:19:18 -0700 > > > Ira Snyder wrote: > > > > > > > On Tue, Jun 02, 2009 at 02:25:03PM -0700, Ira Snyder wrote: > > > > > > > > > > > > And what is the SICRH[30-31]? > > > > > > Did you have the matching settings for GMII with 3.3V? > > > > > > > > > > > > > > > > => md e0000118 1 > > > > > e0000118: 00000002 .... > > > > > > > > > > This looks wrong. The MPC8349EMDS board has the exact same setting in > > > > > that register. Writing 0x0 to the SICRH register did not cause the > > > > > problem to go away. > > ok this... > > > > > > > > > > > > > > The MPC8349EMDS config has had that setting since it was imported into > > > > U-Boot. I've copied the relevant part of include/configs/MPC8349EMDS.h > > > > below. > > > > > > > > #define CONFIG_SYS_SICRH SICRH_TSOBI1 > > > > > > > > This seems wrong for the MPC8349EMDS board. I tried setting the register > > > > value to 0x0 by hand on my MPC8349EMDS eval board, and the network still > > > > works as expected. > > > > > > still works or does not work? 100mbit or 1000mbit?? > > > > > > > Network works, both 100 and 1000 mbit. > > and this seeming contradiction lead to my source of confusion. > > What I think is going on is that you're setting SICRH to 0 on your > custom board and it still has its network problems, and setting it to 0 > on the original MPC8349E-MDS board makes no difference - networking > works with it set to both 0 and 2. ok. > Yes, that is exactly correct. Sorry for my poor choice of words earlier. > > > > Is this a bug in the MPC8349EMDS config? > > > > > > It might be. Another thing that changed wrt that area was commit > > > 846f1574. Assuming this is all still clear to me, perhaps what that > > > patch does should be made 8349-revision dependent? > > > > > > > My MPC8349EMDS reference manual says that bits 28-29 should be > > preserved, which is exactly what the commit message states. > > > > I don't see a problem with commit 846f1574 at all. The bug is that SICRH > > is set to SICRH_TSOBI1 (0x2), which changes the TSEC1 output buffer > > parameters to RGMII/RTBI mode. > > yeah my bad, I miscalculated which bits that commit was masking. > > > The MPC8349EMDS's PHY's are both in GMII mode, the do not use RGMII/RTBI > > or any of the other reduced pin count interfaces. Therefore, I think the > > bit should be cleared, and SICRH should be set to 0x0. > > technically BCSR5 holds the reduced mode MII setting (set via SW4). The > default is GMII, but, as in the case of the 8360 MDS, networking didn't > work out of the box with the default switch settings. > > > Even if I'm wrong, then the bits for both TSEC1 and TSEC2 should be the > > same. Right now, TSEC1 has the RGMII/RTBI output parameters, and TSEC2 > > has the GMII output parameters. > > > > In practice, this doesn't seem to make a difference on the MPC8349EMDS > > eval board. Both settings work without any errors. For people like me, > > who are copying an existing board port to a similar board, it would be > > nice if it was correct. > > granted. I'm betting the sbc8349 and tqm834x just copied the setting > from the MDS code, so those should get 0 too. Board maintainers, > please test: > > diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h > index 3c57403..2d2799e 100644 > --- a/include/configs/MPC8349EMDS.h > +++ b/include/configs/MPC8349EMDS.h > @@ -598,7 +598,7 @@ > #define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) > > /* System IO Config */ > -#define CONFIG_SYS_SICRH SICRH_TSOBI1 > +#define CONFIG_SYS_SICRH 0 > #define CONFIG_SYS_SICRL SICRL_LDP_A > > #define CONFIG_SYS_HID0_INIT 0x000000000 I can ACK this board. I've run the following combinations on my MPC8349EMDS eval board. All of the configurations worked perfectly. U-Boot, PCI Host mode, 1000 mbit U-Boot, PCI Host mode, 100 mbit U-Boot, PCI Agent mode, 1000 mbit U-Boot, PCI Agent mode, 100 mbit Linux, PCI Host mode, 1000 mbit Linux, PCI Host mode, 100 mbit Thanks for looking at this! Ira