lvcreate_initrd & redhat 6.1
Got lvm running on at RH 6.1 after patching a 2.2.10 kernal. All looking very good. However, when I ran lvcreate_initrd, it errored out;
[root@l61 tools]# ./lvmcreate_initrd
Logical Volume Manager 0.7 by Heinz Mauelshagen 01/07/1999
lvmcreate_initrd -- this script creates a LVM initial ram disk in /boot/initrd.z
lvmcreate_initrd -- making ram filesystem lvmcreate_initrd -- ERROR making ram disk filesystem
Also, any suggestions as to where to put the "vgscan" and "vgchange -a y" on this system. It uses the "Sys V" rc.d setup (no /sbin/init.d/boot file).
Thanks,
Jon Polacheck
Quoted 6 lines
Got lvm running on at RH 6.1 after patching a 2.2.10 kernal. All looking very good. However, when I ran
lvcreate_initrd, it errored out;[root@l61 tools]# ./lvmcreate_initrd
Quoted 7 lines
Logical Volume Manager 0.7 by Heinz Mauelshagen 01/07/1999
lvmcreate_initrd-- this script creates a LVM initial ram disk in/boot/initrd.z
lvmcreate_initrd-- making ram filesystemlvmcreate_initrd-- ERROR making ram disk filesystem
Looks like you didn't configure your kernel to support ramdisks. If you do configure it, don't forget to add initial ramdisk support too.
Quoted 5 lines
Also, any suggestions as to where to put the "vgscan" and "vgchange -a y" on this system. It uses the "Sys V" rc.d setup (no
/sbin/init.d/bootfile).
I'm not used to RedHat but have a look at your /etc/inittab and figure out what is started at boottime by looking for entries with field 3 containing "boot" or "bootwait".
Put in vgscan and vgchange into the script started by these (after root has been mounted rw).
Another solution is (if you want to set up an initrd system with root contained in an LV anyway) to avoid vgscan and vgchange in the boot script by just copying the /dev/VolumeGroup/* special files from your initial ramdisk to your LV based root filesystem.
Heinz
--
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Systemmanagement CS-TS T-Nova
Entwicklungszentrum Darmstadt
Heinz Mauelshagen Otto-Roehm-Strasse 71c
Senior Systems Engineer Postfach 10 05 41
64205 Darmstadt [email protected] Germany +49 6151 886-425 FAX-386
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Hi,
the script lvcreate_initrd has a typo (-N 4096) in the line :
mke2fs -m0 -N 4096 $DEVRAM $INITRDSIZE >/dev/null 2>&1
Edit and change to -B 4096 :
mke2fs -m0 -B 4096 $DEVRAM $INITRDSIZE >/dev/null 2>&1
[]s
Fernando
----- Original Message -----
From: Jonathan S. Polacheck <[email protected]>
To: <[email protected]>
Sent: Monday, November 15, 1999 8:53 PM
Subject: [linux-lvm] lvcreate_initrd & redhat 6.1
Quoted 25 lines
Got lvm running on at RH 6.1 after patching a 2.2.10 kernal. All looking very good. However, when I ran
lvcreate_initrd, it errored out;[root@l61 tools]# ./lvmcreate_initrd
Logical Volume Manager 0.7 by Heinz Mauelshagen 01/07/1999
lvmcreate_initrd-- this script creates a LVM initial ram disk in/boot/initrd.z
lvmcreate_initrd-- making ram filesystemlvmcreate_initrd-- ERROR making ram disk filesystemAlso, any suggestions as to where to put the "vgscan" and "vgchange -a y" on this system. It uses the "Sys V" rc.d setup (no
/sbin/init.d/bootfile).Thanks,
Jon Polacheck
Quoted 2 lines · Jonathan S. Polacheck
lvmcreate_initrd-- making ram filesystemlvmcreate_initrd-- ERROR making ram disk filesystem
No (init) ramdisk support in your kernel.
Quoted 3 lines
Also, any suggestions as to where to put the "vgscan" and "vgchange -a y" on this system. It uses the "Sys V" rc.d setup (no
/sbin/init.d/bootfile).
Into /sbin on the initrd. The script does it for you nicely.
Signature · 3 lines
Reporter (to Mahatma Gandhi): Mr Gandhi, what do you think of Western Civilization? Gandhi: I think it would be a good idea.
Quoted 3 lines · Jonathan S. Polacheck
Also, any suggestions as to where to put the "vgscan" and "vgchange -a y" on this system. It uses the "Sys V" rc.d setup (no
/sbin/init.d/bootfile).
/etc/rc.d/rc.sysinit
Signature · 2 lines
Luca Berra -- [email protected] Communications Media & Services S.r.l.