From: Takashi Iwai Subject: Re: [PATCH v5] ALSA: usb: Work around CM6631 sample rate change bug Date: Wed, 03 Apr 2013 11:47:38 +0200 Message-ID: References: <20130326211004.GD18838@pvv.ntnu.no> Mime-Version: 1.0 (generated by SEMI 1.14.6 - "Maruoka") Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: Received: from mx2.suse.de (cantor2.suse.de [195.135.220.15]) by alsa0.perex.cz (Postfix) with ESMTP id ACE4026535C for ; Wed, 3 Apr 2013 11:47:39 +0200 (CEST) In-Reply-To: <20130326211004.GD18838@pvv.ntnu.no> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: alsa-devel-bounces@alsa-project.org Sender: alsa-devel-bounces@alsa-project.org To: Torstein Hegge Cc: alsa-devel@alsa-project.org, clemens@ladisch.de, zonque@gmail.com List-Id: alsa-devel@alsa-project.org At Tue, 26 Mar 2013 22:10:05 +0100, Torstein Hegge wrote: > > The C-Media CM6631 USB receiver doesn't respond to changes in sample rate > while the interface is active. The same behavior is observed in other UAC2 > hardware like the VIA VT1731. > > Reset the interface after setting the sampling frequency on sample rate > changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is > used. Otherwise, the device will try to use the sample rate of the previous > stream, causing distorted sound on sample rate changes. > > The reset is performed for all UAC2 devices, as it should not affect a > standards compliant device, but it is only necessary for C-Media CM6631, > VIA VT1731 and possibly others. > > Failure to read sample rate from the device is not handled as an error in > set_sample_rate_v2(), as (permanent or intermittent) failure to read sample > rate isn't essential for a successful sample rate set. > > Signed-off-by: Torstein Hegge > --- > Changes since v4: > - Sample rate read failure is no longer fatal. > > Failure to read sample rate from the device is degraded from a fatal error to > a warning message. The Schiit Bifrost has shown intermittent sample rate read > failures, and this shouldn't be a reason to abort the initialization. > > - The reset is performed for all UAC2 devices. > > The number of devices affected by this issue seems to be larger than just the > C-Media based devices, issues with the VIA VT1731 has been reported by Davor > Herga to alsa-user [1]. > > The additional reset should not affect standards compliant devices and will > hopefully improve the compatibility with future devices tested with the OS X > UAC2 driver. > > This can cause problems for a theoretical device where sample rate read always > fails, causing the reset to be performed every time the sample rate is set, > *and* where repeated resets cause resume after pause to not resume properly, > like the issues seen with CM6631 in the first iteration of this patch. > > [1] http://thread.gmane.org/gmane.linux.alsa.user/37312 > > > Changes since v3: > - Use given target rate instead of the new rate read from device when checking > if a reset is needed. Some devices (at least Schiit Bifrost) doesn't report a > reliable sample rate back right after setting a new rate. This appears to > fix the issues with v3 of this patch with the Schiit, as reported by Chris > Hermansen in http://thread.gmane.org/gmane.linux.alsa.user/36935/focus=37284 What about the latest status of the patch? If both Clemens and Daniel are happy with it, I can apply it for the next 3.9-rc. Though, it would be nicer if two identical calls of snd_usb_ctl_msg can be put into a single function, such as, static int get_cur_sample_rate_v2(struct snd_usb_audio *chip, int iface, int altsetting, int clock) { struct usb_device *dev = chip->dev; unsigned char data[4]; int err; err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), UAC2_CS_CUR, USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN, UAC2_CS_CONTROL_SAM_FREQ << 8, snd_usb_ctrl_intf(chip) | (clock << 8), data, sizeof(data)); if (err < 0) { snd_printk(KERN_WARNING "%d:%d:%d: cannot get freq (v2)\n", dev->devnum, iface, altsetting); return 0; } return data[0] | (data[1] << 8) | (data[2] << 16) | (data[3] << 24); } thanks, Takashi > > > sound/usb/clock.c | 45 +++++++++++++++++++++++++++++++++++---------- > 1 file changed, 35 insertions(+), 10 deletions(-) > > diff --git a/sound/usb/clock.c b/sound/usb/clock.c > index 5e634a2..9e2703a 100644 > --- a/sound/usb/clock.c > +++ b/sound/usb/clock.c > @@ -253,7 +253,7 @@ static int set_sample_rate_v2(struct snd_usb_audio *chip, int iface, > { > struct usb_device *dev = chip->dev; > unsigned char data[4]; > - int err, crate; > + int err, cur_rate, prev_rate; > int clock = snd_usb_clock_find_source(chip, fmt->clock); > > if (clock < 0) > @@ -266,6 +266,19 @@ static int set_sample_rate_v2(struct snd_usb_audio *chip, int iface, > return -ENXIO; > } > > + err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), UAC2_CS_CUR, > + USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN, > + UAC2_CS_CONTROL_SAM_FREQ << 8, > + snd_usb_ctrl_intf(chip) | (clock << 8), > + data, sizeof(data)); > + if (err < 0) { > + snd_printk(KERN_WARNING "%d:%d:%d: cannot get freq (v2)\n", > + dev->devnum, iface, fmt->altsetting); > + prev_rate = 0; > + } else { > + prev_rate = data[0] | (data[1] << 8) | (data[2] << 16) | (data[3] << 24); > + } > + > data[0] = rate; > data[1] = rate >> 8; > data[2] = rate >> 16; > @@ -280,19 +293,31 @@ static int set_sample_rate_v2(struct snd_usb_audio *chip, int iface, > return err; > } > > - if ((err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), UAC2_CS_CUR, > - USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN, > - UAC2_CS_CONTROL_SAM_FREQ << 8, > - snd_usb_ctrl_intf(chip) | (clock << 8), > - data, sizeof(data))) < 0) { > + err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), UAC2_CS_CUR, > + USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN, > + UAC2_CS_CONTROL_SAM_FREQ << 8, > + snd_usb_ctrl_intf(chip) | (clock << 8), > + data, sizeof(data)); > + if (err < 0) { > snd_printk(KERN_WARNING "%d:%d:%d: cannot get freq (v2)\n", > dev->devnum, iface, fmt->altsetting); > - return err; > + cur_rate = 0; > + } else { > + cur_rate = data[0] | (data[1] << 8) | (data[2] << 16) | (data[3] << 24); > } > > - crate = data[0] | (data[1] << 8) | (data[2] << 16) | (data[3] << 24); > - if (crate != rate) > - snd_printd(KERN_WARNING "current rate %d is different from the runtime rate %d\n", crate, rate); > + if (cur_rate != rate) { > + snd_printd(KERN_WARNING > + "current rate %d is different from the runtime rate %d\n", > + cur_rate, rate); > + } > + > + /* Some devices doesn't respond to sample rate changes while the > + * interface is active. */ > + if (rate != prev_rate) { > + usb_set_interface(dev, iface, 0); > + usb_set_interface(dev, iface, fmt->altsetting); > + } > > return 0; > } > -- > 1.7.10.4 > > _______________________________________________ > Alsa-devel mailing list > Alsa-devel@alsa-project.org > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel >