From: Soeren Moch Subject: [PATCH v2 8/9] arm64: dts: rockchip: RockPro64: enable wifi module at sdio0 Date: Thu, 12 Dec 2019 00:52:52 +0100 Message-ID: <20191211235253.2539-9-smoch@web.de> References: <20191211235253.2539-1-smoch@web.de> Mime-Version: 1.0 Content-Transfer-Encoding: quoted-printable Return-path: In-Reply-To: <20191211235253.2539-1-smoch@web.de> Sender: netdev-owner@vger.kernel.org To: Kalle Valo , Heiko Stuebner Cc: Soeren Moch , linux-wireless@vger.kernel.org, brcm80211-dev-list.pdl@broadcom.com, brcm80211-dev-list@cypress.com, netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org List-Id: linux-rockchip.vger.kernel.org RockPro64 supports an Ampak AP6359SA based wifi/bt combo module. The BCM4359/9 wifi controller in this module is connected to sdio0, enable this interface. Use the in-band sdio irq instead of the out-of-band wifi_host_wake_l signal since the latter is not working reliably on this board (probably due to it's PCIe WAKE# connection). Signed-off-by: Soeren Moch =2D-- changes in v2: - add comment about irq in commit message Not sure where to place exactly the sdio0 node in the dts because existing sd nodes are not sorted alphabetically. Cc: Heiko Stuebner Cc: Kalle Valo Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list.pdl@broadcom.com Cc: brcm80211-dev-list@cypress.com Cc: netdev@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: linux-kernel@vger.kernel.org =2D-- .../boot/dts/rockchip/rk3399-rockpro64.dts | 21 ++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts b/arch/arm6= 4/boot/dts/rockchip/rk3399-rockpro64.dts index 7f4b2eba31d4..9fa92790d6e0 100644 =2D-- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts @@ -71,13 +71,6 @@ clock-names =3D "ext_clock"; pinctrl-names =3D "default"; pinctrl-0 =3D <&wifi_enable_h>; - - /* - * On the module itself this is one of these (depending - * on the actual card populated): - * - SDIO_RESET_L_WL_REG_ON - * - PDN (power down when low) - */ reset-gpios =3D <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; }; @@ -650,6 +643,20 @@ status =3D "okay"; }; +&sdio0 { + bus-width =3D <4>; + cap-sd-highspeed; + cap-sdio-irq; + disable-wp; + keep-power-in-suspend; + mmc-pwrseq =3D <&sdio_pwrseq>; + non-removable; + pinctrl-names =3D "default"; + pinctrl-0 =3D <&sdio0_bus4 &sdio0_cmd &sdio0_clk>; + sd-uhs-sdr104; + status =3D "okay"; +}; + &sdmmc { bus-width =3D <4>; cap-sd-highspeed; =2D- 2.17.1