From: marcio at netopen.com.br Date: Fri, 15 Mar 2013 11:46:17 -0700 (PDT) Subject: [U-Boot] AT91SAM9M10 Custom Board U-boot reboot after Wrong Image Format In-Reply-To: <514282C5.4010203@gmail.com> References: <1363177574526-149567.post@n7.nabble.com> <51412754.8070707@gmail.com> <63f3857f52f5657a4a4817c11a38e566@netopen.com.br> <514282C5.4010203@gmail.com> Message-ID: <54a8dde1b2d64623374eb97048f5bbed@netopen.com.br> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi B. Thanks for your attention! >Bad Data CRC don't help. Because, many possible issue will cause this issue. I will provide the log. >Consider you use 16bit NAND flash. Have you define >CONFIG_SYS_NAND_DBW_16 in board configuration header? Yes I did that. Before I include this definition the board did not even try to boot the kernel. >BTW, which bootstrap version do you use? (As I suspect the bootstrap has >enabled for supporting 16bit NAND, so it read u-boot OK) The At91bootstrap indeed loads U-boot OK. The problem is afterward. U-Boot 2012.10-00075-g0362411-dirty (Mar 15 2013 - 11:33:53) U-Boot code: 73F00000 -> 73F370C0 BSS: -> 73F79654 CPU: AT91SAM9G45 Crystal frequency: 12 MHz CPU clock : 400 MHz Master clock : 133.333 MHz dram_init dram_init tam_ram=67108864 testa_ram_readonly: Inicio testa_ram_readonly: Fim monitor len: 00079654 ramsize: 04000000 TLB table at: 73ff0000 Top of RAM usable for U-Boot at: 73ff0000 Reserving 485k for U-Boot at: 73f76000 Reserving 640k for malloc() at: 73ed6000 Reserving 32 Bytes for Board Info at: 73ed5fe0 Reserving 144 Bytes for Global Data at: 73ed5f50 New Stack Pointer is: 73ed5f40 comeca a configurar a DRAM Display DRAM display_dram_config: DRAM: 64 MiB reloca e perde o controle 00000000 relocation Offset is: 00076000 board_init_r: gd=73ed5f50 WARNING: Caches not enabled monitor flash len: 0003C950 Now running in RAM - U-Boot at: 73f76000 NAND: 256 MiB board_init_r: Initialize Environmet env_relocate: Inicio gd=73ed5f50 gd->env_valid=0 Using default environment env_relocate: Fim board_init_r: jumptable board_init_r: jumptable sai In: serial Out: serial Err: serial board_init_r:interrupts board_init_r: initialize board_init_r: main loop ### main_loop entered: bootdelay=3 ### main_loop: bootcmd="nand read 0x70000000 0x200000 0x300000;bootm 0x70000000" Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x200000, size 0x300000 3145728 bytes read: OK * kernel: cmdline image address = 0x70000000 ## Booting kernel from Legacy Image at 70000000 ... Image Name: Linux-2.6.39.4 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3630052 Bytes = 3.5 MiB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! -- View this message in context: http://u-boot.10912.n7.nabble.com/AT91SAM9M10-Custom-Board-U-boot-reboot-after-Wrong-Image-Format-tp149567p149822.html Sent from the U-Boot mailing list archive at Nabble.com.