From: computersforpeace@gmail.com (Brian Norris) Date: Tue, 17 Sep 2013 12:29:19 -0700 Subject: [PATCH v2] mtd: atmel_nand: use the common function to get ecc info In-Reply-To: <1379066537-29505-1-git-send-email-josh.wu@atmel.com> References: <1379066537-29505-1-git-send-email-josh.wu@atmel.com> Message-ID: <20130917192919.GO4550@ld-irv-0074.broadcom.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hi Josh, On Fri, Sep 13, 2013 at 06:02:17PM +0800, Josh Wu wrote: > Atmel nand will check ONFI ecc information when config the PMECC parameters. > Since commit: 10c86babfb > (mtd: get the ECC info from the parameter page for ONFI nand) > > introduced the ecc_strength_ds & ecc_step_ds and initialized them during > ONFI detecting. > So we can use them directly and remove our own get_onfi_ecc_param function. > > Signed-off-by: Josh Wu > --- > v1 --> v2: > 1. updated the refered commit id as it is changed when merged in mainline. > 2. refined the commit message > > drivers/mtd/nand/atmel_nand.c | 36 ++++-------------------------------- > 1 file changed, 4 insertions(+), 32 deletions(-) > > diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c > index 060feea..6502247 100644 > --- a/drivers/mtd/nand/atmel_nand.c > +++ b/drivers/mtd/nand/atmel_nand.c > @@ -1062,30 +1062,6 @@ static void atmel_pmecc_core_init(struct mtd_info *mtd) > } > > /* > - * Get ECC requirement in ONFI parameters, returns -1 if ONFI > - * parameters is not supported. > - * return 0 if success to get the ECC requirement. > - */ > -static int get_onfi_ecc_param(struct nand_chip *chip, > - int *ecc_bits, int *sector_size) > -{ > - *ecc_bits = *sector_size = 0; > - > - if (chip->onfi_params.ecc_bits == 0xff) > - /* TODO: the sector_size and ecc_bits need to be find in > - * extended ecc parameter, currently we don't support it. > - */ > - return -1; > - > - *ecc_bits = chip->onfi_params.ecc_bits; > - > - /* The default sector size (ecc codeword size) is 512 */ > - *sector_size = 512; > - > - return 0; > -} > - > -/* > * Get ecc requirement from ONFI parameters ecc requirement. > * If pmecc-cap, pmecc-sector-size in DTS are not specified, this function > * will set them according to ONFI ecc requirement. Otherwise, use the > @@ -1096,19 +1072,15 @@ static int pmecc_choose_ecc(struct atmel_nand_host *host, > int *cap, int *sector_size) > { > /* Get ECC requirement from ONFI parameters */ > - *cap = *sector_size = 0; > if (host->nand_chip.onfi_version) { > - if (!get_onfi_ecc_param(&host->nand_chip, cap, sector_size)) > - dev_info(host->dev, "ONFI params, minimum required ECC: %d bits in %d bytes\n", > + *cap = host->nand_chip.ecc_strength_ds; > + *sector_size = host->nand_chip.ecc_step_ds; The nand_chip.ecc_{strength,step}_ds values are no longer specific to ONFI; they may be included in the full-ID table as well. So this might be better written as: if (host->nand_chip.ecc_strength_ds) { *cap = host->nand_chip.ecc_strength_ds; *sector_size = host->nand_chip.ecc_step_ds; // ... } > + dev_info(host->dev, "ONFI params, minimum required ECC: %d bits in %d bytes\n", > *cap, *sector_size); > - else > - dev_info(host->dev, "NAND chip ECC reqirement is in Extended ONFI parameter, we don't support yet.\n"); > } else { > - dev_info(host->dev, "NAND chip is not ONFI compliant, assume ecc_bits is 2 in 512 bytes"); > - } > - if (*cap == 0 && *sector_size == 0) { > *cap = 2; > *sector_size = 512; > + dev_info(host->dev, "NAND chip is not ONFI compliant, assume ecc_bits is 2 in 512 bytes"); You would also want to change this message to longer be about ONFI. Maybe "cannot detect minimum ECC requirements; assuming 2-bit correction per 512 bytes"? > } > > /* If dts file doesn't specify then use the one in ONFI parameters */ Brian