Return-path: Received: from smtp1.ugent.be ([157.193.71.182]) by bombadil.infradead.org with esmtp (Exim 4.80.1 #2 (Red Hat Linux)) id 1XEgTS-0007GM-JG for ath10k@lists.infradead.org; Tue, 05 Aug 2014 15:16:28 +0000 Message-ID: <53E0F52E.3010006@intec.ugent.be> Date: Tue, 05 Aug 2014 17:15:58 +0200 From: Bart Jooris MIME-Version: 1.0 Subject: Re: Performance v/s signal quality graph. References: <53D2E50E.5010205@candelatech.com> In-Reply-To: <53D2E50E.5010205@candelatech.com> List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Reply-To: Bart.Jooris@intec.ugent.be Content-Transfer-Encoding: 7bit Content-Type: text/plain; charset="us-ascii"; Format="flowed" Sender: "ath10k" Errors-To: ath10k-bounces+kvalo=adurom.com@lists.infradead.org To: Ben Greear , ath10k Hi Ben, I enjoyed watching your graph already a few times now ;-) I have a few questions related to your experiment: -about the setup, the cards have 3x3 MIMO so the attenuator has probably also three channels which are attenuated in parallel? -based on the datasheet of the QCA9880 VHT80_MCS9 reception should break around -68dBm. On your graph it breaks around -52dBm, which is not within the described tolerances. Do you have any idea what could be causing this? Is the noise level higher than expected? Or did I made the wrong conclusions? I will try to verify on our setup. -my million dollar question to you is related to the approx. 810Mbps UDP goodput :-) I already did some experiments over 3 coax cables, I noticed the same UDP goodput as over the air, which is around 640Mbps. Watching the sniffer I've noticed MCS=9, Data rate=1299.9 Mbps and block ACKs every (in avg.) 10 frames. So what is the key to the higher goodput? -related to the hot signal, without having proof I've noticed that it is easier to have higher goodputs with a low tx-power set, like 1 dBm. But probably more related to our setup... Which tx-power did you use during your experiments? Would you be able to get the same results (point break around -52dBm) with another tx-power set? Thanks, Bart On 07/26/2014 01:15 AM, Ben Greear wrote: > Some time back, I ran some tests, and someone (sorry, can't remember or find the email) > suggested my signal might be too hot. I was using a 30 db fixed attenuator inline with the SMA > cables. > > I set up a test today with E5 processor system as station, and a fast i7 processor > system as AP, with the two systems cabled through our variable attenuator. Open authentication, > channel 149, other wifi equipment in area on 5ghz was (mostly) idle or powered down. > Kernel is 3.14.13+, latest ath10k CT (10.1.467 based) firmware on both systems > (though I don't think that matters much for throughput tests). 10 virtual stations > configured on station machine, but only one was actively doing traffic. > > Here is a udp download v/s rx-signal graph as the attenuator is stepped from 0 to 95.5 > db attenuation in .5 db steps. > > http://www.candelatech.com/pdfs/ath10k_atten_vs_throughput.pdf > > The rx-signal axis is the left hand side. The green graph is the station's (ie netdev) > rx bps, the black is UDP goodput. > > It seems ath10k (WLE900VX) has no real trouble with hot signals, and runs best between > -15 and -52 rx signal level (as reported by the station device). > > Our systems are not perfectly isolated, so the maximum attenuation is around -85. > > Enjoy, > Ben > -- Bart Jooris Department of Information Technology Internet Based Communication Networks and Services (IBCN) Ghent University - iMinds Gaston Crommenlaan 8 (Bus 201), B-9050 Gent, Belgium E-mail: bart.jooris@intec.UGent.be M: +32 474 59 53 42 Tel. +32 9 33 14900 Fax +32 9 33 14899 _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k