From: Simon Guinot Date: Sat, 20 Jun 2020 02:26:58 +0200 Subject: [PATCH v3 4/4] arm: Remove netspace_v2 board In-Reply-To: <20200618174516.239626-5-jagan@amarulasolutions.com> References: <20200618174516.239626-1-jagan@amarulasolutions.com> <20200618174516.239626-5-jagan@amarulasolutions.com> Message-ID: <20200620002658.GZ15254@kw.sim.vm.gnt> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Thu, Jun 18, 2020 at 11:15:16PM +0530, Jagan Teki wrote: > This board has not been converted to CONFIG_DM by the deadline. I am working at converting this board too, along with net2big_v2. Simon > > Remove it. > > Patch-cc: Simon Guinot > Signed-off-by: Jagan Teki > --- > Changes for v3: > - new patch > > arch/arm/mach-kirkwood/Kconfig | 4 - > board/LaCie/netspace_v2/Kconfig | 12 -- > board/LaCie/netspace_v2/MAINTAINERS | 14 -- > board/LaCie/netspace_v2/Makefile | 10 -- > board/LaCie/netspace_v2/kwbimage-is2.cfg | 149 ---------------------- > board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 149 ---------------------- > board/LaCie/netspace_v2/kwbimage.cfg | 149 ---------------------- > board/LaCie/netspace_v2/netspace_v2.c | 120 ----------------- > board/LaCie/netspace_v2/netspace_v2.h | 22 ---- > configs/inetspace_v2_defconfig | 53 -------- > configs/netspace_lite_v2_defconfig | 53 -------- > configs/netspace_max_v2_defconfig | 53 -------- > configs/netspace_mini_v2_defconfig | 48 ------- > configs/netspace_v2_defconfig | 53 -------- > 14 files changed, 889 deletions(-) > delete mode 100644 board/LaCie/netspace_v2/Kconfig > delete mode 100644 board/LaCie/netspace_v2/MAINTAINERS > delete mode 100644 board/LaCie/netspace_v2/Makefile > delete mode 100644 board/LaCie/netspace_v2/kwbimage-is2.cfg > delete mode 100644 board/LaCie/netspace_v2/kwbimage-ns2l.cfg > delete mode 100644 board/LaCie/netspace_v2/kwbimage.cfg > delete mode 100644 board/LaCie/netspace_v2/netspace_v2.c > delete mode 100644 board/LaCie/netspace_v2/netspace_v2.h > delete mode 100644 configs/inetspace_v2_defconfig > delete mode 100644 configs/netspace_lite_v2_defconfig > delete mode 100644 configs/netspace_max_v2_defconfig > delete mode 100644 configs/netspace_mini_v2_defconfig > delete mode 100644 configs/netspace_v2_defconfig > > diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig > index ad6aef45bf..899c079773 100644 > --- a/arch/arm/mach-kirkwood/Kconfig > +++ b/arch/arm/mach-kirkwood/Kconfig > @@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD > bool "KM Kirkwood Board" > select VENDOR_KM > > -config TARGET_NETSPACE_V2 > - bool "LaCie netspace_v2 Board" > - > config TARGET_IB62X0 > bool "ib62x0 Board" > > @@ -77,7 +74,6 @@ source "board/cloudengines/pogo_e02/Kconfig" > source "board/d-link/dns325/Kconfig" > source "board/iomega/iconnect/Kconfig" > source "board/keymile/Kconfig" > -source "board/LaCie/netspace_v2/Kconfig" > source "board/raidsonic/ib62x0/Kconfig" > source "board/Seagate/dockstar/Kconfig" > source "board/Seagate/goflexhome/Kconfig" > diff --git a/board/LaCie/netspace_v2/Kconfig b/board/LaCie/netspace_v2/Kconfig > deleted file mode 100644 > index 930b822dfb..0000000000 > --- a/board/LaCie/netspace_v2/Kconfig > +++ /dev/null > @@ -1,12 +0,0 @@ > -if TARGET_NETSPACE_V2 > - > -config SYS_BOARD > - default "netspace_v2" > - > -config SYS_VENDOR > - default "LaCie" > - > -config SYS_CONFIG_NAME > - default "lacie_kw" > - > -endif > diff --git a/board/LaCie/netspace_v2/MAINTAINERS b/board/LaCie/netspace_v2/MAINTAINERS > deleted file mode 100644 > index 55fd50d4eb..0000000000 > --- a/board/LaCie/netspace_v2/MAINTAINERS > +++ /dev/null > @@ -1,14 +0,0 @@ > -NETSPACE_V2 BOARD > -M: Simon Guinot > -S: Maintained > -F: board/LaCie/netspace_v2/ > -F: include/configs/lacie_kw.h > -F: configs/inetspace_v2_defconfig > -F: configs/netspace_max_v2_defconfig > -F: configs/netspace_v2_defconfig > - > -NETSPACE_LITE_V2 BOARD > -#M: - > -S: Maintained > -F: configs/netspace_lite_v2_defconfig > -F: configs/netspace_mini_v2_defconfig > diff --git a/board/LaCie/netspace_v2/Makefile b/board/LaCie/netspace_v2/Makefile > deleted file mode 100644 > index a6270bdd4b..0000000000 > --- a/board/LaCie/netspace_v2/Makefile > +++ /dev/null > @@ -1,10 +0,0 @@ > -# SPDX-License-Identifier: GPL-2.0+ > -# > -# Copyright (C) 2011 Simon Guinot > -# > -# Based on Kirkwood support: > -# (C) Copyright 2009 > -# Marvell Semiconductor > -# Written-by: Prafulla Wadaskar > - > -obj-y := netspace_v2.o ../common/common.o > diff --git a/board/LaCie/netspace_v2/kwbimage-is2.cfg b/board/LaCie/netspace_v2/kwbimage-is2.cfg > deleted file mode 100644 > index 50f584ae70..0000000000 > --- a/board/LaCie/netspace_v2/kwbimage-is2.cfg > +++ /dev/null > @@ -1,149 +0,0 @@ > -# SPDX-License-Identifier: GPL-2.0+ > -# > -# Copyright (C) 2011 Simon Guinot > -# > -# Based on Kirkwood support: > -# (C) Copyright 2009 > -# Marvell Semiconductor > -# Written-by: Prafulla Wadaskar > -# Refer doc/README.kwbimage for more details about how-to configure > -# and create kirkwood boot image > -# > - > -# Boot Media configurations > -BOOT_FROM spi # Boot from SPI flash > - > -# SOC registers configuration using bootrom header extension > -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed > - > -# Configure RGMII-0 interface pad voltage to 1.8V > -DATA 0xFFD100e0 0x1B1B1B9B > - > -#Dram initalization for SINGLE x16 CL=5 @ 400MHz > -DATA 0xFFD01400 0x43000618 # DDR Configuration register > -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) > -# bit23-14: zero > -# bit24: 1= enable exit self refresh mode on DDR access > -# bit25: 1 required > -# bit29-26: zero > -# bit31-30: 01 > - > -DATA 0xFFD01404 0x35143000 # DDR Controller Control Low > -# bit 4: 0=addr/cmd in smame cycle > -# bit 5: 0=clk is driven during self refresh, we don't care for APX > -# bit 6: 0=use recommended falling edge of clk for addr/cmd > -# bit14: 0=input buffer always powered up > -# bit18: 1=cpu lock transaction enabled > -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 > -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM > -# bit30-28: 3 required > -# bit31: 0=no additional STARTBURST delay > - > -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1) > -# bit7-4: TRCD > -# bit11- 8: TRP > -# bit15-12: TWR > -# bit19-16: TWTR > -# bit20: TRAS msb > -# bit23-21: 0x0 > -# bit27-24: TRRD > -# bit31-28: TRTP > - > -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High) > -# bit6-0: TRFC > -# bit8-7: TR2R > -# bit10-9: TR2W > -# bit12-11: TW2W > -# bit31-13: zero required > - > -DATA 0xFFD01410 0x00000008 # DDR Address Control > -# bit1-0: 00, Cs0width=x8 > -# bit3-2: 10, Cs0size=512Mb > -# bit5-4: 00, Cs2width=nonexistent > -# bit7-6: 00, Cs1size =nonexistent > -# bit9-8: 00, Cs2width=nonexistent > -# bit11-10: 00, Cs2size =nonexistent > -# bit13-12: 00, Cs3width=nonexistent > -# bit15-14: 00, Cs3size =nonexistent > -# bit16: 0, Cs0AddrSel > -# bit17: 0, Cs1AddrSel > -# bit18: 0, Cs2AddrSel > -# bit19: 0, Cs3AddrSel > -# bit31-20: 0 required > - > -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control > -# bit0: 0, OpenPage enabled > -# bit31-1: 0 required > - > -DATA 0xFFD01418 0x00000000 # DDR Operation > -# bit3-0: 0x0, DDR cmd > -# bit31-4: 0 required > - > -DATA 0xFFD0141C 0x00000632 # DDR Mode > -# bit2-0: 2, BurstLen=2 required > -# bit3: 0, BurstType=0 required > -# bit6-4: 4, CL=5 > -# bit7: 0, TestMode=0 normal > -# bit8: 0, DLL reset=0 normal > -# bit11-9: 6, auto-precharge write recovery ???????????? > -# bit12: 0, PD must be zero > -# bit31-13: 0 required > - > -DATA 0xFFD01420 0x00000004 # DDR Extended Mode > -# bit0: 0, DDR DLL enabled > -# bit1: 1, DDR drive strenght reduced > -# bit2: 1, DDR ODT control lsd enabled > -# bit5-3: 000, required > -# bit6: 1, DDR ODT control msb, enabled > -# bit9-7: 000, required > -# bit10: 0, differential DQS enabled > -# bit11: 0, required > -# bit12: 0, DDR output buffer enabled > -# bit31-13: 0 required > - > -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High > -# bit2-0: 111, required > -# bit3 : 1 , MBUS Burst Chop disabled > -# bit6-4: 111, required > -# bit7 : 1 , D2P Latency enabled > -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz > -# bit9 : 0 , no half clock cycle addition to dataout > -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals > -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh > -# bit15-12: 1111 required > -# bit31-16: 0 required > - > -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) > -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) > - > -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 > -DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size > -# bit0: 1, Window enabled > -# bit1: 0, Write Protect disabled > -# bit3-2: 00, CS0 hit selected > -# bit23-4: ones, required > -# bit31-24: 0x07, Size (i.e. 128MB) > - > -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled > -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled > -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled > - > -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) > -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 > -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 > - > -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) > -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above > -# bit3-2: 01, ODT1 active NEVER! > -# bit31-4: zero, required > - > -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control > -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 > -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 > -# bit11-10:1, DQ_ODTSel. ODT select turned on > - > -DATA 0xFFD01480 0x00000001 # DDR Initialization Control > -#bit0=1, enable DDR init upon this register write > - > -# End of Header extension > -DATA 0x0 0x0 > diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg > deleted file mode 100644 > index 092353a06d..0000000000 > --- a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg > +++ /dev/null > @@ -1,149 +0,0 @@ > -# SPDX-License-Identifier: GPL-2.0+ > -# > -# Copyright (C) 2011 Simon Guinot > -# > -# Based on Kirkwood support: > -# (C) Copyright 2009 > -# Marvell Semiconductor > -# Written-by: Prafulla Wadaskar > -# Refer doc/README.kwbimage for more details about how-to configure > -# and create kirkwood boot image > -# > - > -# Boot Media configurations > -BOOT_FROM spi # Boot from SPI flash > - > -# SOC registers configuration using bootrom header extension > -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed > - > -# Configure RGMII-0 interface pad voltage to 1.8V > -DATA 0xFFD100e0 0x1B1B1B9B > - > -#Dram initalization for SINGLE x16 CL=5 @ 400MHz > -DATA 0xFFD01400 0x43000618 # DDR Configuration register > -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) > -# bit23-14: zero > -# bit24: 1= enable exit self refresh mode on DDR access > -# bit25: 1 required > -# bit29-26: zero > -# bit31-30: 01 > - > -DATA 0xFFD01404 0x34143000 # DDR Controller Control Low > -# bit 4: 0=addr/cmd in smame cycle > -# bit 5: 0=clk is driven during self refresh, we don't care for APX > -# bit 6: 0=use recommended falling edge of clk for addr/cmd > -# bit14: 0=input buffer always powered up > -# bit18: 1=cpu lock transaction enabled > -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 > -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM > -# bit30-28: 3 required > -# bit31: 0=no additional STARTBURST delay > - > -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1) > -# bit7-4: TRCD > -# bit11- 8: TRP > -# bit15-12: TWR > -# bit19-16: TWTR > -# bit20: TRAS msb > -# bit23-21: 0x0 > -# bit27-24: TRRD > -# bit31-28: TRTP > - > -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High) > -# bit6-0: TRFC > -# bit8-7: TR2R > -# bit10-9: TR2W > -# bit12-11: TW2W > -# bit31-13: zero required > - > -DATA 0xFFD01410 0x0000DDDD # DDR Address Control > -# bit1-0: 00, Cs0width=x8 > -# bit3-2: 10, Cs0size=512Mb > -# bit5-4: 00, Cs2width=nonexistent > -# bit7-6: 00, Cs1size =nonexistent > -# bit9-8: 00, Cs2width=nonexistent > -# bit11-10: 00, Cs2size =nonexistent > -# bit13-12: 00, Cs3width=nonexistent > -# bit15-14: 00, Cs3size =nonexistent > -# bit16: 0, Cs0AddrSel > -# bit17: 0, Cs1AddrSel > -# bit18: 0, Cs2AddrSel > -# bit19: 0, Cs3AddrSel > -# bit31-20: 0 required > - > -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control > -# bit0: 0, OpenPage enabled > -# bit31-1: 0 required > - > -DATA 0xFFD01418 0x00000000 # DDR Operation > -# bit3-0: 0x0, DDR cmd > -# bit31-4: 0 required > - > -DATA 0xFFD0141C 0x00000632 # DDR Mode > -# bit2-0: 2, BurstLen=2 required > -# bit3: 0, BurstType=0 required > -# bit6-4: 4, CL=5 > -# bit7: 0, TestMode=0 normal > -# bit8: 0, DLL reset=0 normal > -# bit11-9: 6, auto-precharge write recovery ???????????? > -# bit12: 0, PD must be zero > -# bit31-13: 0 required > - > -DATA 0xFFD01420 0x00000004 # DDR Extended Mode > -# bit0: 0, DDR DLL enabled > -# bit1: 1, DDR drive strenght reduced > -# bit2: 1, DDR ODT control lsd enabled > -# bit5-3: 000, required > -# bit6: 1, DDR ODT control msb, enabled > -# bit9-7: 000, required > -# bit10: 0, differential DQS enabled > -# bit11: 0, required > -# bit12: 0, DDR output buffer enabled > -# bit31-13: 0 required > - > -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High > -# bit2-0: 111, required > -# bit3 : 1 , MBUS Burst Chop disabled > -# bit6-4: 111, required > -# bit7 : 1 , D2P Latency enabled > -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz > -# bit9 : 0 , no half clock cycle addition to dataout > -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals > -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh > -# bit15-12: 1111 required > -# bit31-16: 0 required > - > -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) > -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) > - > -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 > -DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size > -# bit0: 1, Window enabled > -# bit1: 0, Write Protect disabled > -# bit3-2: 00, CS0 hit selected > -# bit23-4: ones, required > -# bit31-24: 0x07, Size (i.e. 128MB) > - > -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled > -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled > -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled > - > -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) > -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 > -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 > - > -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) > -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above > -# bit3-2: 01, ODT1 active NEVER! > -# bit31-4: zero, required > - > -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control > -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 > -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 > -# bit11-10:1, DQ_ODTSel. ODT select turned on > - > -DATA 0xFFD01480 0x00000001 # DDR Initialization Control > -#bit0=1, enable DDR init upon this register write > - > -# End of Header extension > -DATA 0x0 0x0 > diff --git a/board/LaCie/netspace_v2/kwbimage.cfg b/board/LaCie/netspace_v2/kwbimage.cfg > deleted file mode 100644 > index 1ed03fa9a9..0000000000 > --- a/board/LaCie/netspace_v2/kwbimage.cfg > +++ /dev/null > @@ -1,149 +0,0 @@ > -# SPDX-License-Identifier: GPL-2.0+ > -# > -# Copyright (C) 2011 Simon Guinot > -# > -# Based on Kirkwood support: > -# (C) Copyright 2009 > -# Marvell Semiconductor > -# Written-by: Prafulla Wadaskar > -# Refer doc/README.kwbimage for more details about how-to configure > -# and create kirkwood boot image > -# > - > -# Boot Media configurations > -BOOT_FROM spi # Boot from SPI flash > - > -# SOC registers configuration using bootrom header extension > -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed > - > -# Configure RGMII-0 interface pad voltage to 1.8V > -DATA 0xFFD100e0 0x1B1B1B9B > - > -#Dram initalization for SINGLE x16 CL=5 @ 400MHz > -DATA 0xFFD01400 0x43000618 # DDR Configuration register > -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) > -# bit23-14: zero > -# bit24: 1= enable exit self refresh mode on DDR access > -# bit25: 1 required > -# bit29-26: zero > -# bit31-30: 01 > - > -DATA 0xFFD01404 0x35143000 # DDR Controller Control Low > -# bit 4: 0=addr/cmd in smame cycle > -# bit 5: 0=clk is driven during self refresh, we don't care for APX > -# bit 6: 0=use recommended falling edge of clk for addr/cmd > -# bit14: 0=input buffer always powered up > -# bit18: 1=cpu lock transaction enabled > -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 > -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM > -# bit30-28: 3 required > -# bit31: 0=no additional STARTBURST delay > - > -DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1) > -# bit7-4: TRCD > -# bit11- 8: TRP > -# bit15-12: TWR > -# bit19-16: TWTR > -# bit20: TRAS msb > -# bit23-21: 0x0 > -# bit27-24: TRRD > -# bit31-28: TRTP > - > -DATA 0xFFD0140C 0x00000A19 # DDR Timing (High) > -# bit6-0: TRFC > -# bit8-7: TR2R > -# bit10-9: TR2W > -# bit12-11: TW2W > -# bit31-13: zero required > - > -DATA 0xFFD01410 0x0000000C # DDR Address Control > -# bit1-0: 00, Cs0width=x8 > -# bit3-2: 11, Cs0size=1Gb > -# bit5-4: 00, Cs2width=nonexistent > -# bit7-6: 00, Cs1size =nonexistent > -# bit9-8: 00, Cs2width=nonexistent > -# bit11-10: 00, Cs2size =nonexistent > -# bit13-12: 00, Cs3width=nonexistent > -# bit15-14: 00, Cs3size =nonexistent > -# bit16: 0, Cs0AddrSel > -# bit17: 0, Cs1AddrSel > -# bit18: 0, Cs2AddrSel > -# bit19: 0, Cs3AddrSel > -# bit31-20: 0 required > - > -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control > -# bit0: 0, OpenPage enabled > -# bit31-1: 0 required > - > -DATA 0xFFD01418 0x00000000 # DDR Operation > -# bit3-0: 0x0, DDR cmd > -# bit31-4: 0 required > - > -DATA 0xFFD0141C 0x00000632 # DDR Mode > -# bit2-0: 2, BurstLen=2 required > -# bit3: 0, BurstType=0 required > -# bit6-4: 4, CL=5 > -# bit7: 0, TestMode=0 normal > -# bit8: 0, DLL reset=0 normal > -# bit11-9: 6, auto-precharge write recovery ???????????? > -# bit12: 0, PD must be zero > -# bit31-13: 0 required > - > -DATA 0xFFD01420 0x00000004 # DDR Extended Mode > -# bit0: 0, DDR DLL enabled > -# bit1: 1, DDR drive strenght reduced > -# bit2: 1, DDR ODT control lsd enabled > -# bit5-3: 000, required > -# bit6: 1, DDR ODT control msb, enabled > -# bit9-7: 000, required > -# bit10: 0, differential DQS enabled > -# bit11: 0, required > -# bit12: 0, DDR output buffer enabled > -# bit31-13: 0 required > - > -DATA 0xFFD01424 0x0000F07F # DDR Controller Control High > -# bit2-0: 111, required > -# bit3 : 1 , MBUS Burst Chop disabled > -# bit6-4: 111, required > -# bit7 : 1 , D2P Latency enabled > -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz > -# bit9 : 0 , no half clock cycle addition to dataout > -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals > -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh > -# bit15-12: 1111 required > -# bit31-16: 0 required > - > -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) > -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) > - > -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 > -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size > -# bit0: 1, Window enabled > -# bit1: 0, Write Protect disabled > -# bit3-2: 00, CS0 hit selected > -# bit23-4: ones, required > -# bit31-24: 0x07, Size (i.e. 128MB) > - > -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled > -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled > -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled > - > -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) > -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 > -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 > - > -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) > -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above > -# bit3-2: 01, ODT1 active NEVER! > -# bit31-4: zero, required > - > -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control > -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 > -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 > -# bit11-10:1, DQ_ODTSel. ODT select turned on > - > -DATA 0xFFD01480 0x00000001 # DDR Initialization Control > -#bit0=1, enable DDR init upon this register write > - > -# End of Header extension > -DATA 0x0 0x0 > diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c > deleted file mode 100644 > index 011cc563d1..0000000000 > --- a/board/LaCie/netspace_v2/netspace_v2.c > +++ /dev/null > @@ -1,120 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * Copyright (C) 2011 Simon Guinot > - * > - * Based on Kirkwood support: > - * (C) Copyright 2009 > - * Marvell Semiconductor > - * Written-by: Prafulla Wadaskar > - */ > - > -#include > -#include > -#include > -#include > -#include > -#include > -#include > -#include > -#include > -#include > - > -#include "netspace_v2.h" > -#include "../common/common.h" > - > -DECLARE_GLOBAL_DATA_PTR; > - > -int board_early_init_f(void) > -{ > - /* Gpio configuration */ > - mvebu_config_gpio(NETSPACE_V2_OE_VAL_LOW, NETSPACE_V2_OE_VAL_HIGH, > - NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH); > - > - /* Multi-Purpose Pins Functionality configuration */ > - static const u32 kwmpp_config[] = { > - MPP0_SPI_SCn, > - MPP1_SPI_MOSI, > - MPP2_SPI_SCK, > - MPP3_SPI_MISO, > - MPP4_NF_IO6, > - MPP5_NF_IO7, > - MPP6_SYSRST_OUTn, > - MPP7_GPO, /* Fan speed (bit 1) */ > - MPP8_TW_SDA, > - MPP9_TW_SCK, > - MPP10_UART0_TXD, > - MPP11_UART0_RXD, > - MPP12_GPO, /* Red led */ > - MPP14_GPIO, /* USB fuse */ > - MPP16_GPIO, /* SATA 0 power */ > - MPP17_GPIO, /* SATA 1 power */ > - MPP18_NF_IO0, > - MPP19_NF_IO1, > - MPP20_SATA1_ACTn, > - MPP21_SATA0_ACTn, > - MPP22_GPIO, /* Fan speed (bit 0) */ > - MPP23_GPIO, /* Fan power */ > - MPP24_GPIO, /* USB mode select */ > - MPP25_GPIO, /* Fan rotation fail */ > - MPP26_GPIO, /* USB vbus-in detection */ > - MPP28_GPIO, /* USB enable vbus-out */ > - MPP29_GPIO, /* Blue led (slow register) */ > - MPP30_GPIO, /* Blue led (command register) */ > - MPP31_GPIO, /* Board power off */ > - MPP32_GPIO, /* Button (0 = Released, 1 = Pushed) */ > - MPP33_GPIO, /* Fan speed (bit 2) */ > - 0 > - }; > - kirkwood_mpp_conf(kwmpp_config, NULL); > - > - return 0; > -} > - > -int board_init(void) > -{ > - /* Machine number */ > - gd->bd->bi_arch_number = CONFIG_MACH_TYPE; > - > - /* Boot parameters address */ > - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; > - > - return 0; > -} > - > -#if defined(CONFIG_MISC_INIT_R) > -int misc_init_r(void) > -{ > -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) > - if (!env_get("ethaddr")) { > - uchar mac[6]; > - if (lacie_read_mac_address(mac) == 0) > - eth_env_set_enetaddr("ethaddr", mac); > - } > -#endif > - return 0; > -} > -#endif > - > -#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) > -/* Configure and initialize PHY */ > -void reset_phy(void) > -{ > -#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2) > - mv_phy_88e1318_init("egiga0", 0); > -#else > - mv_phy_88e1116_init("egiga0", 8); > -#endif > -} > -#endif > - > -#if defined(CONFIG_KIRKWOOD_GPIO) > -/* Return GPIO button status */ > -static int > -do_read_button(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) > -{ > - return kw_gpio_get_value(NETSPACE_V2_GPIO_BUTTON); > -} > - > -U_BOOT_CMD(button, 1, 1, do_read_button, > - "Return GPIO button status 0=off 1=on", ""); > -#endif > diff --git a/board/LaCie/netspace_v2/netspace_v2.h b/board/LaCie/netspace_v2/netspace_v2.h > deleted file mode 100644 > index 2c930171ea..0000000000 > --- a/board/LaCie/netspace_v2/netspace_v2.h > +++ /dev/null > @@ -1,22 +0,0 @@ > -/* SPDX-License-Identifier: GPL-2.0+ */ > -/* > - * Copyright (C) 2011 Simon Guinot > - * > - * Based on Kirkwood support: > - * (C) Copyright 2009 > - * Marvell Semiconductor > - * Written-by: Prafulla Wadaskar > - */ > - > -#ifndef NETSPACE_V2_H > -#define NETSPACE_V2_H > - > -/* GPIO configuration */ > -#define NETSPACE_V2_OE_LOW 0x06004000 > -#define NETSPACE_V2_OE_HIGH 0x00000031 > -#define NETSPACE_V2_OE_VAL_LOW 0x10030000 > -#define NETSPACE_V2_OE_VAL_HIGH 0x00000000 > - > -#define NETSPACE_V2_GPIO_BUTTON 32 > - > -#endif /* NETSPACE_V2_H */ > diff --git a/configs/inetspace_v2_defconfig b/configs/inetspace_v2_defconfig > deleted file mode 100644 > index 6144eb5fad..0000000000 > --- a/configs/inetspace_v2_defconfig > +++ /dev/null > @@ -1,53 +0,0 @@ > -CONFIG_ARM=y > -CONFIG_SYS_DCACHE_OFF=y > -CONFIG_ARCH_CPU_INIT=y > -CONFIG_ARCH_KIRKWOOD=y > -CONFIG_SYS_TEXT_BASE=0x600000 > -CONFIG_TARGET_NETSPACE_V2=y > -CONFIG_ENV_SIZE=0x1000 > -CONFIG_ENV_OFFSET=0x70000 > -CONFIG_ENV_SECT_SIZE=0x10000 > -CONFIG_NR_DRAM_BANKS=2 > -CONFIG_IDENT_STRING=" IS v2" > -CONFIG_SYS_EXTRA_OPTIONS="INETSPACE_V2" > -CONFIG_BOOTDELAY=3 > -CONFIG_USE_BOOTARGS=y > -CONFIG_BOOTARGS="console=ttyS0,115200" > -CONFIG_USE_PREBOOT=y > -CONFIG_CONSOLE_MUX=y > -CONFIG_MISC_INIT_R=y > -# CONFIG_DISPLAY_BOARDINFO is not set > -CONFIG_HUSH_PARSER=y > -CONFIG_SYS_PROMPT="ns2> " > -CONFIG_CMD_EEPROM=y > -CONFIG_CMD_IDE=y > -CONFIG_CMD_I2C=y > -CONFIG_CMD_SF=y > -CONFIG_CMD_USB=y > -# CONFIG_CMD_SETEXPR is not set > -CONFIG_CMD_DHCP=y > -CONFIG_CMD_MII=y > -CONFIG_CMD_PING=y > -CONFIG_CMD_EXT2=y > -CONFIG_CMD_FAT=y > -CONFIG_ISO_PARTITION=y > -CONFIG_EFI_PARTITION=y > -# CONFIG_PARTITION_UUIDS is not set > -CONFIG_OF_CONTROL=y > -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-is2" > -CONFIG_ENV_IS_IN_SPI_FLASH=y > -CONFIG_USE_ENV_SPI_MAX_HZ=y > -CONFIG_ENV_SPI_MAX_HZ=20000000 > -CONFIG_ENV_ADDR=0x70000 > -CONFIG_MVSATA_IDE=y > -# CONFIG_MMC is not set > -CONFIG_SPI_FLASH=y > -CONFIG_SPI_FLASH_MACRONIX=y > -CONFIG_MVGBE=y > -CONFIG_MII=y > -CONFIG_SYS_NS16550=y > -CONFIG_SPI=y > -CONFIG_KIRKWOOD_SPI=y > -CONFIG_USB=y > -CONFIG_USB_EHCI_HCD=y > -CONFIG_USB_STORAGE=y > diff --git a/configs/netspace_lite_v2_defconfig b/configs/netspace_lite_v2_defconfig > deleted file mode 100644 > index c744d2c58e..0000000000 > --- a/configs/netspace_lite_v2_defconfig > +++ /dev/null > @@ -1,53 +0,0 @@ > -CONFIG_ARM=y > -CONFIG_SYS_DCACHE_OFF=y > -CONFIG_ARCH_CPU_INIT=y > -CONFIG_ARCH_KIRKWOOD=y > -CONFIG_SYS_TEXT_BASE=0x600000 > -CONFIG_TARGET_NETSPACE_V2=y > -CONFIG_ENV_SIZE=0x1000 > -CONFIG_ENV_OFFSET=0x70000 > -CONFIG_ENV_SECT_SIZE=0x10000 > -CONFIG_NR_DRAM_BANKS=2 > -CONFIG_IDENT_STRING=" NS v2 Lite" > -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_LITE_V2" > -CONFIG_BOOTDELAY=3 > -CONFIG_USE_BOOTARGS=y > -CONFIG_BOOTARGS="console=ttyS0,115200" > -CONFIG_USE_PREBOOT=y > -CONFIG_CONSOLE_MUX=y > -CONFIG_MISC_INIT_R=y > -# CONFIG_DISPLAY_BOARDINFO is not set > -CONFIG_HUSH_PARSER=y > -CONFIG_SYS_PROMPT="ns2> " > -CONFIG_CMD_EEPROM=y > -CONFIG_CMD_IDE=y > -CONFIG_CMD_I2C=y > -CONFIG_CMD_SF=y > -CONFIG_CMD_USB=y > -# CONFIG_CMD_SETEXPR is not set > -CONFIG_CMD_DHCP=y > -CONFIG_CMD_MII=y > -CONFIG_CMD_PING=y > -CONFIG_CMD_EXT2=y > -CONFIG_CMD_FAT=y > -CONFIG_ISO_PARTITION=y > -CONFIG_EFI_PARTITION=y > -# CONFIG_PARTITION_UUIDS is not set > -CONFIG_OF_CONTROL=y > -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2lite" > -CONFIG_ENV_IS_IN_SPI_FLASH=y > -CONFIG_USE_ENV_SPI_MAX_HZ=y > -CONFIG_ENV_SPI_MAX_HZ=20000000 > -CONFIG_ENV_ADDR=0x70000 > -CONFIG_MVSATA_IDE=y > -# CONFIG_MMC is not set > -CONFIG_SPI_FLASH=y > -CONFIG_SPI_FLASH_MACRONIX=y > -CONFIG_MVGBE=y > -CONFIG_MII=y > -CONFIG_SYS_NS16550=y > -CONFIG_SPI=y > -CONFIG_KIRKWOOD_SPI=y > -CONFIG_USB=y > -CONFIG_USB_EHCI_HCD=y > -CONFIG_USB_STORAGE=y > diff --git a/configs/netspace_max_v2_defconfig b/configs/netspace_max_v2_defconfig > deleted file mode 100644 > index 8602729fcb..0000000000 > --- a/configs/netspace_max_v2_defconfig > +++ /dev/null > @@ -1,53 +0,0 @@ > -CONFIG_ARM=y > -CONFIG_SYS_DCACHE_OFF=y > -CONFIG_ARCH_CPU_INIT=y > -CONFIG_ARCH_KIRKWOOD=y > -CONFIG_SYS_TEXT_BASE=0x600000 > -CONFIG_TARGET_NETSPACE_V2=y > -CONFIG_ENV_SIZE=0x1000 > -CONFIG_ENV_OFFSET=0x70000 > -CONFIG_ENV_SECT_SIZE=0x10000 > -CONFIG_NR_DRAM_BANKS=2 > -CONFIG_IDENT_STRING=" NS Max v2" > -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MAX_V2" > -CONFIG_BOOTDELAY=3 > -CONFIG_USE_BOOTARGS=y > -CONFIG_BOOTARGS="console=ttyS0,115200" > -CONFIG_USE_PREBOOT=y > -CONFIG_CONSOLE_MUX=y > -CONFIG_MISC_INIT_R=y > -# CONFIG_DISPLAY_BOARDINFO is not set > -CONFIG_HUSH_PARSER=y > -CONFIG_SYS_PROMPT="ns2> " > -CONFIG_CMD_EEPROM=y > -CONFIG_CMD_IDE=y > -CONFIG_CMD_I2C=y > -CONFIG_CMD_SF=y > -CONFIG_CMD_USB=y > -# CONFIG_CMD_SETEXPR is not set > -CONFIG_CMD_DHCP=y > -CONFIG_CMD_MII=y > -CONFIG_CMD_PING=y > -CONFIG_CMD_EXT2=y > -CONFIG_CMD_FAT=y > -CONFIG_ISO_PARTITION=y > -CONFIG_EFI_PARTITION=y > -# CONFIG_PARTITION_UUIDS is not set > -CONFIG_OF_CONTROL=y > -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2max" > -CONFIG_ENV_IS_IN_SPI_FLASH=y > -CONFIG_USE_ENV_SPI_MAX_HZ=y > -CONFIG_ENV_SPI_MAX_HZ=20000000 > -CONFIG_ENV_ADDR=0x70000 > -CONFIG_MVSATA_IDE=y > -# CONFIG_MMC is not set > -CONFIG_SPI_FLASH=y > -CONFIG_SPI_FLASH_MACRONIX=y > -CONFIG_MVGBE=y > -CONFIG_MII=y > -CONFIG_SYS_NS16550=y > -CONFIG_SPI=y > -CONFIG_KIRKWOOD_SPI=y > -CONFIG_USB=y > -CONFIG_USB_EHCI_HCD=y > -CONFIG_USB_STORAGE=y > diff --git a/configs/netspace_mini_v2_defconfig b/configs/netspace_mini_v2_defconfig > deleted file mode 100644 > index ba9301de4d..0000000000 > --- a/configs/netspace_mini_v2_defconfig > +++ /dev/null > @@ -1,48 +0,0 @@ > -CONFIG_ARM=y > -CONFIG_SYS_DCACHE_OFF=y > -CONFIG_ARCH_CPU_INIT=y > -CONFIG_ARCH_KIRKWOOD=y > -CONFIG_SYS_TEXT_BASE=0x600000 > -CONFIG_TARGET_NETSPACE_V2=y > -CONFIG_ENV_SIZE=0x1000 > -CONFIG_ENV_OFFSET=0x70000 > -CONFIG_ENV_SECT_SIZE=0x10000 > -CONFIG_NR_DRAM_BANKS=2 > -CONFIG_IDENT_STRING=" NS v2 Mini" > -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_MINI_V2" > -CONFIG_BOOTDELAY=3 > -CONFIG_USE_BOOTARGS=y > -CONFIG_BOOTARGS="console=ttyS0,115200" > -CONFIG_USE_PREBOOT=y > -CONFIG_CONSOLE_MUX=y > -CONFIG_MISC_INIT_R=y > -# CONFIG_DISPLAY_BOARDINFO is not set > -CONFIG_HUSH_PARSER=y > -CONFIG_SYS_PROMPT="ns2> " > -CONFIG_CMD_EEPROM=y > -CONFIG_CMD_IDE=y > -CONFIG_CMD_I2C=y > -CONFIG_CMD_SF=y > -# CONFIG_CMD_SETEXPR is not set > -CONFIG_CMD_DHCP=y > -CONFIG_CMD_MII=y > -CONFIG_CMD_PING=y > -CONFIG_CMD_EXT2=y > -CONFIG_CMD_FAT=y > -CONFIG_EFI_PARTITION=y > -# CONFIG_PARTITION_UUIDS is not set > -CONFIG_OF_CONTROL=y > -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2mini" > -CONFIG_ENV_IS_IN_SPI_FLASH=y > -CONFIG_USE_ENV_SPI_MAX_HZ=y > -CONFIG_ENV_SPI_MAX_HZ=20000000 > -CONFIG_ENV_ADDR=0x70000 > -CONFIG_MVSATA_IDE=y > -# CONFIG_MMC is not set > -CONFIG_SPI_FLASH=y > -CONFIG_SPI_FLASH_MACRONIX=y > -CONFIG_MVGBE=y > -CONFIG_MII=y > -CONFIG_SYS_NS16550=y > -CONFIG_SPI=y > -CONFIG_KIRKWOOD_SPI=y > diff --git a/configs/netspace_v2_defconfig b/configs/netspace_v2_defconfig > deleted file mode 100644 > index 6ba1ef423e..0000000000 > --- a/configs/netspace_v2_defconfig > +++ /dev/null > @@ -1,53 +0,0 @@ > -CONFIG_ARM=y > -CONFIG_SYS_DCACHE_OFF=y > -CONFIG_ARCH_CPU_INIT=y > -CONFIG_ARCH_KIRKWOOD=y > -CONFIG_SYS_TEXT_BASE=0x600000 > -CONFIG_TARGET_NETSPACE_V2=y > -CONFIG_ENV_SIZE=0x1000 > -CONFIG_ENV_OFFSET=0x70000 > -CONFIG_ENV_SECT_SIZE=0x10000 > -CONFIG_NR_DRAM_BANKS=2 > -CONFIG_IDENT_STRING=" NS v2" > -CONFIG_SYS_EXTRA_OPTIONS="NETSPACE_V2" > -CONFIG_BOOTDELAY=3 > -CONFIG_USE_BOOTARGS=y > -CONFIG_BOOTARGS="console=ttyS0,115200" > -CONFIG_USE_PREBOOT=y > -CONFIG_CONSOLE_MUX=y > -CONFIG_MISC_INIT_R=y > -# CONFIG_DISPLAY_BOARDINFO is not set > -CONFIG_HUSH_PARSER=y > -CONFIG_SYS_PROMPT="ns2> " > -CONFIG_CMD_EEPROM=y > -CONFIG_CMD_IDE=y > -CONFIG_CMD_I2C=y > -CONFIG_CMD_SF=y > -CONFIG_CMD_USB=y > -# CONFIG_CMD_SETEXPR is not set > -CONFIG_CMD_DHCP=y > -CONFIG_CMD_MII=y > -CONFIG_CMD_PING=y > -CONFIG_CMD_EXT2=y > -CONFIG_CMD_FAT=y > -CONFIG_ISO_PARTITION=y > -CONFIG_EFI_PARTITION=y > -# CONFIG_PARTITION_UUIDS is not set > -CONFIG_OF_CONTROL=y > -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ns2" > -CONFIG_ENV_IS_IN_SPI_FLASH=y > -CONFIG_USE_ENV_SPI_MAX_HZ=y > -CONFIG_ENV_SPI_MAX_HZ=20000000 > -CONFIG_ENV_ADDR=0x70000 > -CONFIG_MVSATA_IDE=y > -# CONFIG_MMC is not set > -CONFIG_SPI_FLASH=y > -CONFIG_SPI_FLASH_MACRONIX=y > -CONFIG_MVGBE=y > -CONFIG_MII=y > -CONFIG_SYS_NS16550=y > -CONFIG_SPI=y > -CONFIG_KIRKWOOD_SPI=y > -CONFIG_USB=y > -CONFIG_USB_EHCI_HCD=y > -CONFIG_USB_STORAGE=y > -- > 2.25.1 -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: