AT91CAP9 support
Subsystems (6)
cover AT91CAP9 support
Hi,
This series of patches adds support for Atmel's AT91CAP9 Customizable Microcontrollers family:
http://www.atmel.com/products/AT91CAP/Default.asp
and more specifically for the AT91CAP9A-DK development kit:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4138
The supported features include:
- SDRAM
- Serial port DBGU
- LEDs
- SPI
- NOR Flash
- NAND Flash with ECC soft
- DataFlash (through SPI)
- Ethernet
This patch is to be applied on top of the current u-boot git tree + three small patches I submitted a few days ago but weren't picked up by anyone:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/35306 http://article.gmane.org/gmane.comp.boot-loaders.u-boot/35307 http://article.gmane.org/gmane.comp.boot-loaders.u-boot/35309
This is the fifth submission of the AT91CAP9 support, with some extra cleanup (one whitespace, a few #undefs and bd_info_ext removed).
Thanks.
Stelian.
PATCH 1/5 AT91CAP9 support : build integration
--- CREDITS | 4 ++++ MAKEALL | 1 + Makefile | 3 +++ drivers/mtd/dataflash.c | 4 ++-- net/eth.c | 4 ++++ 5 files changed, 14 insertions(+), 2 deletions(-)
CREDITS +4 -0
@@ -391,6 +391,10 @@ E: dan.poirot at windriver.com D: Support for the Wind River sbc405, sbc8240 board W: http://www.windriver.com +N: Stelian Pop +E: stelian.pop at leadtechdesign.com +D: Atmel AT91CAP9ADK support + N: Stefan Roese E: sr at denx.de D: AMCC PPC4xx Support
MAKEALL +1 -0
@@ -446,6 +446,7 @@ LIST_ARM7=" \ ######################################################################### LIST_ARM9=" \ + at91cap9adk \ at91rm9200dk \ cmc_pu2 \ ap920t \
Makefile +3 -0
@@ -2301,6 +2301,9 @@ xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$ xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1))) +at91cap9adk_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs at91cap9adk NULL at91cap9 + at91rm9200dk_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200dk NULL at91rm9200
drivers/mtd/dataflash.c +2 -2
@@ -36,7 +36,7 @@ struct dataflash_addr cs[CFG_MAX_DATAFLASH_BANKS] = { {CFG_DATAFLASH_LOGIC_ADDR_CS0, 0}, /* Logical adress, CS */ {CFG_DATAFLASH_LOGIC_ADDR_CS1, 1} }; -#elif defined(CONFIG_AT91SAM9263EK) +#elif defined(CONFIG_AT91SAM9263EK) || defined(CONFIG_AT91CAP9ADK) struct dataflash_addr cs[CFG_MAX_DATAFLASH_BANKS] = { {CFG_DATAFLASH_LOGIC_ADDR_CS0, 0}, /* Logical adress, CS */ };
@@ -48,7 +48,7 @@ struct dataflash_addr cs[CFG_MAX_DATAFLASH_BANKS] = {#endif /*define the area offsets*/ -#if defined(CONFIG_AT91SAM9261EK ) || defined(CONFIG_AT91SAM9260EK ) || defined(CONFIG_AT91SAM9263EK ) +#if defined(CONFIG_AT91SAM9261EK ) || defined(CONFIG_AT91SAM9260EK ) || defined(CONFIG_AT91SAM9263EK ) || defined(CONFIG_AT91CAP9ADK )#if defined(CONFIG_NEW_PARTITION )dataflash_protect_t area_list[NB_DATAFLASH_AREA ] = { {0x00000000, 0x00003FFF, FLAG_PROTECT_SET, 0, "Bootstrap"}, /* ROM code */
net/eth.c +4 -0
@@ -63,6 +63,7 @@ extern int atstk1000_eth_initialize(bd_t *);extern int atngw100_eth_initialize (bd_t *);extern int mcffec_initialize (bd_t *);extern int mcdmafec_initialize (bd_t *); +extern int at91cap9_eth_initialize (bd_t *);#ifdef CONFIG_API extern void (*push_packet)(volatile void *,int );
@@ -283,6 +284,9 @@ int eth_initialize(bd_t *bis)#if defined(CONFIG_FSLDMAFEC )mcdmafec_initialize (bis);#endif +#if defined(CONFIG_AT91CAP9 ) +at91cap9_eth_initialize (bis); +#endif if (!eth_devices) {puts ("No ethernet found.\n" );
Signature · 1 line
1.5.3.3
PATCH 2/5 AT91CAP9 support : include/ files
In reply to Stelian Pop--- include/asm-arm/arch-at91cap9/AT91CAP9.h | 518 ++++++++++++++++++++++++++++ include/asm-arm/arch-at91cap9/clk.h | 39 ++ include/asm-arm/arch-at91cap9/hardware.h | 38 ++ include/asm-arm/arch-at91cap9/memory-map.h | 34 ++ include/asm-arm/dma-mapping.h | 50 +++ 5 files changed, 679 insertions(+), 0 deletions(-) create mode 100644 include/asm-arm/arch-at91cap9/AT91CAP9.h create mode 100644 include/asm-arm/arch-at91cap9/clk.h create mode 100644 include/asm-arm/arch-at91cap9/hardware.h create mode 100644 include/asm-arm/arch-at91cap9/memory-map.h create mode 100644 include/asm-arm/dma-mapping.h
include/asm-arm/arch-at91cap9/AT91CAP9.h new file +518 -0
@@ -0,0 +1,518 @@ +/* +* (C) Copyright 2008 +* AT91CAP9 definitions +* Author : ATMEL AT91 application group +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef AT91CAP9_H +#define AT91CAP9_H + +typedef volatile unsigned int AT91_REG ; + +/* Static Memory Controller */ +typedef struct _AT91S_SMC { +AT91_REG SMC_SETUP0;/* Setup Register for CS 0 */ +AT91_REG SMC_PULSE0;/* Pulse Register for CS 0 */ +AT91_REG SMC_CYCLE0;/* Cycle Register for CS 0 */ +AT91_REG SMC_CTRL0;/* Control Register for CS 0 */ +AT91_REG SMC_SETUP1;/* Setup Register for CS 1 */ +AT91_REG SMC_PULSE1;/* Pulse Register for CS 1 */ +AT91_REG SMC_CYCLE1;/* Cycle Register for CS 1 */ +AT91_REG SMC_CTRL1;/* Control Register for CS 1 */ +AT91_REG SMC_SETUP2;/* Setup Register for CS 2 */ +AT91_REG SMC_PULSE2;/* Pulse Register for CS 2 */ +AT91_REG SMC_CYCLE2;/* Cycle Register for CS 2 */ +AT91_REG SMC_CTRL2;/* Control Register for CS 2 */ +AT91_REG SMC_SETUP3;/* Setup Register for CS 3 */ +AT91_REG SMC_PULSE3;/* Pulse Register for CS 3 */ +AT91_REG SMC_CYCLE3;/* Cycle Register for CS 3 */ +AT91_REG SMC_CTRL3;/* Control Register for CS 3 */ +AT91_REG SMC_SETUP4;/* Setup Register for CS 4 */ +AT91_REG SMC_PULSE4;/* Pulse Register for CS 4 */ +AT91_REG SMC_CYCLE4;/* Cycle Register for CS 4 */ +AT91_REG SMC_CTRL4;/* Control Register for CS 4 */ +AT91_REG SMC_SETUP5;/* Setup Register for CS 5 */ +AT91_REG SMC_PULSE5;/* Pulse Register for CS 5 */ +AT91_REG SMC_CYCLE5;/* Cycle Register for CS 5 */ +AT91_REG SMC_CTRL5;/* Control Register for CS 5 */ +AT91_REG SMC_SETUP6;/* Setup Register for CS 6 */ +AT91_REG SMC_PULSE6;/* Pulse Register for CS 6 */ +AT91_REG SMC_CYCLE6;/* Cycle Register for CS 6 */ +AT91_REG SMC_CTRL6;/* Control Register for CS 6 */ +AT91_REG SMC_SETUP7;/* Setup Register for CS 7 */ +AT91_REG SMC_PULSE7;/* Pulse Register for CS 7 */ +AT91_REG SMC_CYCLE7;/* Cycle Register for CS 7 */ +AT91_REG SMC_CTRL7;/* Control Register for CS 7 */ +}AT91S_SMC , *AT91PS_SMC ; + +/* SMC_SETUP : (SMC Offset: 0x0) Setup Register for CS x */ +#define AT91C_SMC_NWESETUP (0x3F << 0)/* NWE Setup Length */ +#define AT91C_SMC_NCSSETUPWR (0x3F << 8)/* NCS Setup Length for WRite */ +#define AT91C_SMC_NRDSETUP (0x3F << 16)/* NRD Setup Length */ +#define AT91C_SMC_NCSSETUPRD (0x3F << 24)/* NCS Setup Length for ReaD */ +/* SMC_PULSE : (SMC Offset: 0x4) Pulse Register for CS x */ +#define AT91C_SMC_NWEPULSE (0x7F << 0)/* NWE Pulse Length */ +#define AT91C_SMC_NCSPULSEWR (0x7F << 8)/* NCS Pulse Length for WRite */ +#define AT91C_SMC_NRDPULSE (0x7F << 16)/* NRD Pulse Length */ +#define AT91C_SMC_NCSPULSERD (0x7F << 24)/* NCS Pulse Length for ReaD */ +/* SMC_CYC : (SMC Offset: 0x8) Cycle Register for CS x */ +#define AT91C_SMC_NWECYCLE (0x1FF << 0)/* Total Write Cycle Length */ +#define AT91C_SMC_NRDCYCLE (0x1FF << 16)/* Total Read Cycle Length */ +/* SMC_CTRL : (SMC Offset: 0xc) Control Register for CS x */ +#define AT91C_SMC_READMODE (0x1 << 0)/* Read Mode */ +#define AT91C_SMC_WRITEMODE (0x1 << 1)/* Write Mode */ +#define AT91C_SMC_NWAITM (0x3 << 5)/* NWAIT Mode */ +/* External NWAIT disabled */ +#define AT91C_SMC_NWAITM_NWAIT_DISABLE (0x0 << 5) +/* External NWAIT enabled in frozen mode */ +#define AT91C_SMC_NWAITM_NWAIT_ENABLE_FROZEN (0x2 << 5) +/* External NWAIT enabled in ready mode */ +#define AT91C_SMC_NWAITM_NWAIT_ENABLE_READY (0x3 << 5) +#define AT91C_SMC_BAT (0x1 << 8)/* Byte Access Type */ +/* +* Write controled by ncs, nbs0, nbs1, nbs2, nbs3. +* Read controled by ncs, nrd, nbs0, nbs1, nbs2, nbs3. +*/ +#define AT91C_SMC_BAT_BYTE_SELECT (0x0 << 8) +/* +* Write controled by ncs, nwe0, nwe1, nwe2, nwe3. +* Read controled by ncs and nrd. +*/ +#define AT91C_SMC_BAT_BYTE_WRITE (0x1 << 8) +#define AT91C_SMC_DBW (0x3 << 12)/* Data Bus Width */ +#define AT91C_SMC_DBW_WIDTH_EIGTH_BITS (0x0 << 12) +#define AT91C_SMC_DBW_WIDTH_SIXTEEN_BITS (0x1 << 12) +#define AT91C_SMC_DBW_WIDTH_THIRTY_TWO_BITS (0x2 << 12) +#define AT91C_SMC_TDF (0xF << 16)/* Data Float Time */ +#define AT91C_SMC_TDFEN (0x1 << 20)/* TDF Enabled */ +#define AT91C_SMC_PMEN (0x1 << 24)/* Page Mode Enabled */ +#define AT91C_SMC_PS (0x3 << 28)/* Page Size */ +#define AT91C_SMC_PS_SIZE_FOUR_BYTES (0x0 << 28) +#define AT91C_SMC_PS_SIZE_EIGHT_BYTES (0x1 << 28) +#define AT91C_SMC_PS_SIZE_SIXTEEN_BYTES (0x2 << 28) +#define AT91C_SMC_PS_SIZE_THIRTY_TWO_BYTES (0x3 << 28) +/* SMC_SETUP : (SMC Offset: 0x10) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x14) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x18) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x1c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x20) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x24) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x28) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x2c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x30) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x34) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x38) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x3c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x40) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x44) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x48) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x4c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x50) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x54) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x58) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x5c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x60) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x64) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x68) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x6c) Control Register for CS x */ +/* SMC_SETUP : (SMC Offset: 0x70) Setup Register for CS x */ +/* SMC_PULSE : (SMC Offset: 0x74) Pulse Register for CS x */ +/* SMC_CYC : (SMC Offset: 0x78) Cycle Register for CS x */ +/* SMC_CTRL : (SMC Offset: 0x7c) Control Register for CS x */ + +/* AHB CCFG */ +typedef struct _AT91S_CCFG { +AT91_REG Reserved0[1 ]; +AT91_REG CCFG_MPBS0;/* MPB Slave 0 */ +AT91_REG CCFG_UDPHS;/* AHB Periphs */ +AT91_REG CCFG_MPBS1;/* MPB Slave 1 */ +AT91_REG CCFG_EBICSA;/* EBI Chip Select Assignement */ +AT91_REG Reserved1[2 ]; +AT91_REG CCFG_MPBS2;/* MPB Slave 2 */ +AT91_REG CCFG_MPBS3;/* MPB Slave 3 */ +AT91_REG CCFG_BRIDGE;/* APB Bridge */ +AT91_REG Reserved2[49 ]; +AT91_REG CCFG_MATRIXVERSION;/* Version */ +}AT91S_CCFG , *AT91PS_CCFG ; + +/* CCFG_UDPHS : (CCFG Offset: 0x8) UDPHS Configuration */ +#define AT91C_CCFG_UDPHS_UDP_SELECT (0x1 << 31)/* UDPHS or UDP */ +#define AT91C_CCFG_UDPHS_UDP_SELECT_UDPHS (0x0 << 31) +#define AT91C_CCFG_UDPHS_UDP_SELECT_UDP (0x1 << 31) +/* CCFG_EBICSA : (CCFG Offset: 0x10) EBI Chip Select Assignement Register */ +#define AT91C_EBI_CS1A (0x1 << 1)/* CS1 Assignment */ +#define AT91C_EBI_CS1A_SMC (0x0 << 1) +#define AT91C_EBI_CS1A_BCRAMC (0x1 << 1) +#define AT91C_EBI_CS3A (0x1 << 3)/* CS 3 Assignment */ +#define AT91C_EBI_CS3A_SMC (0x0 << 3) +#define AT91C_EBI_CS3A_SM (0x1 << 3) +#define AT91C_EBI_CS4A (0x1 << 4)/* CS4 Assignment */ +#define AT91C_EBI_CS4A_SMC (0x0 << 4) +#define AT91C_EBI_CS4A_CF (0x1 << 4) +#define AT91C_EBI_CS5A (0x1 << 5)/* CS 5 Assignment */ +#define AT91C_EBI_CS5A_SMC (0x0 << 5) +#define AT91C_EBI_CS5A_CF (0x1 << 5) +#define AT91C_EBI_DBPUC (0x1 << 8)/* Data Bus Pull-up */ +#define AT91C_EBI_DDRPUC (0x1 << 9)/* DDDR DQS Pull-up */ +#define AT91C_EBI_SUP (0x1 << 16)/* EBI Supply */ +#define AT91C_EBI_SUP_1V8 (0x0 << 16) +#define AT91C_EBI_SUP_3V3 (0x1 << 16) +#define AT91C_EBI_LP (0x1 << 17)/* EBI Low Power */ +#define AT91C_EBI_LP_LOW_DRIVE (0x0 << 17) +#define AT91C_EBI_LP_STD_DRIVE (0x1 << 17) +#define AT91C_CCFG_DDR_SDR_SELECT (0x1 << 31)/* DDR or SDR */ +#define AT91C_CCFG_DDR_SDR_SELECT_DDR (0x0 << 31) +#define AT91C_CCFG_DDR_SDR_SELECT_SDR (0x1 << 31) +/* CCFG_BRIDGE : (CCFG Offset: 0x24) BRIDGE Configuration */ +#define AT91C_CCFG_AES_TDES_SELECT (0x1 << 31)/* AES or TDES */ +#define AT91C_CCFG_AES_TDES_SELECT_AES (0x0 << 31) +#define AT91C_CCFG_AES_TDES_SELECT_TDES (0x1 << 31) + +/* PIO controller */ +typedef struct _AT91S_PIO { +AT91_REG PIO_PER;/* PIO Enable Register */ +AT91_REG PIO_PDR;/* PIO Disable Register */ +AT91_REG PIO_PSR;/* PIO Status Register */ +AT91_REG Reserved0[1 ]; +AT91_REG PIO_OER;/* Output Enable Register */ +AT91_REG PIO_ODR;/* Output Disable Register */ +AT91_REG PIO_OSR;/* Output Status Register */ +AT91_REG Reserved1[1 ]; +AT91_REG PIO_IFER;/* Input Filter Enable Register */ +AT91_REG PIO_IFDR;/* Input Filter Disable Register */ +AT91_REG PIO_IFSR;/* Input Filter Status Register */ +AT91_REG Reserved2[1 ]; +AT91_REG PIO_SODR;/* Set Output Data Register */ +AT91_REG PIO_CODR;/* Clear Output Data Register */ +AT91_REG PIO_ODSR;/* Output Data Status Register */ +AT91_REG PIO_PDSR;/* Pin Data Status Register */ +AT91_REG PIO_IER;/* Interrupt Enable Register */ +AT91_REG PIO_IDR;/* Interrupt Disable Register */ +AT91_REG PIO_IMR;/* Interrupt Mask Register */ +AT91_REG PIO_ISR;/* Interrupt Status Register */ +AT91_REG PIO_MDER;/* Multi-driver Enable Register */ +AT91_REG PIO_MDDR;/* Multi-driver Disable Register */ +AT91_REG PIO_MDSR;/* Multi-driver Status Register */ +AT91_REG Reserved3[1 ]; +AT91_REG PIO_PPUDR;/* Pull-up Disable Register */ +AT91_REG PIO_PPUER;/* Pull-up Enable Register */ +AT91_REG PIO_PPUSR;/* Pull-up Status Register */ +AT91_REG Reserved4[1 ]; +AT91_REG PIO_ASR;/* Select A Register */ +AT91_REG PIO_BSR;/* Select B Register */ +AT91_REG PIO_ABSR;/* AB Select Status Register */ +AT91_REG Reserved5[9 ]; +AT91_REG PIO_OWER;/* Output Write Enable Register */ +AT91_REG PIO_OWDR;/* Output Write Disable Register */ +AT91_REG PIO_OWSR;/* Output Write Status Register */ +}AT91S_PIO , *AT91PS_PIO ; + +/* Power Management Controller */ +typedef struct _AT91S_PMC { +AT91_REG PMC_SCER;/* System Clock Enable Register */ +AT91_REG PMC_SCDR;/* System Clock Disable Register */ +AT91_REG PMC_SCSR;/* System Clock Status Register */ +AT91_REG Reserved0[1 ]; +AT91_REG PMC_PCER;/* Peripheral Clock Enable Register */ +AT91_REG PMC_PCDR;/* Peripheral Clock Disable Register */ +AT91_REG PMC_PCSR;/* Peripheral Clock Status Register */ +AT91_REG PMC_UCKR;/* UTMI Clock Configuration Register */ +AT91_REG PMC_MOR;/* Main Oscillator Register */ +AT91_REG PMC_MCFR;/* Main Clock Frequency Register */ +AT91_REG PMC_PLLAR;/* PLL A Register */ +AT91_REG PMC_PLLBR;/* PLL B Register */ +AT91_REG PMC_MCKR;/* Master Clock Register */ +AT91_REG Reserved1[3 ]; +AT91_REG PMC_PCKR[8 ];/* Programmable Clock Register */ +AT91_REG PMC_IER;/* Interrupt Enable Register */ +AT91_REG PMC_IDR;/* Interrupt Disable Register */ +AT91_REG PMC_SR;/* Status Register */ +AT91_REG PMC_IMR;/* Interrupt Mask Register */ +}AT91S_PMC , *AT91PS_PMC ; + +/* PMC_SCER : (PMC Offset: 0x0) System Clock Enable Register */ +#define AT91C_PMC_PCK (0x1 << 0)/* Processor Clock */ +#define AT91C_PMC_OTG (0x1 << 5)/* USB OTG Clock */ +#define AT91C_PMC_UHP (0x1 << 6)/* USB Host Port Clock */ +#define AT91C_PMC_UDP (0x1 << 7)/* USB Device Port Clock */ +#define AT91C_PMC_PCK0 (0x1 << 8)/* Programmable Clock Output */ +#define AT91C_PMC_PCK1 (0x1 << 9)/* Programmable Clock Output */ +#define AT91C_PMC_PCK2 (0x1 << 10)/* Programmable Clock Output */ +#define AT91C_PMC_PCK3 (0x1 << 11)/* Programmable Clock Output */ +/* PMC_SCDR : (PMC Offset: 0x4) System Clock Disable Register */ +/* PMC_SCSR : (PMC Offset: 0x8) System Clock Status Register */ +/* CKGR_UCKR : (PMC Offset: 0x1c) UTMI Clock Configuration Register */ +/* CKGR_MOR : (PMC Offset: 0x20) Main Oscillator Register */ +/* CKGR_MCFR : (PMC Offset: 0x24) Main Clock Frequency Register */ +/* CKGR_PLLAR : (PMC Offset: 0x28) PLL A Register */ +/* CKGR_PLLBR : (PMC Offset: 0x2c) PLL B Register */ +/* PMC_MCKR : (PMC Offset: 0x30) Master Clock Register */ +#define AT91C_PMC_CSS (0x3 << 0)/* Clock Selection */ +#define AT91C_PMC_CSS_SLOW_CLK (0x0 << 0)/* Slow Clk */ +#define AT91C_PMC_CSS_MAIN_CLK (0x1 << 0)/* Main Clk */ +#define AT91C_PMC_CSS_PLLA_CLK (0x2 << 0)/* PLL A Clk */ +#define AT91C_PMC_CSS_PLLB_CLK (0x3 << 0)/* PLL B Clk */ +#define AT91C_PMC_PRES (0x7 << 2)/* Clock Prescaler */ +#define AT91C_PMC_PRES_CLK (0x0 << 2) +#define AT91C_PMC_PRES_CLK_2 (0x1 << 2) +#define AT91C_PMC_PRES_CLK_4 (0x2 << 2) +#define AT91C_PMC_PRES_CLK_8 (0x3 << 2) +#define AT91C_PMC_PRES_CLK_16 (0x4 << 2) +#define AT91C_PMC_PRES_CLK_32 (0x5 << 2) +#define AT91C_PMC_PRES_CLK_64 (0x6 << 2) +#define AT91C_PMC_MDIV (0x3 << 8)/* Master Clock Division */ +#define AT91C_PMC_MDIV_1 (0x0 << 8) +#define AT91C_PMC_MDIV_2 (0x1 << 8) +#define AT91C_PMC_MDIV_4 (0x2 << 8) +/* PMC_PCKR : (PMC Offset: 0x40) Programmable Clock Register */ +/* PMC_IER : (PMC Offset: 0x60) PMC Interrupt Enable Register */ +#define AT91C_PMC_MOSCS (0x1 << 0)/* MOSC mask */ +#define AT91C_PMC_LOCKA (0x1 << 1)/* PLL A mask */ +#define AT91C_PMC_LOCKB (0x1 << 2)/* PLL B mask */ +#define AT91C_PMC_MCKRDY (0x1 << 3)/* Master mask */ +#define AT91C_PMC_LOCKU (0x1 << 6)/* PLL UTMI mask */ +#define AT91C_PMC_PCK0RDY (0x1 << 8)/* PCK0_RDY mask */ +#define AT91C_PMC_PCK1RDY (0x1 << 9)/* PCK1_RDY mask */ +#define AT91C_PMC_PCK2RDY (0x1 << 10)/* PCK2_RDY mask */ +#define AT91C_PMC_PCK3RDY (0x1 << 11)/* PCK3_RDY mask */ +/* PMC_IDR : (PMC Offset: 0x64) PMC Interrupt Disable Register */ +/* PMC_SR : (PMC Offset: 0x68) PMC Status Register */ +/* PMC_IMR : (PMC Offset: 0x6c) PMC Interrupt Mask Register */ + +/* Reset controller */ +typedef struct _AT91S_RSTC { +AT91_REG RSTC_RCR;/* Reset Control Register */ +AT91_REG RSTC_RSR;/* Reset Status Register */ +AT91_REG RSTC_RMR;/* Reset Mode Register */ +}AT91S_RSTC , *AT91PS_RSTC ; + +/* RSTC_RCR : (RSTC Offset: 0x0) Reset Control Register */ +#define AT91C_RSTC_PROCRST (0x1 << 0)/* Processor Reset */ +#define AT91C_RSTC_ICERST (0x1 << 1)/* ICE Interface Reset */ +#define AT91C_RSTC_PERRST (0x1 << 2)/* Peripheral Reset */ +#define AT91C_RSTC_EXTRST (0x1 << 3)/* External Reset */ +#define AT91C_RSTC_KEY (0xFF << 24)/* Password */ +/* RSTC_RSR : (RSTC Offset: 0x4) Reset Status Register */ +#define AT91C_RSTC_URSTS (0x1 << 0)/* User Reset Status */ +#define AT91C_RSTC_RSTTYP (0x7 << 8)/* Reset Type */ +#define AT91C_RSTC_RSTTYP_GENERAL (0x0 << 8) +#define AT91C_RSTC_RSTTYP_WAKEUP (0x1 << 8) +#define AT91C_RSTC_RSTTYP_WATCHDOG (0x2 << 8) +#define AT91C_RSTC_RSTTYP_SOFTWARE (0x3 << 8) +#define AT91C_RSTC_RSTTYP_USER (0x4 << 8) +#define AT91C_RSTC_NRSTL (0x1 << 16)/* NRST pin level */ +#define AT91C_RSTC_SRCMP (0x1 << 17)/* Software Rst in Progress. */ +/* RSTC_RMR : (RSTC Offset: 0x8) Reset Mode Register */ +#define AT91C_RSTC_URSTEN (0x1 << 0)/* User Reset Enable */ +#define AT91C_RSTC_URSTIEN (0x1 << 4)/* User Reset Int. Enable */ +#define AT91C_RSTC_ERSTL (0xF << 8)/* User Reset Enable */ + +/* Periodic Timer Controller */ +typedef struct _AT91S_PITC { +AT91_REG PITC_PIMR;/* Period Interval Mode Register */ +AT91_REG PITC_PISR;/* Period Interval Status Register */ +AT91_REG PITC_PIVR;/* Period Interval Value Register */ +AT91_REG PITC_PIIR;/* Period Interval Image Register */ +}AT91S_PITC , *AT91PS_PITC ; + +/* PITC_PIMR : (PITC Offset: 0x0) Periodic Interval Mode Register */ +#define AT91C_PITC_PIV (0xFFFFF << 0)/* Periodic Interval Value */ +#define AT91C_PITC_PITEN (0x1 << 24)/* PIT Enable */ +#define AT91C_PITC_PITIEN (0x1 << 25)/* PIT Interrupt Enable */ +/* PITC_PISR : (PITC Offset: 0x4) Periodic Interval Status Register */ +#define AT91C_PITC_PITS (0x1 << 0)/* PIT Status */ +/* PITC_PIVR : (PITC Offset: 0x8) Periodic Interval Value Register */ +#define AT91C_PITC_CPIV (0xFFFFF << 0)/* Current Value */ +#define AT91C_PITC_PICNT (0xFFF << 20)/* Periodic Interval Counter */ +/* PITC_PIIR : (PITC Offset: 0xc) Periodic Interval Image Register */ + +/* Serial Paraller Interface */ +typedef struct _AT91S_SPI { +AT91_REG SPI_CR;/* Control Register */ +AT91_REG SPI_MR;/* Mode Register */ +AT91_REG SPI_RDR;/* Receive Data Register */ +AT91_REG SPI_TDR;/* Transmit Data Register */ +AT91_REG SPI_SR;/* Status Register */ +AT91_REG SPI_IER;/* Interrupt Enable Register */ +AT91_REG SPI_IDR;/* Interrupt Disable Register */ +AT91_REG SPI_IMR;/* Interrupt Mask Register */ +AT91_REG Reserved0[4 ]; +AT91_REG SPI_CSR[4 ];/* Chip Select Register */ +AT91_REG Reserved1[48 ]; +AT91_REG SPI_RPR;/* Receive Pointer Register */ +AT91_REG SPI_RCR;/* Receive Counter Register */ +AT91_REG SPI_TPR;/* Transmit Pointer Register */ +AT91_REG SPI_TCR;/* Transmit Counter Register */ +AT91_REG SPI_RNPR;/* Receive Next Pointer Register */ +AT91_REG SPI_RNCR;/* Receive Next Counter Register */ +AT91_REG SPI_TNPR;/* Transmit Next Pointer Register */ +AT91_REG SPI_TNCR;/* Transmit Next Counter Register */ +AT91_REG SPI_PTCR;/* PDC Transfer Control Register */ +AT91_REG SPI_PTSR;/* PDC Transfer Status Register */ +}AT91S_SPI , *AT91PS_SPI ; + +/* SPI_CR : (SPI Offset: 0x0) SPI Control Register */ +#define AT91C_SPI_SPIEN (0x1 << 0)/* SPI Enable */ +#define AT91C_SPI_SPIDIS (0x1 << 1)/* SPI Disable */ +#define AT91C_SPI_SWRST (0x1 << 7)/* SPI Software reset */ +#define AT91C_SPI_LASTXFER (0x1 << 24)/* SPI Last Transfer */ +/* SPI_MR : (SPI Offset: 0x4) SPI Mode Register */ +#define AT91C_SPI_MSTR (0x1 << 0)/* Master/Slave Mode */ +#define AT91C_SPI_PS (0x1 << 1)/* Peripheral Select */ +#define AT91C_SPI_PS_FIXED (0x0 << 1) +#define AT91C_SPI_PS_VARIABLE (0x1 << 1) +#define AT91C_SPI_PCSDEC (0x1 << 2)/* Chip Select Decode */ +#define AT91C_SPI_FDIV (0x1 << 3)/* Clock Selection */ +#define AT91C_SPI_MODFDIS (0x1 << 4)/* Mode Fault Detection */ +#define AT91C_SPI_LLB (0x1 << 7)/* Clock Selection */ +#define AT91C_SPI_PCS (0xF << 16)/* Peripheral Chip Select */ +#define AT91C_SPI_DLYBCS (0xFF << 24)/* Delay Between Chip Selects */ +/* SPI_RDR : (SPI Offset: 0x8) Receive Data Register */ +#define AT91C_SPI_RD (0xFFFF << 0)/* Receive Data */ +#define AT91C_SPI_RPCS (0xF << 16)/* Peripheral CS Status */ +/* SPI_TDR : (SPI Offset: 0xc) Transmit Data Register */ +#define AT91C_SPI_TD (0xFFFF << 0)/* Transmit Data */ +#define AT91C_SPI_TPCS (0xF << 16)/* Peripheral CS Status */ +/* SPI_SR : (SPI Offset: 0x10) Status Register */ +#define AT91C_SPI_RDRF (0x1 << 0)/* Receive Data Register Full */ +#define AT91C_SPI_TDRE (0x1 << 1)/* Trans. Data Register Empty */ +#define AT91C_SPI_MODF (0x1 << 2)/* Mode Fault Error */ +#define AT91C_SPI_OVRES (0x1 << 3)/* Overrun Error Status */ +#define AT91C_SPI_ENDRX (0x1 << 4)/* End of Receiver Transfer */ +#define AT91C_SPI_ENDTX (0x1 << 5)/* End of Receiver Transfer */ +#define AT91C_SPI_RXBUFF (0x1 << 6)/* RXBUFF Interrupt */ +#define AT91C_SPI_TXBUFE (0x1 << 7)/* TXBUFE Interrupt */ +#define AT91C_SPI_NSSR (0x1 << 8)/* NSSR Interrupt */ +#define AT91C_SPI_TXEMPTY (0x1 << 9)/* TXEMPTY Interrupt */ +#define AT91C_SPI_SPIENS (0x1 << 16)/* Enable Status */ +/* SPI_IER : (SPI Offset: 0x14) Interrupt Enable Register */ +/* SPI_IDR : (SPI Offset: 0x18) Interrupt Disable Register */ +/* SPI_IMR : (SPI Offset: 0x1c) Interrupt Mask Register */ +/* SPI_CSR : (SPI Offset: 0x30) Chip Select Register */ +#define AT91C_SPI_CPOL (0x1 << 0)/* Clock Polarity */ +#define AT91C_SPI_NCPHA (0x1 << 1)/* Clock Phase */ +#define AT91C_SPI_CSAAT (0x1 << 3)/* CS Active After Transfer */ +#define AT91C_SPI_BITS (0xF << 4)/* Bits Per Transfer */ +#define AT91C_SPI_BITS_8 (0x0 << 4)/* 8 Bits */ +#define AT91C_SPI_BITS_9 (0x1 << 4)/* 9 Bits */ +#define AT91C_SPI_BITS_10 (0x2 << 4)/* 10 Bits */ +#define AT91C_SPI_BITS_11 (0x3 << 4)/* 11 Bits */ +#define AT91C_SPI_BITS_12 (0x4 << 4)/* 12 Bits */ +#define AT91C_SPI_BITS_13 (0x5 << 4)/* 13 Bits */ +#define AT91C_SPI_BITS_14 (0x6 << 4)/* 14 Bits */ +#define AT91C_SPI_BITS_15 (0x7 << 4)/* 15 Bits */ +#define AT91C_SPI_BITS_16 (0x8 << 4)/* 16 Bits */ +#define AT91C_SPI_SCBR (0xFF << 8)/* Serial Clock Baud Rate */ +#define AT91C_SPI_DLYBS (0xFF << 16)/* Delay Before SPCK */ +#define AT91C_SPI_DLYBCT (0xFF << 24)/* Delay Between Transfers */ +/* SPI_PTCR : PDC Transfer Control Register */ +#define AT91C_PDC_RXTEN (0x1 << 0)/* Receiver Transfer Enable */ +#define AT91C_PDC_RXTDIS (0x1 << 1)/* Receiver Transfer Disable */ +#define AT91C_PDC_TXTEN (0x1 << 8)/* Transm. Transfer Enable */ +#define AT91C_PDC_TXTDIS (0x1 << 9)/* Transm. Transfer Disable */ + +/* PIO definitions */ +#define AT91C_PIO_PA0 (1 << 0)/* Pin Controlled by PA0 */ +#define AT91C_PA0_SPI0_MISO AT91C_PIO_PA0 +#define AT91C_PIO_PA1 (1 << 1)/* Pin Controlled by PA1 */ +#define AT91C_PA1_SPI0_MOSI AT91C_PIO_PA1 +#define AT91C_PIO_PA2 (1 << 2)/* Pin Controlled by PA2 */ +#define AT91C_PA2_SPI0_SPCK AT91C_PIO_PA2 +#define AT91C_PIO_PA3 (1 << 3)/* Pin Controlled by PA3 */ +#define AT91C_PA3_SPI0_NPCS1 AT91C_PIO_PA3 +#define AT91C_PIO_PA4 (1 << 4)/* Pin Controlled by PA4 */ +#define AT91C_PA4_SPI0_NPCS2A AT91C_PIO_PA4 +#define AT91C_PIO_PA5 (1 << 5)/* Pin Controlled by PA5 */ +#define AT91C_PA5_SPI0_NPCS0 AT91C_PIO_PA5 +#define AT91C_PIO_PA10 (1 << 10)/* Pin Controlled by PA10 */ +#define AT91C_PIO_PA11 (1 << 11)/* Pin Controlled by PA11 */ +#define AT91C_PIO_PA22 (1 << 22)/* Pin Controlled by PA22 */ +#define AT91C_PA22_TXD0 AT91C_PIO_PA22 +#define AT91C_PIO_PA23 (1 << 23)/* Pin Controlled by PA23 */ +#define AT91C_PA23_RXD0 AT91C_PIO_PA23 +#define AT91C_PIO_PA28 (1 << 28)/* Pin Controlled by PA28 */ +#define AT91C_PA28_SPI0_NPCS3A AT91C_PIO_PA28 +#define AT91C_PIO_PB21 (1 << 21)/* Pin Controlled by PB21 */ +#define AT91C_PB21_E_TXCK AT91C_PIO_PB21 +#define AT91C_PIO_PB22 (1 << 22)/* Pin Controlled by PB22 */ +#define AT91C_PB22_E_RXDV AT91C_PIO_PB22 +#define AT91C_PIO_PB23 (1 << 23)/* Pin Controlled by PB23 */ +#define AT91C_PB23_E_TX0 AT91C_PIO_PB23 +#define AT91C_PIO_PB24 (1 << 24)/* Pin Controlled by PB24 */ +#define AT91C_PB24_E_TX1 AT91C_PIO_PB24 +#define AT91C_PIO_PB25 (1 << 25)/* Pin Controlled by PB25 */ +#define AT91C_PB25_E_RX0 AT91C_PIO_PB25 +#define AT91C_PIO_PB26 (1 << 26)/* Pin Controlled by PB26 */ +#define AT91C_PB26_E_RX1 AT91C_PIO_PB26 +#define AT91C_PIO_PB27 (1 << 27)/* Pin Controlled by PB27 */ +#define AT91C_PB27_E_RXER AT91C_PIO_PB27 +#define AT91C_PIO_PB28 (1 << 28)/* Pin Controlled by PB28 */ +#define AT91C_PB28_E_TXEN AT91C_PIO_PB28 +#define AT91C_PIO_PB29 (1 << 29)/* Pin Controlled by PB29 */ +#define AT91C_PB29_E_MDC AT91C_PIO_PB29 +#define AT91C_PIO_PB30 (1 << 30)/* Pin Controlled by PB30 */ +#define AT91C_PB30_E_MDIO AT91C_PIO_PB30 +#define AT91C_PIO_PB31 (1 << 31)/* Pin Controlled by PB31 */ +#define AT91C_PIO_PC29 (1 << 29)/* Pin Controlled by PC29 */ +#define AT91C_PIO_PC30 (1 << 30)/* Pin Controlled by PC30 */ +#define AT91C_PC30_DRXD AT91C_PIO_PC30 +#define AT91C_PIO_PC31 (1 << 31)/* Pin Controlled by PC31 */ +#define AT91C_PC31_DTXD AT91C_PIO_PC31 +#define AT91C_PIO_PD0 (1 << 0)/* Pin Controlled by PD0 */ +#define AT91C_PD0_TXD1 AT91C_PIO_PD0 +#define AT91C_PD0_SPI0_NPCS2D AT91C_PIO_PD0 +#define AT91C_PIO_PD1 (1 << 1)/* Pin Controlled by PD1 */ +#define AT91C_PD1_RXD1 AT91C_PIO_PD1 +#define AT91C_PD1_SPI0_NPCS3D AT91C_PIO_PD1 +#define AT91C_PIO_PD2 (1 << 2)/* Pin Controlled by PD2 */ +#define AT91C_PD2_TXD2 AT91C_PIO_PD2 +#define AT91C_PIO_PD3 (1 << 3)/* Pin Controlled by PD3 */ +#define AT91C_PD3_RXD2 AT91C_PIO_PD3 +#define AT91C_PIO_PD15 (1 << 15)/* Pin Controlled by PD15 */ + +/* Peripheral ID */ +#define AT91C_ID_SYS 1/* System Controller */ +#define AT91C_ID_PIOABCD 2/* Parallel IO Controller A, B, C, D */ +#define AT91C_ID_US0 8/* USART 0 */ +#define AT91C_ID_US1 9/* USART 1 */ +#define AT91C_ID_US2 10/* USART 2 */ +#define AT91C_ID_SPI0 15/* Serial Peripheral Interface 0 */ +#define AT91C_ID_EMAC 22/* Ethernet Mac */ +#define AT91C_ID_UHP 29/* USB Host Port */ + +/* Base addresses */ +#define AT91C_BASE_SMC ((AT91PS_SMC) 0xFFFFE800)/* SMC */ +#define AT91C_BASE_CCFG ((AT91PS_CCFG) 0xFFFFEB10)/* CCFG */ +#define AT91C_BASE_DBGU ((unsigned long)0xFFFFEE00)/* DBGU */ +#define AT91C_BASE_PIOA ((AT91PS_PIO) 0xFFFFF200)/* PIOA */ +#define AT91C_BASE_PIOB ((AT91PS_PIO) 0xFFFFF400)/* PIOB */ +#define AT91C_BASE_PIOC ((AT91PS_PIO) 0xFFFFF600)/* PIOC */ +#define AT91C_BASE_PIOD ((AT91PS_PIO) 0xFFFFF800)/* PIOD */ +#define AT91C_BASE_PMC ((AT91PS_PMC) 0xFFFFFC00)/* PMC */ +#define AT91C_BASE_RSTC ((AT91PS_RSTC) 0xFFFFFD00)/* RSTC */ +#define AT91C_BASE_PITC ((AT91PS_PITC) 0xFFFFFD30)/* PITC */ +#define AT91C_BASE_US0 ((unsigned long)0xFFF8C000)/* US0 */ +#define AT91C_BASE_US1 ((unsigned long)0xFFF90000)/* US1 */ +#define AT91C_BASE_US2 ((unsigned long)0xFFF94000)/* US2 */ +#define AT91C_BASE_SPI0 ((AT91PS_SPI) 0xFFFA4000)/* SPI0 */ +#define AT91C_BASE_MACB ((unsigned long)0xFFFBC000)/* MACB */ + +#endif
include/asm-arm/arch-at91cap9/clk.h new file +39 -0
@@ -0,0 +1,39 @@ +/* +* (C) Copyright 2007 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#ifndef __ASM_ARM_ARCH_CLK_H__ +#define __ASM_ARM_ARCH_CLK_H__ + +#include <asm/arch/hardware.h> + +static inline unsigned long get_macb_pclk_rate (unsigned int dev_id) +{ +return AT91C_MASTER_CLOCK ; +} + +static inline unsigned long get_usart_clk_rate (unsigned int dev_id) +{ +return AT91C_MASTER_CLOCK ; +} + +#endif /* __ASM_ARM_ARCH_CLK_H__ */
include/asm-arm/arch-at91cap9/hardware.h new file +38 -0
@@ -0,0 +1,38 @@ +/* +* (C) Copyright 2007 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include <asm/sizes.h> + +#include <asm/arch/AT91CAP9.h> + +/* +* container_of - cast a member of a structure out to the containing structure +* +* @ptr: the pointer to the member. +* @type: the type of the container struct this is embedded in. +* @member: the name of the member within the struct. +*/ +#define container_of (ptr, type, member) ({ \ + const typeof(((type *)0)->member) *__mptr = (ptr); \ + (type *)((char *)__mptr - offsetof(type, member)); }) + +#endif
include/asm-arm/arch-at91cap9/memory-map.h new file +34 -0
@@ -0,0 +1,34 @@ +/* +* (C) Copyright 2007-2008 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#ifndef __ASM_ARM_ARCH_MEMORYMAP_H__ +#define __ASM_ARM_ARCH_MEMORYMAP_H__ + +#include <asm/arch/AT91CAP9.h> + +#define USART0_BASE AT91C_BASE_US0 +#define USART1_BASE AT91C_BASE_US1 +#define USART2_BASE AT91C_BASE_US2 +#define USART3_BASE AT91C_BASE_DBGU + +#endif /* __ASM_ARM_ARCH_MEMORYMAP_H__ */
include/asm-arm/dma-mapping.h new file +50 -0
50 lines not on this page · raw message
Signature · 1 line
1.5.3.3
PATCH 3/5 AT91CAP9 support : cpu/ files
In reply to Stelian Pop--- cpu/arm926ejs/at91cap9/Makefile | 46 ++++++++++ cpu/arm926ejs/at91cap9/config.mk | 2 + cpu/arm926ejs/at91cap9/ether.c | 35 ++++++++ cpu/arm926ejs/at91cap9/lowlevel_init.S | 43 +++++++++ cpu/arm926ejs/at91cap9/spi.c | 119 +++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/timer.c | 149 ++++++++++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/usb.c | 54 ++++++++++++ cpu/arm926ejs/interrupts.c | 2 +- cpu/arm926ejs/start.S | 3 + 9 files changed, 452 insertions(+), 1 deletions(-) create mode 100644 cpu/arm926ejs/at91cap9/Makefile create mode 100644 cpu/arm926ejs/at91cap9/config.mk create mode 100644 cpu/arm926ejs/at91cap9/ether.c create mode 100644 cpu/arm926ejs/at91cap9/lowlevel_init.S create mode 100644 cpu/arm926ejs/at91cap9/spi.c create mode 100644 cpu/arm926ejs/at91cap9/timer.c create mode 100644 cpu/arm926ejs/at91cap9/usb.c
cpu/arm926ejs/at91cap9/Makefile new file +46 -0
@@ -0,0 +1,46 @@ +# +# (C) Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(SOC).a + +COBJS = ether.o timer.o spi.o usb.o +SOBJS = lowlevel_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +all: $(obj).depend $(LIB) + +$(LIB): $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
cpu/arm926ejs/at91cap9/config.mk new file +2 -0
@@ -0,0 +1,2 @@ +PLATFORM_CPPFLAGS += -march=armv5te +PLATFORM_CPPFLAGS += $(call cc-option,-mtune=arm926ejs,)
cpu/arm926ejs/at91cap9/ether.c new file +35 -0
@@ -0,0 +1,35 @@ +/* +* (C) Copyright 2007-2008 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <asm/arch/AT91CAP9.h> + +extern int macb_eth_initialize (int id,void *regs,unsigned int phy_addr); + +#if defined(CONFIG_MACB ) && defined(CONFIG_CMD_NET ) +void at91cap9_eth_initialize (bd_t *bi) +{ +macb_eth_initialize (0 , (void *)AT91C_BASE_MACB ,0x00 ); +} +#endif
cpu/arm926ejs/at91cap9/lowlevel_init.S new file +43 -0
43 lines not on this page · raw message
cpu/arm926ejs/at91cap9/spi.c new file +119 -0
119 lines not on this page · raw message
cpu/arm926ejs/at91cap9/timer.c new file +149 -0
149 lines not on this page · raw message
cpu/arm926ejs/at91cap9/usb.c new file +54 -0
54 lines not on this page · raw message
cpu/arm926ejs/interrupts.c +1 -1
@@ -172,7 +172,7 @@ void do_irq (struct pt_regs *pt_regs)bad_mode (); } -#ifdef CONFIG_INTEGRATOR +#if defined(CONFIG_INTEGRATOR ) || defined(CONFIG_AT91CAP9ADK )/* Timer functionality supplied by Integrator board (AP or CP) */
cpu/arm926ejs/start.S +3 -0
@@ -182,6 +182,9 @@ clbss_l:str r2, [r0] /* clear loop... */ cmp r0, r1 ble clbss_l + bl coloured_LED_init + bl red_LED_on + ldr pc, _start_armboot _start_armboot:
Signature · 1 line
1.5.3.3
PATCH 3/5 AT91CAP9 support : cpu/ files
Quoted 11 lines
Signed-off-by Stelian Pop <[email protected]>---
cpu/arm926ejs/at91cap9/Makefile | 46 ++++++++++ cpu/arm926ejs/at91cap9/config.mk | 2 + cpu/arm926ejs/at91cap9/ether.c | 35 ++++++++ cpu/arm926ejs/at91cap9/lowlevel_init.S | 43 +++++++++ cpu/arm926ejs/at91cap9/spi.c | 119 +++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/timer.c | 149 ++++++++++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/usb.c | 54 ++++++++++++ cpu/arm926ejs/interrupts.c | 2 +- cpu/arm926ejs/start.S | 3 +
How much is different from the Atmel AT91SAM926x U-Boot patches on www.linux4sam.org? The CAP9 is very similar to the AT91SAM9263.
Should those chips share drivers?
Then it would be better to store the files in "cpu/arm926ejs/at91sam926x"
Best Regards
Ulf Samuelsson
PATCH 3/5 AT91CAP9 support : cpu/ files
Le vendredi 01 f?vrier 2008 ? 00:24 +0100, Ulf Samuelsson a ?crit :
Quoted 12 lines
Quoted 11 lines
Signed-off-by Stelian Pop <[email protected]>---
cpu/arm926ejs/at91cap9/Makefile | 46 ++++++++++ cpu/arm926ejs/at91cap9/config.mk | 2 + cpu/arm926ejs/at91cap9/ether.c | 35 ++++++++ cpu/arm926ejs/at91cap9/lowlevel_init.S | 43 +++++++++ cpu/arm926ejs/at91cap9/spi.c | 119 +++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/timer.c | 149 ++++++++++++++++++++++++++++++++ cpu/arm926ejs/at91cap9/usb.c | 54 ++++++++++++ cpu/arm926ejs/interrupts.c | 2 +- cpu/arm926ejs/start.S | 3 +
Quoted 1 line
How much is different from the Atmel AT91SAM926x U-Boot patches on www.linux4sam.org?
Quite different. The AT91SAM926x U-Boot patches are against u-boot-1.1.5 uses a lot of "local" drivers, whereas the AT91CAP9 port reuses the existing in-tree drivers where possible (for ethernet, NOR flash, etc)
Quoted 1 line
The CAP9 is very similar to the AT91SAM9263.
Yes, it is.
Quoted 1 line
Should those chips share drivers?
They do, but those drivers are also common to other cpus (the ethernet is also used by avr32). So the place for those drivers is under drivers/ more than in a common at91cap/sam cpu/ directory.
Quoted 1 line
Then it would be better to store the files in "cpu/arm926ejs/at91sam926x"
Maybe. Or maybe the whole cpu/ separation should be rethink (for example, if a port for the AT91CAP7 - which very similar to the AT91CAP9 except for the ARM7TDMI core - is to be done, where should it go ? Maybe the cpu and the soc elements should be separated.
Stelian.
Signature · 1 line
Stelian Pop <[email protected]>
PATCH 4/5 AT91CAP9 support : board/ files
In reply to Stelian Pop--- board/at91cap9adk/Makefile | 50 +++++++ board/at91cap9adk/at91cap9adk.c | 283 +++++++++++++++++++++++++++++++++++++++ board/at91cap9adk/config.mk | 1 + board/at91cap9adk/led.c | 80 +++++++++++ board/at91cap9adk/nand.c | 71 ++++++++++ board/at91cap9adk/u-boot.lds | 57 ++++++++ include/configs/at91cap9adk.h | 212 +++++++++++++++++++++++++++++ 7 files changed, 754 insertions(+), 0 deletions(-) create mode 100644 board/at91cap9adk/Makefile create mode 100644 board/at91cap9adk/at91cap9adk.c create mode 100644 board/at91cap9adk/config.mk create mode 100644 board/at91cap9adk/led.c create mode 100644 board/at91cap9adk/nand.c create mode 100644 board/at91cap9adk/u-boot.lds create mode 100644 include/configs/at91cap9adk.h
board/at91cap9adk/Makefile new file +50 -0
@@ -0,0 +1,50 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := at91cap9adk.o led.o nand.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/at91cap9adk/at91cap9adk.c new file +283 -0
283 lines not on this page · raw message
board/at91cap9adk/config.mk new file +1 -0
@@ -0,0 +1 @@ +TEXT_BASE = 0x73000000
board/at91cap9adk/led.c new file +80 -0
80 lines not on this page · raw message
board/at91cap9adk/nand.c new file +71 -0
71 lines not on this page · raw message
board/at91cap9adk/u-boot.lds new file +57 -0
57 lines not on this page · raw message
include/configs/at91cap9adk.h new file +212 -0
212 lines not on this page · raw message
Signature · 1 line
1.5.3.3
PATCH 4/5 AT91CAP9 support : board/ files
Quoted 8 lines
Signed-off-by Stelian Pop <[email protected]>---
board/at91cap9adk/Makefile | 50 +++++++ board/at91cap9adk/at91cap9adk.c | 283 +++++++++++++++++++++++++++++++++++++++ board/at91cap9adk/config.mk | 1 + board/at91cap9adk/led.c | 80 +++++++++++ board/at91cap9adk/nand.c | 71 ++++++++++ board/at91cap9adk/u-boot.lds | 57 ++++++++
I think it would be better if these files were located in the "board/atmel/at91cap9adk", instead of "board/at91cap9adk" Maybe Peter can fix that, it should not be too hard.
Best Regards
Ulf Samuelsson
PATCH 4/5 AT91CAP9 support : board/ files
Le jeudi 31 janvier 2008 ? 23:59 +0100, Ulf Samuelsson a ?crit :
Quoted 10 lines
Quoted 8 lines
Signed-off-by Stelian Pop <[email protected]>---
board/at91cap9adk/Makefile | 50 +++++++ board/at91cap9adk/at91cap9adk.c | 283 +++++++++++++++++++++++++++++++++++++++ board/at91cap9adk/config.mk | 1 + board/at91cap9adk/led.c | 80 +++++++++++ board/at91cap9adk/nand.c | 71 ++++++++++ board/at91cap9adk/u-boot.lds | 57 ++++++++
Quoted 2 lines
I think it would be better if these files were located in the "board/atmel/at91cap9adk", instead of "board/at91cap9adk"
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Stelian.
Signature · 1 line
Stelian Pop <[email protected]>
PATCH 4/5 AT91CAP9 support : board/ files
Quoted 11 lines · Stelian Pop
Le jeudi 31 janvier 2008 ? 23:59 +0100, Ulf Samuelsson a ?crit :
Quoted 10 lines
Quoted 9 lines
Signed-off-by Stelian Pop <[email protected]>---
board/at91cap9adk/Makefile | 50 +++++++board/at91cap9adk/at91cap9adk.c| 283 +++++++++++++++++++++++++++++++++++++++board/at91cap9adk/config.mk
| 1 +board/at91cap9adk/led.c | 80 +++++++++++ board/at91cap9adk/nand.c | 71 ++++++++++ board/at91cap9adk/u-boot.lds | 57 ++++++++
Quoted 5 lines
Quoted 2 lines
I think it would be better if these files were located in the "board/atmel/at91cap9adk", instead of "board/at91cap9adk"
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Right. I always prefer to "collect" board ports from one manufacturer/brand into a specific directory. This way the board directory doesn't get "polluted" that much. So it would be good if you could provide another patch to move all existing Atmel ports into the board/atmel directory which already exists.
Thanks.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 4/5 AT91CAP9 support : board/ files
Le samedi 02 f?vrier 2008 ? 06:59 +0100, Stefan Roese a ?crit :
Quoted 5 lines
Quoted 2 lines
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Right. I always prefer to "collect" board ports from one manufacturer/brand into a specific directory.
Manufacturer or brand/type ? Meaning, what do we do with the other AT91 based boards, which are not made by Atmel (cmc_pu2, csb637, kb9202, mp2usb) ?
Stelian.
Signature · 1 line
Stelian Pop <[email protected]>
PATCH 4/5 AT91CAP9 support : board/ files
Quoted 10 lines
Quoted 5 lines
Quoted 2 lines
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Right. I always prefer to "collect" board ports from one manufacturer/brand into a specific directory.
Manufacturer or brand/type ? Meaning, what do we do with the other AT91 based boards, which are not made by Atmel (
cmc_pu2, csb637, kb9202, mp2usb) ?
If they are not located in "board/atmel", it may make sense to create the "board/at91" and "board/avr32" directories for non-atmel boards.
Quoted 4 lines
Stelian.
Signature · 1 line
Stelian Pop <[email protected]>
Best Regards
Ulf Samuelsson
PATCH 4/5 AT91CAP9 support : board/ files
Quoted 3 lines · In message <[email protected]> you wrote:
If they are not located in "board/atmel", it may make sense to create the "board/at91" and "board/avr32" directories for non-atmel boards.
Please don't. Either we use board manufacturer subdirectories
consistently, or we just leave them untouched.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Drawing on my fine command of language, I said nothing.
PATCH 4/5 AT91CAP9 support : board/ files
In reply to Stelian PopQuoted 11 lines · On Sat, 02 Feb 2008 22:25:54 +0100 Stelian Pop <[email protected]> wrote:
Le samedi 02 f?vrier 2008 ? 06:59 +0100, Stefan Roese a ?crit :
Quoted 5 lines
Quoted 2 lines
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Right. I always prefer to "collect" board ports from one manufacturer/brand into a specific directory.
Manufacturer or brand/type ? Meaning, what do we do with the other AT91 based boards, which are not made by Atmel (
cmc_pu2, csb637, kb9202, mp2usb) ?
I think they should be collected according to board manufacturer or brand, not cpu type. So boards/atmel is for boards manufactured by Atmel, not all boards that happen to have an Atmel cpu on them.
Or at least that's what appears to be the current practice.
Haavard
PATCH 4/5 AT91CAP9 support : board/ files
Quoted 11 lines · Haavard Skinnemoen
Quoted 8 lines · On Sat, 02 Feb 2008 22:25:54 +0100 Stelian Pop <[email protected]> wrote:
Le samedi 02 f?vrier 2008 ? 06:59 +0100, Stefan Roese a ?crit :
Quoted 5 lines
Quoted 2 lines
I did think of that. I have no strong feeling about that. Except that if we put at91cap9adk under board/atmel, at91rm9200dk should go there too.
Right. I always prefer to "collect" board ports from one manufacturer/brand into a specific directory.
Quoted 7 lines
Quoted 3 lines
Manufacturer or brand/type ? Meaning, what do we do with the other AT91 based boards, which are not made by Atmel (
cmc_pu2, csb637, kb9202, mp2usb) ?I think they should be collected according to board manufacturer or brand, not cpu type. So boards/atmel is for boards manufactured by Atmel, not all boards that happen to have an Atmel cpu on them.
I agree too, they should be collected according to board manufacturer not cpu type.
Best Regards,
J.
PATCH 1/1 AT91CAP9 support : move board files to Atmel vendor directory.
In reply to Haavard SkinnemoenLe dimanche 03 f?vrier 2008 ? 13:54 +0100, Haavard Skinnemoen a ?crit :
Quoted 5 lines
I think they should be collected according to board manufacturer or brand, not cpu type. So boards/atmel is for boards manufactured by Atmel, not all boards that happen to have an Atmel cpu on them.
Or at least that's what appears to be the current practice.
Ok, so everybody seem to agree that it is good practice to use the vendor directories.
The (incremental) patch below moves the AT91CAP9ADK board files into the vendor directory.
Stelian.
---
AT91CAP9 support : move at91cap9adk board files to Atmel vendor directory.
---
Makefile | 2 +-
board/{ => atmel}/at91cap9adk/Makefile | 0
board/{ => atmel}/at91cap9adk/at91cap9adk.c | 0
board/{ => atmel}/at91cap9adk/config.mk | 0
board/{ => atmel}/at91cap9adk/led.c | 0
board/{ => atmel}/at91cap9adk/nand.c | 0
board/{ => atmel}/at91cap9adk/u-boot.lds | 0
7 files changed, 1 insertions(+), 1 deletions(-)
rename board/{ => atmel}/at91cap9adk/Makefile (100%)
rename board/{ => atmel}/at91cap9adk/at91cap9adk.c (100%)
rename board/{ => atmel}/at91cap9adk/config.mk (100%)
rename board/{ => atmel}/at91cap9adk/led.c (100%)
rename board/{ => atmel}/at91cap9adk/nand.c (100%)
rename board/{ => atmel}/at91cap9adk/u-boot.lds (100%)Makefile +1 -1
@@ -2302,7 +2302,7 @@ xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$ xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1))) at91cap9adk_config : unconfig - @$(MKCONFIG) $(@:_config=) arm arm926ejs at91cap9adk NULL at91cap9 + @$(MKCONFIG) $(@:_config=) arm arm926ejs at91cap9adk atmel at91cap9 at91rm9200dk_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200dk NULL at91rm9200
board/atmel/at91cap9adk/Makefile renamed from board/at91cap9adk/Makefile +0 -0
board/atmel/at91cap9adk/at91cap9adk.c renamed from board/at91cap9adk/at91cap9adk.c +0 -0
board/atmel/at91cap9adk/config.mk renamed from board/at91cap9adk/config.mk +0 -0
board/atmel/at91cap9adk/led.c renamed from board/at91cap9adk/led.c +0 -0
board/atmel/at91cap9adk/nand.c renamed from board/at91cap9adk/nand.c +0 -0
board/atmel/at91cap9adk/u-boot.lds renamed from board/at91cap9adk/u-boot.lds +0 -0
Signature · 5 lines
1.5.3.3 -- Stelian Pop <[email protected]>
PATCH 1/1 AT91CAP9 support : move board files to Atmel vendor directory.
Quoted 9 lines · Stelian Pop
Le dimanche 03 f?vrier 2008 ? 13:54 +0100, Haavard Skinnemoen a ?crit :
Quoted 5 lines
I think they should be collected according to board manufacturer or brand, not cpu type. So boards/atmel is for boards manufactured by Atmel, not all boards that happen to have an Atmel cpu on them.
Or at least that's what appears to be the current practice.
Ok, so everybody seem to agree that it is good practice to use the vendor directories.
Yep, thats what I meant.
Quoted 2 lines
The (incremental) patch below moves the AT91CAP9ADK board files into the vendor directory.
Thanks.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 1/1 AT91CAP9 support : move board files to Atmel vendordirectory.
In reply to Stelian PopThanks Stelian
Peter
Quoted 16 lines
-----Original Message-----
From: Stelian Pop [mailto:stelian at popies.net]
Sent: 04 February 2008 09:43
To: Haavard Skinnemoen
Cc: Stefan Roese; u-boot-users at lists.sourceforge.net; Peter Pearse
Subject: [PATCH ARM] AT91CAP9 support : move board files to Atmel vendordirectory.The (incremental) patch below moves the AT91CAP9ADK board files into the vendor directory.
Stelian.
---
Signature · 1 line
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
PATCH 1/1 Move AT91RM9200DK board support under board/atmel
In reply to Stelian PopWe already have a vendor subdir for Atmel, so we should use it.
---
Compile-tested and found exactly as broken as before since it tries to compile a freescale SPI driver for some reason...
Makefile | 2 +-
board/{ => atmel}/at91rm9200dk/Makefile | 0
board/{ => atmel}/at91rm9200dk/at91rm9200dk.c | 0
board/{ => atmel}/at91rm9200dk/config.mk | 0
board/{ => atmel}/at91rm9200dk/flash.c | 0
board/{ => atmel}/at91rm9200dk/led.c | 0
board/{ => atmel}/at91rm9200dk/mux.c | 0
board/{ => atmel}/at91rm9200dk/u-boot.lds | 0
8 files changed, 1 insertions(+), 1 deletions(-)
rename board/{ => atmel}/at91rm9200dk/Makefile (100%)
rename board/{ => atmel}/at91rm9200dk/at91rm9200dk.c (100%)
rename board/{ => atmel}/at91rm9200dk/config.mk (100%)
rename board/{ => atmel}/at91rm9200dk/flash.c (100%)
rename board/{ => atmel}/at91rm9200dk/led.c (100%)
rename board/{ => atmel}/at91rm9200dk/mux.c (100%)
rename board/{ => atmel}/at91rm9200dk/u-boot.lds (100%)Makefile +1 -1
@@ -2302,7 +2302,7 @@ xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$ xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1))) at91rm9200dk_config : unconfig - @$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200dk NULL at91rm9200 + @$(MKCONFIG) $(@:_config=) arm arm920t at91rm9200dk atmel at91rm9200 cmc_pu2_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm920t cmc_pu2 NULL at91rm9200
board/atmel/at91rm9200dk/Makefile renamed from board/at91rm9200dk/Makefile +0 -0
board/atmel/at91rm9200dk/at91rm9200dk.c renamed from board/at91rm9200dk/at91rm9200dk.c +0 -0
board/atmel/at91rm9200dk/config.mk renamed from board/at91rm9200dk/config.mk +0 -0
board/atmel/at91rm9200dk/flash.c renamed from board/at91rm9200dk/flash.c +0 -0
board/atmel/at91rm9200dk/led.c renamed from board/at91rm9200dk/led.c +0 -0
board/atmel/at91rm9200dk/mux.c renamed from board/at91rm9200dk/mux.c +0 -0
board/atmel/at91rm9200dk/u-boot.lds renamed from board/at91rm9200dk/u-boot.lds +0 -0
Signature · 1 line
1.5.3.6
PATCH 1/1 Move AT91RM9200DK board support under board/atmel
Quoted 2 lines · On Sat, 2 Feb 2008 12:40:50 +0100 Haavard Skinnemoen <[email protected]>…
Compile-tested and found exactly as broken as before since it tries to compile a freescale SPI driver for some reason...
After fixing that issue, the u-boot.bin files generated before and after this patch are identical apart from the git ID in the version string and the build date/time in the banner.
Haavard
PATCH 1/1 Move AT91RM9200DK board support under board/atmel
Quoted 10 lines
-----Original Message-----
From: Haavard Skinnemoen [mailto:hskinnemoen at atmel.com]
Sent: 02 February 2008 12:38
To: Haavard Skinnemoen
Cc: Peter Pearse; u-boot-users at lists.sourceforge.net
Subject: Re: [U-Boot-Users] [PATCH] Move AT91RM9200DK board support under board/atmel
Quoted 2 lines
On Sat, 2 Feb 2008 12:40:50 +0100
Haavard Skinnemoen <[email protected]> wrote:
Haarvard
Until the next merge your patch is available from git://linux-arm.org/u-boot-armdev#080802_at91rm9200dk.
Regards
Peter
PATCH 1/1 Move AT91RM9200DK board support under board/atmel
In reply to Haavard SkinnemoenQuoted 3 lines · Haavard Skinnemoen
We already have a vendor subdir for Atmel, so we should use it.
Signed-off-by Haavard Skinnemoen <[email protected]>
Nice, thanks.
Best regards,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
PATCH 5/5 AT91CAP9 support : MACB changes
In reply to Stelian Pop--- drivers/net/macb.c | 8 ++++++++ drivers/net/macb.h | 6 ++++++ 2 files changed, 14 insertions(+), 0 deletions(-)
drivers/net/macb.c +8 -0
@@ -417,10 +417,18 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)/* choose RMII or MII mode. This depends on the board */ #ifdef CONFIG_RMII +#ifdef CONFIG_AT91CAP9ADK +macb_writel (macb,USRIO ,MACB_BIT (RMII ) |MACB_BIT (CLKEN )); +#else macb_writel (macb,USRIO ,0 ); +#endif +#else +#ifdef CONFIG_AT91CAP9ADK +macb_writel (macb,USRIO ,MACB_BIT (CLKEN ));#else macb_writel (macb,USRIO ,MACB_BIT (MII ));#endif +#endif /* CONFIG_RMII */ if (!macb_phy_init (macb))return -1 ;
drivers/net/macb.h +6 -0
@@ -222,6 +222,12 @@#define MACB_TX_PAUSE_ZERO_OFFSET 3#define MACB_TX_PAUSE_ZERO_SIZE 1 +/* Bitfields in USRIO (AT91) */ +#define MACB_RMII_OFFSET 0 +#define MACB_RMII_SIZE 1 +#define MACB_CLKEN_OFFSET 1 +#define MACB_CLKEN_SIZE 1 +/* Bitfields in WOL */ #define MACB_IP_OFFSET 0#define MACB_IP_SIZE 16
Signature · 1 line
1.5.3.3