From: Patrick DELAUNAY Date: Thu, 14 May 2020 09:30:16 +0000 Subject: [PATCH v2 00/12] stm32mp1: several board and arch updates In-Reply-To: <20200422122920.19340-1-patrick.delaunay@st.com> References: <20200422122920.19340-1-patrick.delaunay@st.com> Message-ID: <9d92f0ec666f45df980fde2c3dcd4cec@SFHDAG6NODE3.st.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi, > From: Patrick DELAUNAY > Sent: mercredi 22 avril 2020 14:29 > > > It is a V2 for the serie > http://patchwork.ozlabs.org/project/uboot/list/?series=167872 > > Rebased on master branch and after the first reviews: > > [01/16] arm: stm32mp: update dependency for STM32_ETZPC > is already accepted/merged > > [03/16] arm: stm32mp: reset to default environment when serial# change [04/16] > arm: stm32mp: detect U-Boot version used to save environment [11/16] board: > stm32mp1: check env_get result in board_late_init > are dropped > > [05/16] arm: stm32mp: spl: add bsec driver in SPL > this unrelated patch is moved in a separate serie: > "stm32mp1: use OPP information for PLL1 settings in SPL" > > > Changes in v2: > - minor commit message update > - simplify patch after Wolfgang review, as console init alway failed when > drivers can't probe (remove printf after preloader_console_init call) > - use CONFIG_IS_ENABLED(LED) everywhere > - remove debug message and unused return of board_ev1_init > - remove bootdelay configuration after Wolfgang's comment on dropped patch > [11/16] board: stm32mp1: check env_get result in board_late_init > > Christophe Roullier (1): > configs: stm32mp1: activate Ethernet PHY Realtek > > Patrice Chotard (1): > board: stm32mp1: Keep error led ON in case of low power detection > > Patrick Delaunay (10): > arm: stm32mp: remove dependency for STM32KEY > arm: stm32mp: spl: update error management in board_init_f > board: stm32mp1: update management of boot-led > board: stm32mp1: gt9147 IRQ before reset on EV1 > board: stm32mp1: set environment variable fdtfile > board: stm32mp1: remove bootdelay configuration for usb or serial boot > board: stm32mp1: add timeout for I/O compensation ready > gpio: stm32: support gpio ops in SPL > ARM: dts: stm32mp15: use DDR3 files generated by STM32CubeMX > configs: stm32mp1: activate CONFIG_ERRNO_STR > > .../dts/stm32mp15-ddr3-1x4Gb-1066-binG.dtsi | 49 +++++---- > .../dts/stm32mp15-ddr3-2x4Gb-1066-binG.dtsi | 49 +++++---- > arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 4 - > arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 4 - > arch/arm/mach-stm32mp/Kconfig | 2 - > arch/arm/mach-stm32mp/spl.c | 6 +- > board/st/stm32mp1/stm32mp1.c | 102 +++++++++++++----- > configs/stm32mp15_basic_defconfig | 2 + > configs/stm32mp15_trusted_defconfig | 2 + > drivers/gpio/stm32_gpio.c | 7 +- > 10 files changed, 130 insertions(+), 97 deletions(-) > > -- > 2.17.1 For the serie applied to u-boot-stm/master, thanks! Regards Patrick