Received: from foss.arm.com (foss.arm.com [217.140.110.172]) by smtp.subspace.kernel.org (Postfix) with ESMTP id 2A4C93FDD for ; Tue, 1 Feb 2022 01:41:44 +0000 (UTC) Received: from usa-sjc-imap-foss1.foss.arm.com (unknown [10.121.207.14]) by usa-sjc-mx-foss1.foss.arm.com (Postfix) with ESMTP id F1D0D11FB; Mon, 31 Jan 2022 17:41:37 -0800 (PST) Received: from localhost.localdomain (unknown [172.31.20.19]) by usa-sjc-imap-foss1.foss.arm.com (Postfix) with ESMTPSA id 3FD153F73B; Mon, 31 Jan 2022 17:41:36 -0800 (PST) From: Andre Przywara To: Jagan Teki , Tom Rini , Simon Glass Cc: Jernej Skrabec , Samuel Holland , Chen-Yu Tsai , Icenowy Zheng , Jesse Taube , u-boot@lists.denx.de, linux-sunxi@lists.linux.dev Subject: [PATCH v2 1/5] sunxi: move non-essential code out of s_init() Date: Tue, 1 Feb 2022 01:41:12 +0000 Message-Id: <20220201014116.25864-2-andre.przywara@arm.com> X-Mailer: git-send-email 2.14.1 In-Reply-To: <20220201014116.25864-1-andre.przywara@arm.com> References: <20220201014116.25864-1-andre.przywara@arm.com> Precedence: bulk X-Mailing-List: linux-sunxi@lists.linux.dev List-Id: List-Subscribe: List-Unsubscribe: So far all Allwinner based boards were doing some not-so-lowlevel-setup in lowlevel's s_init() routine. This includes the initial clock, timer and pinmux setup, among other things. This is clearly out of the "absolute bare minimum to get started" scope that lowlevel_init.S suggests for this function. Since we have an SPL, which is called right after s_init(), move those calls to our board_init_f() function. As we overwrite this only for the SPL, this has the added benefit of not doing this setup *again* shortly afterwards, when running U-Boot proper. This makes gpio_init() to be called from the SPL only, so pull this code into a CONFIG_SPL_BUILD protected part to avoid build warnings. Reviewed-by: Samuel Holland Reviewed-by: Simon Glass Tested-by: Simon Glass Signed-off-by: Andre Przywara --- arch/arm/mach-sunxi/board.c | 25 ++++++++++++------------- 1 file changed, 12 insertions(+), 13 deletions(-) diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c index 3ef179742c5..c932a293317 100644 --- a/arch/arm/mach-sunxi/board.c +++ b/arch/arm/mach-sunxi/board.c @@ -75,6 +75,7 @@ ulong board_get_usable_ram_top(ulong total_size) } #endif +#ifdef CONFIG_SPL_BUILD static int gpio_init(void) { __maybe_unused uint val; @@ -172,7 +173,6 @@ static int gpio_init(void) return 0; } -#if defined(CONFIG_SPL_BOARD_LOAD_IMAGE) && defined(CONFIG_SPL_BUILD) static int spl_board_load_image(struct spl_image_info *spl_image, struct spl_boot_device *bootdev) { @@ -227,18 +227,6 @@ void s_init(void) "mcr p15, 0, r0, c1, c0, 1\n" ::: "r0"); #endif -#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_H3 - /* Enable non-secure access to some peripherals */ - tzpc_init(); -#endif - - clock_init(); - timer_init(); - gpio_init(); -#if !CONFIG_IS_ENABLED(DM_I2C) - i2c_init_board(); -#endif - eth_init_board(); } #define SUNXI_INVALID_BOOT_SOURCE -1 @@ -335,11 +323,22 @@ u32 spl_boot_device(void) void board_init_f(ulong dummy) { +#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_H3 + /* Enable non-secure access to some peripherals */ + tzpc_init(); +#endif + + clock_init(); + timer_init(); + gpio_init(); + eth_init_board(); + spl_init(); preloader_console_init(); #if CONFIG_IS_ENABLED(I2C) && CONFIG_IS_ENABLED(SYS_I2C_LEGACY) /* Needed early by sunxi_board_init if PMU is enabled */ + i2c_init_board(); i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); #endif sunxi_board_init(); -- 2.17.6