From: icenowy@aosc.xyz (Icenowy Zheng) Date: Sat, 25 Feb 2017 15:14:02 +0800 Subject: [PATCH] arm64: dts: allwinner: add support for Pinebook In-Reply-To: <20170225070032.35834-1-icenowy@aosc.xyz> References: <20170225070032.35834-1-icenowy@aosc.xyz> Message-ID: <9241341488006842@web3g.yandex.ru> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org 25.02.2017, 15:01, "Icenowy Zheng" : > Pinebook is a A64-based laptop produced by Pine64, with the following > peripherals: > > USB: > - Two external USB ports (one is directly connected to A64's OTG > controller, the other is under a internal hub connected to the host-only > controller.) > - USB HID keyboard and touchpad connected to the internal hub. > - USB UVC camera connected to the internal hub. > > Power-related: > - A DC IN jack connected to AXP803's DCIN pin. > - A Li-Polymer battery connected to AXP803's battery pins. > > Storage: > - An eMMC by Foresee on the main board (in the product revision of the > main board it's designed to be switchable). > - An external MicroSD card slot. > > Display: > - An eDP LCD panel (1366x768) connected via an ANX6345/ANX9807 RGB-eDP > bridge. > - A mini HDMI jack. > > Misc: > - A Hall sensor designed to detect the status of lid, connected to GPIO PH10. > - A headphone jack connected to the SoC's internal codec. > - A BMA223 gravity sensor connected to the SoC's I2C1 bus. (Not > supported yet) > - A debug UART port muxed with one of the USB ports, only available on > product revision of the main board. > > This commit adds basical support for it, with out-of-tree patches for > display support the laptop can be basically usable. > > Signed-off-by: Icenowy Zheng > --- > ?arch/arm64/boot/dts/allwinner/Makefile | 1 + > ?.../boot/dts/allwinner/sun50i-a64-pinebook.dts | 123 +++++++++++++++++++++ > ?2 files changed, 124 insertions(+) > ?create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index bc6f342be59f..893520c39955 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -1,4 +1,5 @@ > ?dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb > ?dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb > > ?always := $(dtb-y) > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts > new file mode 100644 > index 000000000000..2dceba3132b0 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts > @@ -0,0 +1,123 @@ > +/* > + * Copyright (c) 2016 ARM Ltd. > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This library is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This library is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > + > +#include "sun50i-a64.dtsi" > + > +#include Sorry but I missed a line here: #include It's for the switch code for gpio_keys part (it's used to describe the Hall sensor). > + > +/ { > + model = "Pinebook"; > + compatible = "pine64,pinebook", "allwinner,sun50i-a64"; > + > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + > + lid_switch { > + label = "Lid Switch"; > + gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ > + linux,input-type = ; > + linux,code = ; > + linux,can-disable; > + }; > + }; > + > + reg_vcc3v3: vcc3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins>; > + vmmc-supply = <®_vcc3v3>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; > + cd-inverted; > + disable-wp; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins_a>; > + status = "okay"; > +}; > + > +&usb_otg { > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; > -- > 2.11.1