From: Tom Rini Date: Tue, 19 Nov 2019 16:52:30 -0500 Subject: [U-Boot] [PATCHv2 5/5] env: Finish migration of common ENV options In-Reply-To: <54bb624a-5d80-71e9-4c5a-f5bd4aa20851@gmail.com> References: <20191119010210.24477-1-trini@konsulko.com> <20191119010210.24477-5-trini@konsulko.com> <54bb624a-5d80-71e9-4c5a-f5bd4aa20851@gmail.com> Message-ID: <20191119215230.GJ19317@bill-the-cat> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Tue, Nov 19, 2019 at 10:39:18PM +0100, Simon Goldschmidt wrote: > Am 19.11.2019 um 02:02 schrieb Tom Rini:> - In ARMv8 NXP Layerscape > platforms we also need to make use of > > CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. > > - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define > > to 0. > > - Add Kconfig entry for ENV_ADDR. > > - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. > > - Add ENV_xxx_REDUND options that depend on their primary option and > > SYS_REDUNDAND_ENVIRONMENT > > - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR > > for the pre-main-U-Boot environment location. > > - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but > > rather it being non-zero, as it will now be zero by default. > > - Rework the env_offset absolute in env/embedded.o to not use > > CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within > > ENV_IS_IN_FLASH. > > - Migrate all platforms. > > > > Cc: Wolfgang Denk > > Cc: Joe Hershberger > > Cc: Patrick Delaunay > > Cc: uboot-stm32 at st-md-mailman.stormreply.com > > Signed-off-by: Tom Rini > > --- > > > > > diff --git a/include/configs/socfpga_common.h > b/include/configs/socfpga_common.h > > index baa214399ff9..05bfef75c0df 100644 > > --- a/include/configs/socfpga_common.h > > +++ b/include/configs/socfpga_common.h > > @@ -157,21 +157,13 @@ unsigned int cm_get_qspi_controller_clk_hz(void); > > /* > > * U-Boot environment > > */ > > -#if !defined(CONFIG_ENV_SIZE) > > -#define CONFIG_ENV_SIZE (8 * 1024) > > -#endif > > > > /* Environment for SDMMC boot */ > > -#if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET) > > +#if defined(CONFIG_ENV_IS_IN_MMC) > > #define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */ > > -#define CONFIG_ENV_OFFSET (34 * 512) /* just after the GPT */ > > #endif > > > > /* Environment for QSPI boot */ > > -#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET) > > -#define CONFIG_ENV_OFFSET 0x00100000 > > -#define CONFIG_ENV_SECT_SIZE (64 * 1024) > > -#endif > > Removing paragraphs like this one will break configs that haven't made it to > a mainline defconfig. E.g. for socfpga_socrates_defconfig, you can chose for > the ENV to be saved in SPI instead of MMC as the config supports booting > from all sources. > > How do we proceed with such things? I know that might be non-mainline, but I > think throwing this info away is a step-back, not an improvement. > > [And don't get me wrong: this doesn't affect my downstream boards, they > don't save/load env due to secure boot reasons anyway.] So, I would be happy to see follow up series that add default values for locations for various SoCs. That would address the type of problem you're talking about, I believe. I'd be even happier if someone looked at how Zephyr takes a dts file and generates a header and adapt that to a way for us to have some values be read from a dts* file and turned into a define we can use at build time (not just the OF_PLAT data). That would be a real nice step forward :) -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: