From: Jean-Christophe PLAGNIOL-VILLARD Date: Sat, 18 Jul 2009 23:13:22 +0200 Subject: [U-Boot] [PATCH 03/03 v3] Add support for Olimex SAM9-L9260 SBC In-Reply-To: <200907151900.16519.dinuxbg@gmail.com> References: <200907151856.24888.dinuxbg@gmail.com> <200907151900.16519.dinuxbg@gmail.com> Message-ID: <20090718211322.GE16951@game.jcrosoft.org> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On 19:00 Wed 15 Jul , Dimitar Dimitrov wrote: > The SAM9-L9260 board support is based on code for AT91SAM9260EK. Networking > is missing and will be added after the MACB support for AT91 boards is > fixed to comply with U-Boot guide-lines. > > Signed-off-by: Dimitar Dimitrov > --- same as 9261 could you regenerate it with git format-patch -M -B -C > MAINTAINERS | 1 + > MAKEALL | 1 + > Makefile | 17 +++ > board/olimex/sam9_l9260/Makefile | 56 +++++++++ > board/olimex/sam9_l9260/config.mk | 1 + > board/olimex/sam9_l9260/led.c | 41 +++++++ > board/olimex/sam9_l9260/partition.c | 40 +++++++ > board/olimex/sam9_l9260/sam9_l9260.c | 111 ++++++++++++++++++ > include/configs/sam9_l9260.h | 214 ++++++++++++++++++++++++++++++++++ > + > +#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ > + > +#define AT91_CPU_NAME "AT91SAM9260" no-need please remove > +#define CONFIG_AT91SAM9260 1 /* It's an Atmel AT91SAM9260 SoC*/ > +#define CONFIG_SAM9_L9260 1 /* on an SAM9_L9260 Board */ > + > +#define CONFIG_ARCH_CPU_INIT > +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ > + > +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ > +#define CONFIG_SETUP_MEMORY_TAGS 1 > +#define CONFIG_INITRD_TAG 1 > + > +#define CONFIG_SKIP_LOWLEVEL_INIT > +#define CONFIG_SKIP_RELOCATE_UBOOT > + > +/* > + * Hardware drivers > + */ > +#define CONFIG_ATMEL_USART 1 > +#undef CONFIG_USART0 > +#undef CONFIG_USART1 > +#undef CONFIG_USART2 > +#define CONFIG_USART3 1 /* USART 3 is DBGU */ > + > +/* LED */ > +#define CONFIG_AT91_LED > +#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */ > +#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */ please fix the indent > + > +#define CONFIG_BOOTDELAY 3 > + > +/* > + * BOOTP options > + */ > +#define CONFIG_BOOTP_BOOTFILESIZE 1 > +#define CONFIG_BOOTP_BOOTPATH 1 > +#define CONFIG_BOOTP_GATEWAY 1 > +#define CONFIG_BOOTP_HOSTNAME 1 > + > +#define CONFIG_BAUDRATE 115200 > +#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } > + > +#define CONFIG_SYS_PROMPT "U-Boot> " > +#define CONFIG_SYS_CBSIZE 256 > +#define CONFIG_SYS_MAXARGS 16 > +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) > +#define CONFIG_SYS_LONGHELP 1 > +#define CONFIG_CMDLINE_EDITING 1 > + > +#define ROUND(A, B) (((A) + (B)) & ~((B) - 1)) no-need please remove > +/* > + * Size of malloc() pool > + */ Best Regards, J.