From: Takashi Iwai Subject: Re: model needed for Clevo P150HM (Realtek ALC892) Date: Mon, 27 Jun 2011 14:32:38 +0200 Message-ID: References: <4E036C8F.3080709@gmail.com> <4E047441.4010003@gmail.com> <4E05C1B1.50302@gmail.com> <4E05C704.4080806@gmail.com> <4E05CE02.1070801@gmail.com> <4E082166.5060902@gmail.com> Mime-Version: 1.0 (generated by SEMI 1.14.6 - "Maruoka") Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: Received: from mx2.suse.de (cantor2.suse.de [195.135.220.15]) by alsa0.perex.cz (Postfix) with ESMTP id 852D0244FF for ; Mon, 27 Jun 2011 14:32:40 +0200 (CEST) In-Reply-To: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: alsa-devel-bounces@alsa-project.org Errors-To: alsa-devel-bounces@alsa-project.org To: Julian Sikorski Cc: alsa-devel@alsa-project.org List-Id: alsa-devel@alsa-project.org At Mon, 27 Jun 2011 11:19:36 +0200, Takashi Iwai wrote: > > At Mon, 27 Jun 2011 08:21:26 +0200, > Julian Sikorski wrote: > > > > W dniu 27.06.2011 08:04, Takashi Iwai pisze: > > > At Sat, 25 Jun 2011 14:01:06 +0200, > > > Julian Sikorski wrote: > > >> > > >> W dniu 25.06.2011 13:31, Julian Sikorski pisze: > > >>> W dniu 25.06.2011 13:08, Julian Sikorski pisze: > > >>>> W dniu 25.06.2011 09:11, Takashi Iwai pisze: > > >>>>> At Fri, 24 Jun 2011 13:25:53 +0200, > > >>>>> Julian Sikorski wrote: > > >>>>>> > > >>>>>> On 24/06/2011 11:12, Takashi Iwai wrote: > > >>>>>>> At Fri, 24 Jun 2011 10:34:01 +0200, > > >>>>>>> Takashi Iwai wrote: > > >>>>>>>> > > >>>>>>>> At Thu, 23 Jun 2011 18:40:47 +0200, > > >>>>>>>> Julian Sikorski wrote: > > >>>>>>>>> > > >>>>>>>>> On 23/06/2011 14:41, Takashi Iwai wrote: > > >>>>>>>>>> At Thu, 23 Jun 2011 08:36:55 +0200, > > >>>>>>>>>> Julian Sikorski wrote: > > >>>>>>>>>>> > > >>>>>>>>>>> Hi, > > >>>>>>>>>>> > > >>>>>>>>>>> I am coming here from pulseaudio-general mailing list [1]. I recently > > >>>>>>>>>>> got myself a Clevo P150HM laptop. It has 2.1 speakers, a built-in > > >>>>>>>>>>> microphone and the following connectors: > > >>>>>>>>>>> - headphone out > > >>>>>>>>>>> - microphone in; can be switched to center/lfe out > > >>>>>>>>>>> - spdif out; can be switched to rear speaker out > > >>>>>>>>>>> - line in; can be switched to side speaker out > > >>>>>>>>>>> Alsa does not seem to reflect that the device is capable of 5.1 and 7.1 > > >>>>>>>>>>> sound, and there are two configs showing up in pavucontrol (analog > > >>>>>>>>>>> output and analog headphones) which seem to be the same. I have uploaded > > >>>>>>>>>>> the output of alsa-info.sh [2]. Please let me know if more information > > >>>>>>>>>>> is needed. > > >>>>>>>>>> > > >>>>>>>>>> The current parser doesn't allow the multi-io pins when the primary > > >>>>>>>>>> output is no line-out. The patch below should fix (change) the > > >>>>>>>>>> behavior. It'll count HP out, too. > > >>>>>>>>>> > > >>>>>>>>>> > > >>>>>>>>>> Takashi > > >>>>>>>>>> > > >>>>>>>>>> --- > > >>>>>>>>>> diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c > > >>>>>>>>>> index fe56b2b..b0cf726 100644 > > >>>>>>>>>> --- a/sound/pci/hda/patch_realtek.c > > >>>>>>>>>> +++ b/sound/pci/hda/patch_realtek.c > > >>>>>>>>>> @@ -18992,6 +18992,7 @@ static int alc662_auto_fill_dac_nids(struct hda_codec *codec, > > >>>>>>>>>> hda_nid_t dac; > > >>>>>>>>>> > > >>>>>>>>>> spec->multiout.dac_nids = spec->private_dac_nids; > > >>>>>>>>>> + spec->multiout.num_dacs = 0; > > >>>>>>>>>> for (i = 0; i< cfg->line_outs; i++) { > > >>>>>>>>>> dac = alc_auto_look_for_dac(codec, cfg->line_out_pins[i]); > > >>>>>>>>>> if (!dac) > > >>>>>>>>>> @@ -19326,8 +19327,20 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) > > >>>>>>>>>> unsigned int location, defcfg; > > >>>>>>>>>> int num_pins; > > >>>>>>>>>> > > >>>>>>>>>> + if (cfg->line_out_type == AUTO_PIN_SPEAKER_OUT&& cfg->hp_outs == 1) { > > >>>>>>>>>> + /* use HP as primary out */ > > >>>>>>>>>> + cfg->speaker_outs = cfg->line_outs; > > >>>>>>>>>> + memcpy(cfg->speaker_pins, cfg->line_out_pins, > > >>>>>>>>>> + sizeof(cfg->speaker_pins)); > > >>>>>>>>>> + cfg->line_outs = cfg->hp_outs; > > >>>>>>>>>> + memcpy(cfg->line_out_pins, cfg->hp_pins, sizeof(cfg->hp_pins)); > > >>>>>>>>>> + cfg->hp_outs = 0; > > >>>>>>>>>> + memset(cfg->hp_pins, 0, sizeof(cfg->hp_pins)); > > >>>>>>>>>> + cfg->line_out_type = AUTO_PIN_HP_OUT; > > >>>>>>>>>> + alc662_auto_fill_dac_nids(codec, cfg); > > >>>>>>>>>> + } > > >>>>>>>>>> if (cfg->line_outs != 1 || > > >>>>>>>>>> - cfg->line_out_type != AUTO_PIN_LINE_OUT) > > >>>>>>>>>> + cfg->line_out_type == AUTO_PIN_SPEAKER_OUT) > > >>>>>>>>>> return 0; > > >>>>>>>>>> > > >>>>>>>>>> defcfg = snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]); > > >>>>>>>>>> @@ -19348,6 +19361,8 @@ static int alc_auto_add_multi_channel_mode(struct hda_codec *codec) > > >>>>>>>>>> spec->multi_ios = num_pins; > > >>>>>>>>>> spec->ext_channel_count = 2; > > >>>>>>>>>> spec->multiout.num_dacs = num_pins + 1; > > >>>>>>>>>> + /* for avoiding multi HP mixers */ > > >>>>>>>>>> + cfg->line_out_type = AUTO_PIN_LINE_OUT; > > >>>>>>>>>> } > > >>>>>>>>>> return 0; > > >>>>>>>>>> } > > >>>>>>>>> Would you like me to test this patch? If so, what should I apply it to > > >>>>>>>>> and how should I proceed? > > >>>>>>>> > > >>>>>>>> Yes, the test would be appreciated, of course. > > >>>>>>>> Apply it to the latest 3.0-rc kernel and test. > > >>>>>>> > > >>>>>>> Also, the additional patch below will give "Headphone" mixer control > > >>>>>>> back while new "Surround", "Center" and "LFE" will appear. > > >>>>>>> > > >>>>>>> Note that you'll need to change "Channel Mode" mixer control to "6ch" > > >>>>>>> for using the surround outputs even with these patches. As default, > > >>>>>>> it's set as "2ch". > > >>>>>>> > > >>>>>>> > > >>>>>>> Takashi > > >>>>>>> > > >>>>>> I will definitely try to give this a shot, but the outcome might be > > >>>>>> dependent on the fact whether Fedora 15 will want to work with 3.0-rc > > >>>>>> kernel. > > >>>>> > > >>>>> You can build the kernel by yourself at any time... > > >>>>> > > >>>>>> How about 8-channel sound btw? Under Windows the device claims to be > > >>>>>> capable of it. > > >>>>> > > >>>>> Do you have 4 jacks? Otherwise it's nonsense. > > >>>>> > > >>>>> > > >>>>> Takashi > > >>>> OK, I was able to successfully apply the patch and build the kernel. I > > >>>> tested it using: > > >>>> $ pasuspender bash > > >>>> $ speaker-test -Dplug:surround51 -c6 > > >>>> Once I set sound to 6-channel using alsamixer -c0, I was able to hear > > >>>> the sound for all 6 channels. Setting it to 4 channels took away LFE and > > >>>> center. Pulseaudio outputs are still a little messy, but this is out of > > >>>> ALSA scope, I think. > > >>>> > > >>>> Julian > > >>> It seems I spoke a bit too soon. The superfluous controls are still a > > >>> problem. Speaker and Headphone controls seem to be overlapping (new > > >>> output on amixer -c0 attached). They both control the headphones when > > >>> they are plugged in and internal speakers when not. > > >>> > > >>> Julian > > >>> > > >> Sorry for this email bombardment, but I just booted back to stock F15 > > >> kernel (2.6.38.8-32.fc15.x86_64) and noticed that speaker and headphone > > >> controls actually do what they advertise. Still, it is impossible to > > >> make the sound go through the speakers when headphones are plugged in (I > > >> tried pavucontrol for this). > > > > > > The auto-mute feature can be controlled "Auto-Mute Mode" mixer enum. > > > Set to "Disabled" will turn off the auto-mute in the driver side. > > > However... > > > > You are right - when auto-mute is disabled sound goes via both speakers > > and headphones when they are plugged. I did not know the function of > > auto-mute. > > However, the "Speaker" and "Headphone" controls still do influence both > > outputs, and "Speaker" can only be muted - there is no volume control > > available. So, in my opinion, they should either be merged altogether, > > or switched back to the way they work in 2.6.38.8-32.fc15.x86_64, that > > is setting the volume of speakers and headphones independently. > > Give alsa-info.sh outputs on your machine with the latest status for > further analysis. I think this issue was fixed now in topic/hda branch in sound git tree: git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git Give it a try. You can pull the branch into the latest Linus git tree for merging into the latest 3.0-rc. Takashi