From: Patrice CHOTARD Date: Thu, 13 Aug 2020 08:08:39 +0000 Subject: [Uboot-stm32] [PATCH] board: stm32mp1: remove board.c In-Reply-To: <7552830a-3c16-79df-0a3d-73b6e4b127e4@st.com> References: <20200730115735.2063-1-patrick.delaunay@st.com> <7552830a-3c16-79df-0a3d-73b6e4b127e4@st.com> Message-ID: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This patch doesn't apply correctly and the sha1 was not the correct one. Nevertheless i update it and applied it on u-boot-stm/master Thanks patrice On 8/13/20 9:45 AM, Patrice CHOTARD wrote: > Hi Patrick > > On 7/30/20 1:57 PM, Patrick Delaunay wrote: >> Remove the file board/st/stm32mp1/board.c which is not more >> compiled since commit 156732cc8939 ("board: stm32mp1: move the >> function board_debug_uart_init in spl.c") >> >> Fixes: 156732cc8939 ("board: stm32mp1: move the function board_debug_uart_init in spl.c") >> Signed-off-by: Patrick Delaunay >> --- >> Issue when initial patch [1] was applied: >> >> diff --git a/board/st/stm32mp1/board.c b/board/st/stm32mp1/board.c >> deleted file mode 100644 >> >> [1] http://patchwork.ozlabs.org/project/uboot/patch/20200525101949.15944-10-patrick.delaunay at st.com/ >> >> >> board/st/stm32mp1/board.c | 36 ------------------------------------ >> 1 file changed, 36 deletions(-) >> delete mode 100644 board/st/stm32mp1/board.c >> >> diff --git a/board/st/stm32mp1/board.c b/board/st/stm32mp1/board.c >> deleted file mode 100644 >> index 00c61c2886..0000000000 >> --- a/board/st/stm32mp1/board.c >> +++ /dev/null >> @@ -1,36 +0,0 @@ >> -// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause >> -/* >> - * Copyright (C) 2018, STMicroelectronics - All Rights Reserved >> - */ >> - >> -#include >> -#include >> -#include >> -#include >> - >> -#ifdef CONFIG_DEBUG_UART_BOARD_INIT >> -void board_debug_uart_init(void) >> -{ >> -#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE) >> - >> -#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00) >> -#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28) >> - >> - /* UART4 clock enable */ >> - setbits_le32(RCC_MP_APB1ENSETR, BIT(16)); >> - >> -#define GPIOG_BASE 0x50008000 >> - /* GPIOG clock enable */ >> - writel(BIT(6), RCC_MP_AHB4ENSETR); >> - /* GPIO configuration for EVAL board >> - * => Uart4 TX = G11 >> - */ >> - writel(0xffbfffff, GPIOG_BASE + 0x00); >> - writel(0x00006000, GPIOG_BASE + 0x24); >> -#else >> - >> -#error("CONFIG_DEBUG_UART_BASE: not supported value") >> - >> -#endif >> -} >> -#endif > Reviewed-by: Patrice Chotard > > Thanks > > Patrice > _______________________________________________ > Uboot-stm32 mailing list > Uboot-stm32 at st-md-mailman.stormreply.com > https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32