From: Vignesh Raghavendra Date: Wed, 26 Feb 2020 12:59:44 +0530 Subject: [PATCH] spi: cadence-qspi: Move ref clock calculation to probe In-Reply-To: <20200224071051.19331-1-p.yadav@ti.com> References: <20200224071051.19331-1-p.yadav@ti.com> Message-ID: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de +Simon who converted driver to use clk_get* APIs On 24/02/20 12:40 pm, Pratyush Yadav wrote: > "assigned-clock-parents" and "assigned-clock-rates" DT properties take > effect only after ofdata_to_platdata() when clk_set_defaults() is called > in device_probe(). Therefore clk get rate() would return a wrong value > in ofdata_to_platdata() when compared with probe. Hence it needs to be > moved to probe. > > Tested on u-boot-ti/next. > Acked-by: Vignesh Raghavendra Regards Vignesh > Signed-off-by: Pratyush Yadav > --- > drivers/spi/cadence_qspi.c | 33 +++++++++++++++++---------------- > 1 file changed, 17 insertions(+), 16 deletions(-) > > diff --git a/drivers/spi/cadence_qspi.c b/drivers/spi/cadence_qspi.c > index 83b114ffe7..994a5948f1 100644 > --- a/drivers/spi/cadence_qspi.c > +++ b/drivers/spi/cadence_qspi.c > @@ -166,11 +166,28 @@ static int cadence_spi_probe(struct udevice *bus) > { > struct cadence_spi_platdata *plat = bus->platdata; > struct cadence_spi_priv *priv = dev_get_priv(bus); > + struct clk clk; > int ret; > > priv->regbase = plat->regbase; > priv->ahbbase = plat->ahbbase; > > + if (plat->ref_clk_hz == 0) { > + ret = clk_get_by_index(bus, 0, &clk); > + if (ret) { > +#ifdef CONFIG_CQSPI_REF_CLK > + plat->ref_clk_hz = CONFIG_CQSPI_REF_CLK; > +#else > + return ret; > +#endif > + } else { > + plat->ref_clk_hz = clk_get_rate(&clk); > + clk_free(&clk); > + if (IS_ERR_VALUE(plat->ref_clk_hz)) > + return plat->ref_clk_hz; > + } > + } > + > ret = reset_get_bulk(bus, &priv->resets); > if (ret) > dev_warn(bus, "Can't get reset: %d\n", ret); > @@ -268,8 +285,6 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus) > { > struct cadence_spi_platdata *plat = bus->platdata; > ofnode subnode; > - struct clk clk; > - int ret; > > plat->regbase = (void *)devfdt_get_addr_index(bus, 0); > plat->ahbbase = (void *)devfdt_get_addr_size_index(bus, 1, > @@ -305,20 +320,6 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus) > plat->tchsh_ns = ofnode_read_u32_default(subnode, "cdns,tchsh-ns", 20); > plat->tslch_ns = ofnode_read_u32_default(subnode, "cdns,tslch-ns", 20); > > - ret = clk_get_by_index(bus, 0, &clk); > - if (ret) { > -#ifdef CONFIG_CQSPI_REF_CLK > - plat->ref_clk_hz = CONFIG_CQSPI_REF_CLK; > -#else > - return ret; > -#endif > - } else { > - plat->ref_clk_hz = clk_get_rate(&clk); > - clk_free(&clk); > - if (IS_ERR_VALUE(plat->ref_clk_hz)) > - return plat->ref_clk_hz; > - } > - > debug("%s: regbase=%p ahbbase=%p max-frequency=%d page-size=%d\n", > __func__, plat->regbase, plat->ahbbase, plat->max_hz, > plat->page_size); >