Date: Wed, 18 Feb 2015 19:49:43 +0100 From: Gilles Chanteperdrix Message-ID: <20150218184943.GH30317@hermes.click-hack.org> References: <54E4D14E.1060104@siemens.com> <20150218175507.GD30317@hermes.click-hack.org> <54E4D61B.1020006@siemens.com> <20150218181334.GE30317@hermes.click-hack.org> <54E4D835.1040204@siemens.com> <20150218182632.GG30317@hermes.click-hack.org> <54E4DDEA.3060909@siemens.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: <54E4DDEA.3060909@siemens.com> Subject: Re: [Xenomai] arm: Late delivery of pending Linux signals? List-Id: Discussions about the Xenomai project List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , To: Jan Kiszka Cc: Xenomai On Wed, Feb 18, 2015 at 07:46:02PM +0100, Jan Kiszka wrote: > On 2015-02-18 19:26, Gilles Chanteperdrix wrote: > > On Wed, Feb 18, 2015 at 07:21:41PM +0100, Jan Kiszka wrote: > >> On 2015-02-18 19:13, Gilles Chanteperdrix wrote: > >>> On Wed, Feb 18, 2015 at 07:12:43PM +0100, Jan Kiszka wrote: > >>>> On 2015-02-18 18:55, Gilles Chanteperdrix wrote: > >>>>> On Wed, Feb 18, 2015 at 06:52:14PM +0100, Jan Kiszka wrote: > >>>>>> Hi Gilles, > >>>>>> > >>>>>> I noticed on ARM (AM335 TI board) that the SIGDEBUG if the related test > >>>>>> apparently only gets delivered to the receiver after it invokes a > >>>>>> syscall, not on return from its secondary mode migration. Therefore the > >>>>>> page fault test of the sigdebug smokey test fails (tested with Xenomai > >>>>>> 3), and I bet the watchdog test as well. Is this a known limitation? > >>>>> > >>>>> Xenomai 2.6 sigdebug works fine on omap3 (very near from an > >>>> > >>>> Will try 2.6 next. > >>>> > >>>>> arm33xx). That being said, the AM3xx port is not part of the main > >>>>> line I-pipe, and based on a non mainline kernel, so it is difficult > >>>>> for me to answer this question. > >>>> > >>>> Then I'm possibly not building all recommended bits - I'm on 3.14 I-pipe > >>>> upstream. That seems to work fine in general. Which version are you > >>>> referring to? > >>> > >>> The one documented in arm/patches/README > >> > >> https://github.com/RobertCNelson/linux-dev/commits/am33x-v3.8? There is > >> nothing explicitly stated regarding the AM3xx board, just that reference > >> in the context of the Beaglebone. > >> > >> Anyway, I thought that syscall and exception handling should not be > >> dependent on board patches, should they? > > > > If you had been using a Linux fork (which I assumed you did, > > because you mentioned a processor which is not mainline officially), > > it would have been very possible for the Linux fork you used to > > break the changes in entry.S due to a bad conflict resolution. > > Linux forks very often tend to push changes in generic code even > > though they should not. > > The TI AM335x (Cortex-A8) comes with full mainline support, even for > 3.14. That's probably why vanilla I-pipe 3.14 works for us. > > Against all odds, I just got Debian installed into an Integrator/CP > machine model. Let's see if I can debug the issue that way. But I will > keep porting I-pipe to the Versatile Express in mind. If you have an ARM board, why going over all these contorsions? Why not simply enabling the I-pipe tracer and looking at what happens when you observe the problem you observe ? -- Gilles.