Return-path: Received: from moutng.kundenserver.de ([212.227.17.10]) by mail.linuxtv.org with esmtp (Exim 4.69) (envelope-from ) id 1NNlO1-00059l-6d for linux-dvb@linuxtv.org; Thu, 24 Dec 2009 11:57:45 +0100 Message-ID: <4B334905.1000409@naiadhome.com> Date: Thu, 24 Dec 2009 10:57:09 +0000 From: Peter MIME-Version: 1.0 To: linux-dvb@linuxtv.org Subject: [linux-dvb] Problem tuning frequencyusing Nova S plus Reply-To: linux-media@vger.kernel.org List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: multipart/mixed; boundary="===============2028719069==" Mime-version: 1.0 Sender: linux-dvb-bounces@linuxtv.org Errors-To: linux-dvb-bounces+mchehab=infradead.org@linuxtv.org List-ID: --===============2028719069== Content-Type: text/html; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit I am having a problem tuning to a couple of particular frequencies using a Hauppauge Nova S Plus. There are two transponders very close in frequency and neither of them will give a lock, while other transponders from the same satellite lock just fine.

The satellite is: Intelsat 10 (IS-10) (68.5E) -

and the transponder I am interested in is: 3864.00 H - Txp: 4 - Beam: C DVB-S (QPSK) - 19850 3/4 - NID:65535 - TID:1

I can tune to transponders either side of this, but I fail to get a lock when using dvbtune.

root# dvbtune -f 3864000 -s 19850 -p h -c 3 -cr 3_4
No CA device found, skipping
Using DVB card "Conexant CX24123/CX24109"
Using C-BAND parameters LOF=5150000
tuning DVB-S to Freq: 1286000, Pol:H Srate=19850000, 22kHz tone=off, LNB: 0
Setting only tone OFF and voltage 18V
DISEQC SETTING SUCCEDED
polling....
Getting frontend event
FE_STATUS:
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL
polling....
polling....
polling....

---- give up

Setting the debug=1 on the module I get this in dmesg:
CX24123: cx24123_initfe: init frontend
CX24123: cx24123_set_tone: setting tone off
CX24123: cx24123_set_frontend:
CX24123: cx24123_set_inversion: inversion auto
CX24123: cx24123_set_fec: set FEC to auto
CX24123: cx24123_set_symbolrate: srate=19850000, ratio=0x003ed29a, sample_rate=40444000 sample_gain=1
CX24123: cx24123_pll_tune: frequency=1286000
CX24123: cx24123_pll_writereg: pll writereg called, data=0x00100e3f
CX24123: cx24123_pll_writereg: pll writereg called, data=0x000a0180
CX24123: cx24123_pll_writereg: pll writereg called, data=0x00000201
CX24123: cx24123_pll_writereg: pll writereg called, data=0x001f84f7
CX24123: cx24123_pll_tune: pll tune VCA=1052223, band=513, pll=2065655
CX24123: cx24123_read_ber: BER = 0
CX24123: cx24123_read_signal_strength: Signal strength = 64768
CX24123: cx24123_read_snr: read S/N index = 64135
CX24123: cx24123_read_ber: BER = 0
CX24123: cx24123_read_signal_strength: Signal strength = 64768
CX24123: cx24123_read_snr: read S/N index = 64197

When I tune to a very close adjacent channel I also get a failure:
3863.00 V - Txp: 15 - Beam: CDVB-S (QPSK) - 20600 3/4 - NID:6144 - TID:9

which is only 1 MHz different from the transponder I am interested in, though on a different polarity.

When I tune to an channel some way off I get a lock, for example:
dvbtune -f 3836000 -s 20600 -p v -c 3 -cr 3_4
No CA device found, skipping
Using DVB card "Conexant CX24123/CX24109"
Using C-BAND parameters LOF=5150000
tuning DVB-S to Freq: 1314000, Pol:V Srate=20600000, 22kHz tone=off, LNB: 0
Setting only tone OFF and voltage 13V
DISEQC SETTING SUCCEDED
polling....
Getting frontend event
FE_STATUS:
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Event:  Frequency: 11064000
        SymbolRate: 20600000
        FEC_inner:  3

Bit error rate: 0
Signal strength: 62464
SNR: 65252
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC

I was wondering if anyone had come across a similar problem? I am speculating, but maybe this is interference from an adjacent channel since other channels with wider spacing always work. Interestingly a commercial satellite STB can tune to this transponder without errors, so this does indicate a driver releated buglet.

Are there any cx24123 parameters that could be tweaked to help here, or maybe this is a tuner problem?

Could anyone provide me with the data sheets for the demod and tuner for these cards? I would be happy to dig into this a bit deeper.

Regards

Pete




--===============2028719069== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ linux-dvb users mailing list For V4L/DVB development, please use instead linux-media@vger.kernel.org linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb --===============2028719069==--