From: Andre Przywara Date: Wed, 13 Feb 2019 10:14:15 +0000 Subject: [U-Boot] [PATCH 07/10] spi: sun4: Add A31 spi controller support In-Reply-To: References: <20190209131500.29954-1-jagan@amarulasolutions.com> <20190209131500.29954-8-jagan@amarulasolutions.com> <8f578f7e-f2fb-4fd1-2ff2-f32c80e8c70f@arm.com> Message-ID: <20190213101415.3976850c@donnerap.cambridge.arm.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable To: u-boot@lists.denx.de On Wed, 13 Feb 2019 11:20:11 +0800 Chen-Yu Tsai wrote: Hi Chen-Yu, > On Wed, Feb 13, 2019 at 9:21 AM Andr=C3=A9 Przywara wrote: > > > > On 09/02/2019 13:14, Jagan Teki wrote: =20 > > > Add A31 spi controller support for existing sun4i_spi driver via driv= er > > > data, this would simply add A31 register along with proper register b= its > > > via enum sets. > > > > > > Signed-off-by: Jagan Teki > > > --- > > > drivers/spi/Kconfig | 4 +- > > > drivers/spi/sun4i_spi.c | 84 +++++++++++++++++++++++++++++++++++++++= +- > > > 2 files changed, 85 insertions(+), 3 deletions(-) > > > > > > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig > > > index ac7fbab841..15207d23c1 100644 > > > --- a/drivers/spi/Kconfig > > > +++ b/drivers/spi/Kconfig > > > @@ -223,9 +223,9 @@ config STM32_QSPI > > > this ST IP core. > > > > > > config SUN4I_SPI > > > - bool "Allwinner A10 SoCs SPI controller" > > > + bool "Allwinner A10/A31 SoCs SPI controller" > > > help > > > - SPI driver for Allwinner sun4i, sun5i and sun7i SoCs > > > + This enables using the SPI controller on the Allwinner A10/A3= 1 SoCs. > > > > > > config TEGRA114_SPI > > > bool "nVidia Tegra114 SPI driver" > > > diff --git a/drivers/spi/sun4i_spi.c b/drivers/spi/sun4i_spi.c > > > index aeed68764c..36f2215f7d 100644 > > > --- a/drivers/spi/sun4i_spi.c > > > +++ b/drivers/spi/sun4i_spi.c > > > @@ -24,6 +24,7 @@ > > > #include > > > #include > > > #include > > > +#include > > > #include > > > > > > #include > > > @@ -84,6 +85,18 @@ > > > #define SUN4I_FIFO_STA_TF_CNT_MASK 0x7f > > > #define SUN4I_FIFO_STA_TF_CNT_BITS 16 > > > > > > +/* sun6i spi registers */ > > > +#define SUN6I_GBL_CTL_REG 0x04 > > > +#define SUN6I_TFR_CTL_REG 0x08 > > > +#define SUN6I_FIFO_CTL_REG 0x18 > > > +#define SUN6I_FIFO_STA_REG 0x1c > > > +#define SUN6I_CLK_CTL_REG 0x24 > > > +#define SUN6I_BURST_CNT_REG 0x30 > > > +#define SUN6I_XMIT_CNT_REG 0x34 > > > +#define SUN6I_BURST_CTL_REG 0x38 > > > +#define SUN6I_TXDATA_REG 0x200 > > > +#define SUN6I_RXDATA_REG 0x300 > > > + > > > #define SUN4I_SPI_MAX_RATE 24000000 > > > #define SUN4I_SPI_MIN_RATE 3000 > > > #define SUN4I_SPI_DEFAULT_RATE 1000000 > > > @@ -106,6 +119,7 @@ enum sun4i_spi_regs { > > > /* sun spi register bits */ > > > enum sun4i_spi_bits { > > > SPI_GCR_TP, > > > + SPI_GCR_SRST, > > > SPI_TCR_CPHA, > > > SPI_TCR_CPOL, > > > SPI_TCR_CS_ACTIVE_LOW, > > > @@ -133,6 +147,7 @@ struct sun4i_spi_platdata { > > > struct sun4i_spi_priv { > > > struct sun4i_spi_variant *variant; > > > struct clk clk_ahb, clk_mod; > > > + struct reset_ctl reset; > > > u32 base_addr; > > > u32 freq; > > > u32 mode; > > > @@ -255,7 +270,10 @@ static int sun4i_spi_parse_pins(struct udevice *= dev) > > > if (pin < 0) > > > break; > > > > > > - sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SPI0); > > > + if (IS_ENABLED(CONFIG_MACH_SUN50I)) > > > + sunxi_gpio_set_cfgpin(pin, SUN50I_GPC_S= PI0); > > > + else > > > + sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SP= I0); > > > sunxi_gpio_set_drv(pin, drive); > > > sunxi_gpio_set_pull(pin, pull); > > > } > > > @@ -271,6 +289,8 @@ static inline int sun4i_spi_set_clock(struct udev= ice *dev, bool enable) > > > if (!enable) { > > > clk_disable(&priv->clk_ahb); > > > clk_disable(&priv->clk_mod); > > > + if (reset_valid(&priv->reset)) > > > + reset_assert(&priv->reset); > > > return 0; > > > } > > > > > > @@ -286,8 +306,18 @@ static inline int sun4i_spi_set_clock(struct ude= vice *dev, bool enable) > > > goto err_ahb; > > > } > > > > > > + if (reset_valid(&priv->reset)) { > > > + ret =3D reset_deassert(&priv->reset); > > > + if (ret) { > > > + dev_err(dev, "failed to deassert reset\n"); > > > + goto err_mod; > > > + } > > > + } > > > + > > > return 0; > > > > > > +err_mod: > > > + clk_disable(&priv->clk_mod); > > > err_ahb: > > > clk_disable(&priv->clk_ahb); > > > return ret; > > > @@ -328,6 +358,12 @@ static int sun4i_spi_probe(struct udevice *bus) > > > return ret; > > > } > > > > > > + ret =3D reset_get_by_index(bus, 0, &priv->reset); > > > + if (ret && ret !=3D -ENOENT) { > > > + dev_err(dev, "failed to get reset\n"); > > > + return ret; > > > + } > > > + > > > sun4i_spi_parse_pins(bus); > > > > > > priv->variant =3D plat->variant; > > > @@ -351,6 +387,10 @@ static int sun4i_spi_claim_bus(struct udevice *d= ev) > > > SUN4I_CTL_ENABLE | SUN4I_CTL_MASTER | > > > variant->bits[SPI_GCR_TP]); > > > > > > + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) > > > + setbits_le32(priv->base_addr + variant->regs[SPI_GCR], > > > + variant->bits[SPI_GCR_SRST]); > > > + =20 > > > > Just a note: This makes the driver only support one class of device, set > > at compile time. Which means we could have used an #ifdef approach from > > the beginning .... > > Can you make this dependent on some bits in variant? That should solve = it. =20 >=20 > I believe the argument for IS_ENABLED from working in the kernel is that > it still gives you compile-time checks, whereas #ifdef doesn't. I see that, but my point was that this series is more complicated than the = simple one I sent yesterday, using compile time decisions[1]. And the #ifdefs there were not guarding any *code* as well, only defines. So I am not against this approach here, I just wanted to point out that des= pite the extra effort of doing runtime choices we will actually fail in doi= ng so anyway. But if I am not mistaken, this is the only place where this is critical, an= d it can be fixed. > Though I believe your ultimate goal is to have one image for all? In that > case checking against the variants at runtime is better. I am not sure we really want to cover *every* Allwinner board with a single= U-Boot image. For my part I am fine if we can cover all 64-bit boards, may= be an extra build for newer (>=3D SUN6I) 32-bit boards. But to be honest th= ose drivers are the least of our problems then ;-) Cheers, Andre. [1] https://lists.denx.de/pipermail/u-boot/2019-February/358502.html