From: Mark D Rustad Date: Thu, 30 Jul 2015 17:20:10 -0700 Subject: [Intel-wired-lan] [PATCH V3 06/13] ixgbe: Enable bit-banging mode on X550 In-Reply-To: <20150731001845.112031.6979.stgit@mdrustad-wks.jf.intel.com> References: <20150731001845.112031.6979.stgit@mdrustad-wks.jf.intel.com> Message-ID: <20150731002010.112031.42695.stgit@mdrustad-wks.jf.intel.com> MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: intel-wired-lan@osuosl.org List-ID: Set the bit banging mode in the hardware when performing bit banging I2C operations on X550. Also control the output enable on both the clock and data lines. Signed-off-by: Mark Rustad --- drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 65 +++++++++++++++++++++++++- 1 file changed, 63 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c index f342174a4840..d334011f09d1 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c @@ -1940,11 +1940,14 @@ s32 ixgbe_write_i2c_byte_generic_unlocked(struct ixgbe_hw *hw, u8 byte_offset, * @hw: pointer to hardware structure * * Sets I2C start condition (High -> Low on SDA while SCL is High) + * Set bit-bang mode on X550 hardware. **/ static void ixgbe_i2c_start(struct ixgbe_hw *hw) { u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); + i2cctl |= IXGBE_I2C_BB_EN(hw); + /* Start condition must begin with data and clock high */ ixgbe_set_i2c_data(hw, &i2cctl, 1); ixgbe_raise_i2c_clk(hw, &i2cctl); @@ -1969,10 +1972,15 @@ static void ixgbe_i2c_start(struct ixgbe_hw *hw) * @hw: pointer to hardware structure * * Sets I2C stop condition (Low -> High on SDA while SCL is High) + * Disables bit-bang mode and negates data output enable on X550 + * hardware. **/ static void ixgbe_i2c_stop(struct ixgbe_hw *hw) { u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); + u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); + u32 clk_oe_bit = IXGBE_I2C_CLK_OE_N_EN(hw); + u32 bb_en_bit = IXGBE_I2C_BB_EN(hw); /* Stop condition must begin with data low and clock high */ ixgbe_set_i2c_data(hw, &i2cctl, 0); @@ -1985,6 +1993,13 @@ static void ixgbe_i2c_stop(struct ixgbe_hw *hw) /* bus free time between stop and start (4.7us)*/ udelay(IXGBE_I2C_T_BUF); + + if (bb_en_bit || data_oe_bit || clk_oe_bit) { + i2cctl &= ~bb_en_bit; + i2cctl |= data_oe_bit | clk_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); + IXGBE_WRITE_FLUSH(hw); + } } /** @@ -2032,6 +2047,7 @@ static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data) /* Release SDA line (set high) */ i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); i2cctl |= IXGBE_I2C_DATA_OUT(hw); + i2cctl |= IXGBE_I2C_DATA_OE_N_EN(hw); IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); IXGBE_WRITE_FLUSH(hw); @@ -2046,15 +2062,21 @@ static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data) **/ static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw) { + u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); s32 status = 0; u32 i = 0; u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); u32 timeout = 10; bool ack = true; + if (data_oe_bit) { + i2cctl |= IXGBE_I2C_DATA_OUT(hw); + i2cctl |= data_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); + IXGBE_WRITE_FLUSH(hw); + } ixgbe_raise_i2c_clk(hw, &i2cctl); - /* Minimum high period of clock is 4us */ udelay(IXGBE_I2C_T_HIGH); @@ -2092,7 +2114,14 @@ static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw) static s32 ixgbe_clock_in_i2c_bit(struct ixgbe_hw *hw, bool *data) { u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); + u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); + if (data_oe_bit) { + i2cctl |= IXGBE_I2C_DATA_OUT(hw); + i2cctl |= data_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); + IXGBE_WRITE_FLUSH(hw); + } ixgbe_raise_i2c_clk(hw, &i2cctl); /* Minimum high period of clock is 4us */ @@ -2147,13 +2176,20 @@ static s32 ixgbe_clock_out_i2c_bit(struct ixgbe_hw *hw, bool data) * @i2cctl: Current value of I2CCTL register * * Raises the I2C clock line '0'->'1' + * Negates the I2C clock output enable on X550 hardware. **/ static void ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) { + u32 clk_oe_bit = IXGBE_I2C_CLK_OE_N_EN(hw); u32 i = 0; u32 timeout = IXGBE_I2C_CLOCK_STRETCHING_TIMEOUT; u32 i2cctl_r = 0; + if (clk_oe_bit) { + *i2cctl |= clk_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); + } + for (i = 0; i < timeout; i++) { *i2cctl |= IXGBE_I2C_CLK_OUT(hw); IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); @@ -2173,11 +2209,13 @@ static void ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) * @i2cctl: Current value of I2CCTL register * * Lowers the I2C clock line '1'->'0' + * Asserts the I2C clock output enable on X550 hardware. **/ static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) { *i2cctl &= ~IXGBE_I2C_CLK_OUT(hw); + *i2cctl &= ~IXGBE_I2C_CLK_OE_N_EN(hw); IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); IXGBE_WRITE_FLUSH(hw); @@ -2193,13 +2231,17 @@ static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) * @data: I2C data value (0 or 1) to set * * Sets the I2C data bit + * Asserts the I2C data output enable on X550 hardware. **/ static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data) { + u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); + if (data) *i2cctl |= IXGBE_I2C_DATA_OUT(hw); else *i2cctl &= ~IXGBE_I2C_DATA_OUT(hw); + *i2cctl &= ~data_oe_bit; IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); IXGBE_WRITE_FLUSH(hw); @@ -2207,6 +2249,14 @@ static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data) /* Data rise/fall (1000ns/300ns) and set-up time (250ns) */ udelay(IXGBE_I2C_T_RISE + IXGBE_I2C_T_FALL + IXGBE_I2C_T_SU_DATA); + if (!data) /* Can't verify data in this case */ + return 0; + if (data_oe_bit) { + *i2cctl |= data_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); + IXGBE_WRITE_FLUSH(hw); + } + /* Verify data was set correctly */ *i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); if (data != ixgbe_get_i2c_data(hw, i2cctl)) { @@ -2223,9 +2273,19 @@ static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data) * @i2cctl: Current value of I2CCTL register * * Returns the I2C data bit value + * Negates the I2C data output enable on X550 hardware. **/ static bool ixgbe_get_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl) { + u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); + + if (data_oe_bit) { + *i2cctl |= data_oe_bit; + IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); + IXGBE_WRITE_FLUSH(hw); + udelay(IXGBE_I2C_T_FALL); + } + if (*i2cctl & IXGBE_I2C_DATA_IN(hw)) return true; return false; @@ -2240,10 +2300,11 @@ static bool ixgbe_get_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl) **/ static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw) { - u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); + u32 i2cctl; u32 i; ixgbe_i2c_start(hw); + i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); ixgbe_set_i2c_data(hw, &i2cctl, 1);