From: Takashi Iwai Subject: Re: More issues with hdsp and 1.0.7 and 1.0.8 drivers Date: Fri, 14 Jan 2005 20:48:56 +0100 Message-ID: References: <20050114193044.NHXT13012.gx4.fuse.net@64BitBadass> Mime-Version: 1.0 (generated by SEMI 1.14.5 - "Awara-Onsen") Content-Type: text/plain; charset=US-ASCII Return-path: In-Reply-To: <20050114193044.NHXT13012.gx4.fuse.net@64BitBadass> Sender: alsa-devel-admin@lists.sourceforge.net Errors-To: alsa-devel-admin@lists.sourceforge.net List-Unsubscribe: , List-Post: List-Help: List-Subscribe: , List-Archive: To: Ivica Ico Bukvic Cc: alsa-devel@lists.sourceforge.net List-Id: alsa-devel@alsa-project.org At Fri, 14 Jan 2005 14:32:10 -0500, Ivica Ico Bukvic wrote: > > > At Thu, 13 Jan 2005 22:16:56 -0500, > > Ivica Ico Bukvic wrote: > > > > > > 1.0.8 driver install completely from scratch using sources has the > > following > > > problem: > > > > > > 1) hdsp card gets detected and everything goes fine until the firmware > > needs > > > to be loaded. > > > 2) at that point if I run hdsploader I get the following undocumented > > error: > > > > You need no longer to call hdsploader. The hdsp driver uses hotplug > > firmware loader if available. So, installating firmware files to the > > proper directory would suffice. (Note that the directory is different > > from the path for hdsploader.) > > > > Did you install alsa-firmware 1.0.8, too? > > I tried to and made no difference. For more info please see my other > e-mails. If the hotplug is supposed to do that, it certainly fails on my > system as I have to either explicitly tell it to do it or if the snd-hdsp is > being probed for the first time, I added the hdsploader to the "install" > clause so that it is triggered with modprobing of the snd-hdsp module... Invoking hdsploader does nothing with the driver with hotplug-fw loader support. It's simply ignored. > Of course, this only works on the 1.0.7 driver as 1.0.8 fails with the > aforementioned error. Just to make things as clear as possible, when using > 1.0.8 driver if I do not do anything, the firmware never gets loaded and the > red HOST light never turns off on the multiface suggesting that nothing got > to the card. Did you get any kernel messages after loading snd-hdsp? Anyway, please check the following: - Whether your kernel supports CONFIG_FW_LOADER. See /proc/config.gz (if any) or /usr/src/linux/.config file. - If fw-loader is supported, the firmware files must be installed properly. Check /usr/lib/hotplug/firmware directory whether multiface*.bin files exist. - Remove install in /etc/modprobe.conf to be sure. If they are OK and the system still doesn't work, something wrong in the driver or in the hotplug. As a last resort, you can disable the fw-loader support in hdsp driver. Remove the check in alsa-driver/pci/rme9652/hdsp.c #if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,0) so that the following is enabled always. #define HDSP_USE_HWDEP_LOADER (don't forget to remove the corresponding #endif, too) Takashi ------------------------------------------------------- The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt