From: rogerq@ti.com (Roger Quadros) Date: Thu, 21 Mar 2013 16:12:35 +0200 Subject: [PATCH] ARM: OMAP4: clock: Initialize USB DPLL In-Reply-To: <1363873705-3224-1-git-send-email-rogerq@ti.com> References: <1363873705-3224-1-git-send-email-rogerq@ti.com> Message-ID: <514B1553.6030701@ti.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org +Paul On 03/21/2013 03:48 PM, Roger Quadros wrote: > If the bootloader doesn't configure USB DPLL (e.g. in u-boot, > disable CONFIG_USB_EHCI_OMAP), then we get all sorts of problems > like > - division by zero errors at boot [1] > - USB DPLL fails to enter locked state > - USB EHCI Host is non functional > - Device can't enter OFF mode > > Initializing the USB DPLL fixes all these issues. > > [1] > > [ 0.000000] clock: dpll_usb_ck failed transition to 'locked' > [ 0.000000] Division by zero in kernel. > [ 0.000000] [] (unwind_backtrace+0x0/0xf0) from [] (Ldiv0+0x8/0x10) > [ 0.000000] [] (Ldiv0+0x8/0x10) from [] (clk_divider_set_rate+0x10/0x124) > [ 0.000000] [] (clk_divider_set_rate+0x10/0x124) from [] (clk_change_rate+0x3c/0xb4) > [ 0.000000] [] (clk_change_rate+0x3c/0xb4) from [] (clk_change_rate+0xa0/0xb4) > > Signed-off-by: Roger Quadros > --- > arch/arm/mach-omap2/cclock44xx_data.c | 19 +++++++++++++++++++ > 1 files changed, 19 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c > index bfc46c1..6127bb9 100644 > --- a/arch/arm/mach-omap2/cclock44xx_data.c > +++ b/arch/arm/mach-omap2/cclock44xx_data.c > @@ -53,6 +53,12 @@ > */ > #define OMAP4_DPLL_ABE_DEFFREQ 98304000 > > +/* > + * OMAP4450 TRM Rev X, section "3.6.3.9.5 DPLL_USB Preferred Settings" > + * states it must be at 960MHz > + */ > +#define OMAP4_DPLL_USB_DEFFREQ 960000000 > + > /* Root clocks */ > > DEFINE_CLK_FIXED_RATE(extalt_clkin_ck, CLK_IS_ROOT, 59000000, 0x0); > @@ -1729,6 +1735,19 @@ int __init omap4xxx_clk_init(void) > omap2_clk_disable_autoidle_all(); > > /* > + * Lock USB_DPLL to avoid issues with USB host and OFF mode > + */ > + rc = clk_set_rate(&dpll_usb_ck, OMAP4_DPLL_USB_DEFFREQ); > + if (rc) { > + pr_err("%s: failed to configure DPLL_USB: %d\n", __func__, rc); > + } else { > + rc = clk_set_rate(&dpll_usb_m2_ck, OMAP4_DPLL_USB_DEFFREQ/2); > + if (rc) > + pr_err("%s: failed to configure DPLL_USB_M2: %d\n", > + __func__, rc); > + } > + > + /* > * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power > * state when turning the ABE clock domain. Workaround this by > * locking the ABE DPLL on boot. >