From: Dalon L Westergreen Date: Wed, 13 Feb 2019 14:45:39 -0800 Subject: [U-Boot] [PATCH v8 2/8] ARM: socfpga: Add default FPGA bitstream fitImage for Arria10 SoCDK In-Reply-To: References: <1550067518-2542-1-git-send-email-tien.fong.chee@intel.com> <1550067518-2542-3-git-send-email-tien.fong.chee@intel.com> Message-ID: <2f584adfddbd3f40366aeb5d5f6954373f4735f8.camel@linux.intel.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On Wed, 2019-02-13 at 17:10 +0100, Marek Vasut wrote: > On 2/13/19 3:18 PM, tien.fong.chee at intel.com wrote: > > From: Tien Fong Chee > > > > Add default fitImage file bundling FPGA bitstreams for Arria10. > > > > Signed-off-by: Tien Fong Chee > > > > --- > > > > changes for v8 > > - Changed the FPGA node name to fpga-core and fpga-periph for both core and > > periph bitstreams respectively. > > --- > > board/altera/arria10-socdk/fit_spl_fpga.its | 39 > > +++++++++++++++++++++++++++++ > > 1 file changed, 39 insertions(+) > > create mode 100644 board/altera/arria10-socdk/fit_spl_fpga.its > > > > diff --git a/board/altera/arria10-socdk/fit_spl_fpga.its > > b/board/altera/arria10-socdk/fit_spl_fpga.its > > new file mode 100644 > > index 0000000..8ce175b > > --- /dev/null > > +++ b/board/altera/arria10-socdk/fit_spl_fpga.its > > @@ -0,0 +1,39 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > + /* > > + * Copyright (C) 2019 Intel Corporation > > + * > > + */ > > + > > +/dts-v1/; > > + > > +/ { > > + description = "FIT image with FPGA bistream"; > > + #address-cells = <1>; > > + > > + images { > > + fpga-core at 1 { > > + description = "FPGA core bitstream"; > > + data = /incbin/("../../../ghrd_10as066n2.core.rbf"); > > + type = "fpga"; > > + arch = "arm"; > > + compression = "none"; > > + load = <0x400>; > > Is the load address required ? > > > + }; > > + > > + fpga-periph at 2 { > > + description = "FPGA peripheral bitstream"; > > + data = /incbin/("../../../ghrd_10as066n2.periph.rbf"); > > + type = "fpga"; > > + arch = "arm"; > > + compression = "none"; > > + }; > > + }; > > + > > + configurations { > > + default = "config-1"; > > + config-1 { > > + description = "Boot with FPGA early IO release config"; > > + fpga = "fpga-periph at 2", "fpga-core at 1"; > > Don't you need to load the core first ? No, the periphery is first. This brings up the dram and i/o. --dalon > > > + }; > > + }; > > +}; > > > >