From: U.Mutlu Date: Sat, 6 Apr 2019 00:27:26 +0200 Subject: [U-Boot] [sunxi/sun7i] ARMv7 SVC mode: PSCI not loaded and only 1st CPU core gets activated Message-ID: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 8bit To: u-boot@lists.denx.de Hi, when building u-boot for ARMv7 with these settings for SVC mode (ie. "Secure Mode"), instead of HYPervisor mode: ARM architecture ---> ... [*] Enable support for booting in non-secure mode [*] Boot in secure mode by default [ ] Enable support for hardware virtualization [*] Enable PSCI support (2) Maximum supported CPUs for PSCI [ ] Use LPAE page table format ... then only the first CPU core gets activated. How to bring the other core(s) online? I tried this from https://www.kernel.org/doc/html/v5.0/core-api/cpu_hotplug.html : # echo 1 > /sys/devices/system/cpu/cpu1/online bash: /sys/devices/system/cpu/cpu1/online: Permission denied (actually there is no "online" entry under cpu1, but also not under cpu0. Attached is the tree under /sys/devices/system/cpu/ ) # # Automatically generated file; DO NOT EDIT. # U-Boot 2019.04-rc4 Configuration ... CONFIG_SYS_ARCH="arm" CONFIG_SYS_CPU="armv7" CONFIG_SYS_SOC="sunxi" CONFIG_SYS_BOARD="sunxi" CONFIG_SYS_CONFIG_NAME="sun7i" ... CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1" ... # uname -a Linux r1-3 5.0.5 #1 SMP Sat Mar 30 05:34:40 CET 2019 armv7l GNU/Linux kernel conf has CONFIG_HOTPLUG_CPU=y # dmesg | grep -i "smp\|psci\|started in" [ 0.000000] Linux version 5.0.5 (u-ps at c22-local) (gcc version 9.0.1 20190326 (experimental) [trunk revision 269955] (GCC)) #1 SMP Sat Mar 30 05:34:40 CET 2019 [ 0.004154] smp: Bringing up secondary CPUs ... [ 0.004753] smp: Brought up 1 node, 1 CPU [ 0.004766] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.004772] CPU: All CPU(s) started in SVC mode. (ie. this means that PSCI is not loaded b/c otherwise there would be some "psci" lines in the log) # lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 2 On-line CPU(s) list: 0 Off-line CPU(s) list: 1 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: ARMv7 Processor rev 4 (v7l) CPU max MHz: 960.0000 CPU min MHz: 144.0000 See also: --------- http://linux-sunxi.org/PSCI https://www.kernel.org/doc/Documentation/devicetree/bindings/arm/psci.txt According to this page https://falstaff.agner.ch/2016/07/03/u-bootlinux-and-hyp-mode-on-armv7/ it seems in older u-boot versions it did activate all CPUs in SVC mode: " Brought up 2 CPUs SMP: Total of 2 processors activated (96.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. " -------------- next part -------------- /sys/devices/system/cpu/ ├── cpu0 │   ├── cpu_capacity │   ├── cpufreq -> ../cpufreq/policy0 │   ├── hotplug │   │   ├── fail │   │   ├── state │   │   └── target │   ├── of_node -> ../../../../firmware/devicetree/base/cpus/cpu at 0 │   ├── power │   │   ├── autosuspend_delay_ms │   │   ├── control │   │   ├── pm_qos_resume_latency_us │   │   ├── runtime_active_time │   │   ├── runtime_status │   │   └── runtime_suspended_time │   ├── subsystem -> ../../../../bus/cpu │   ├── topology │   │   ├── core_id │   │   ├── core_siblings │   │   ├── core_siblings_list │   │   ├── physical_package_id │   │   ├── thread_siblings │   │   └── thread_siblings_list │   └── uevent ├── cpu1 │   ├── cpu_capacity │   ├── cpufreq -> ../cpufreq/policy0 │   ├── hotplug │   │   ├── fail │   │   ├── state │   │   └── target │   ├── of_node -> ../../../../firmware/devicetree/base/cpus/cpu at 1 │   ├── power │   │   ├── autosuspend_delay_ms │   │   ├── control │   │   ├── pm_qos_resume_latency_us │   │   ├── runtime_active_time │   │   ├── runtime_status │   │   └── runtime_suspended_time │   ├── subsystem -> ../../../../bus/cpu │   └── uevent ├── cpufreq │   ├── policy0 │   │   ├── affected_cpus │   │   ├── cpuinfo_cur_freq │   │   ├── cpuinfo_max_freq │   │   ├── cpuinfo_min_freq │   │   ├── cpuinfo_transition_latency │   │   ├── related_cpus │   │   ├── scaling_available_frequencies │   │   ├── scaling_available_governors │   │   ├── scaling_cur_freq │   │   ├── scaling_driver │   │   ├── scaling_governor │   │   ├── scaling_max_freq │   │   ├── scaling_min_freq │   │   ├── scaling_setspeed │   │   └── stats │   │   ├── reset │   │   ├── time_in_state │   │   ├── total_trans │   │   └── trans_table │   └── schedutil │   └── rate_limit_us ├── cpuidle │   ├── current_driver │   └── current_governor_ro ├── hotplug │   └── states ├── isolated ├── kernel_max ├── modalias ├── offline ├── online ├── possible ├── power │   ├── autosuspend_delay_ms │   ├── control │   ├── runtime_active_time │   ├── runtime_status │   └── runtime_suspended_time ├── present └── uevent 20 directories, 63 files