From: Matt Waddel Date: Mon, 14 Sep 2009 15:43:28 -0600 Subject: [U-Boot] [PATCH] TI: DaVinci DM365: Enabling net support on DM365 In-Reply-To: <1252955798-31840-1-git-send-email-s-paulraj@ti.com> References: <1252955798-31840-1-git-send-email-s-paulraj@ti.com> Message-ID: <200909141543.28989.mwaddel@control4.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi Sandeep, Is there another part to this patch still coming or did I miss a patch along the way? This patch as-is doesn't compile: ... dm365evm.c: In function ?board_eth_init?: dm365evm.c:47: error: ?GIO_DIR01? undeclared (first use in this function) dm365evm.c:47: error: (Each undeclared identifier is reported only once dm365evm.c:47: error: for each function it appears in.) dm365evm.c:52: error: ?GIO_OUT_DATA01? undeclared (first use in this function) Best regards, Matt On Monday 14 September 2009 01:16:38 pm s-paulraj at ti.com wrote: > From: Sandeep Paulraj > > This patch enables EMAC on the DM365 EVM. > > Signed-off-by: Sandeep Paulraj > --- > board/davinci/dm365evm/dm365evm.c | 38 +++++++++++++++++++++++++++++++++++++ > 1 files changed, 38 insertions(+), 0 deletions(-) > > diff --git a/board/davinci/dm365evm/dm365evm.c b/board/davinci/dm365evm/dm365evm.c > index 99392b3..2092324 100644 > --- a/board/davinci/dm365evm/dm365evm.c > +++ b/board/davinci/dm365evm/dm365evm.c > @@ -17,9 +17,11 @@ > > #include > #include > +#include > #include > #include > #include > +#include > #include "../common/misc.h" > > DECLARE_GLOBAL_DATA_PTR; > @@ -32,6 +34,42 @@ int board_init(void) > return 0; > } > > +#ifdef CONFIG_DRIVER_TI_EMAC > +int board_eth_init(bd_t *bis) > +{ > + uint8_t eeprom_enetaddr[6]; > + int i; > + > + /* Configure PINMUX 3 to enable EMAC pins */ > + writel((readl(PINMUX3) | 0x1affff), PINMUX3); > + > + /* Configure GPIO20 as output */ > + writel((readl(GIO_DIR01) & 0xffefffff), GIO_DIR01); > + > + /* Toggle GPIO 20 */ > + for (i = 0; i < 20; i++) { > + /* GPIO 20 low */ > + writel((readl(GIO_OUT_DATA01) & 0xffefffff), GIO_OUT_DATA01); > + > + udelay(1000); > + > + /* GPIO 20 high */ > + writel((readl(GIO_OUT_DATA01) | 0x00100000), GIO_OUT_DATA01); > + } > + > + /* Configure I2C pins so that EEPROM can be read */ > + writel((readl(PINMUX3) | 0x01400000), PINMUX3); > + > + /* Read Ethernet MAC address from EEPROM */ > + if (dvevm_read_mac_address(eeprom_enetaddr)) > + dv_configure_mac_address(eeprom_enetaddr); > + > + davinci_emac_initialize(); > + > + return 0; > +} > +#endif > + > #ifdef CONFIG_NAND_DAVINCI > static void nand_dm365evm_select_chip(struct mtd_info *mtd, int chip) > { > -- > 1.6.0.4 > > _______________________________________________ > U-Boot mailing list > U-Boot at lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot >