partition table: chs question
hi.
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
so, how should a partition table look like ?
regards, andreas
Quoted 2 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
http://www.linuxdoc.org/HOWTO/Large-Disk-HOWTO.html
--
Quoted 9 lines · Andreas Jellinghaus
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
so, how should a partition table look like ?
Since these values will never be used you can imagine that they are not of great interest. Do whatever you like.
Please also check vger.timpanogas.org/nwfs/nwfs.tar.gz:disk.c for NetWare specific calculations of the CHS values, a different method is used for NetWare partitions vs. everything else (Novell just had to be different). If you do not use their methods on NetWare partitions, NetWare will not recognize the partition entries correctly, and will attempt to reinitialize the entire partition table on a system if they are wrong (Ouch!). NetWare does a different calculation for conversion of cylinder values above 1024.
Jeff
----- Original Message -----
From: "Guest section DW" <[email protected]>
To: "Andreas Jellinghaus" <[email protected]>;
<[email protected]>
Sent: Sunday, February 25, 2001 2:47 PM
Subject: Re: partition table: chs question
Quoted 19 lines · Andreas Jellinghaus
Quoted 10 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
so, how should a partition table look like ?
Since these values will never be used you can imagine that they are not of great interest. Do whatever you like.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
It does not matter because the usage of CHS will dies soon because it was voted to death in Austin last week. There will only be LBA addressing from now on out.
Quoted 40 lines · Jeff V. Merkey
Please also check vger.timpanogas.org/nwfs/nwfs.tar.gz:disk.c for NetWare specific calculations of the CHS values, a different method is used for NetWare partitions vs. everything else (Novell just had to be different). If you do not use their methods on NetWare partitions, NetWare will not recognize the partition entries correctly, and will attempt to reinitialize the entire partition table on a system if they are wrong (Ouch!). NetWare does a different calculation for conversion of cylinder values above 1024.
Jeff
----- Original Message -----
From: "Guest section DW" <[email protected]>
To: "Andreas Jellinghaus" <[email protected]>;
<[email protected]>
Sent: Sunday, February 25, 2001 2:47 PM
Subject: Re: partition table: chs questionQuoted 12 lines · Andreas Jellinghaus
Quoted 10 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
so, how should a partition table look like ?
Quoted 7 lines
Since these values will never be used you can imagine that they are not of great interest. Do whatever you like.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 6 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Andre Hedrick
Linux ATA Development
ASL Kernel Development
-----------------------------------------------------------------------------
ASL, Inc. Toll free: 1-877-ASL-3535 1757 Houret Court Fax: 1-408-941-2071 Milpitas, CA 95035 Web: www.aslab.com
Quoted 5 lines · Andre Hedrick
It does not matter because the usage of CHS will dies soon because it was voted to death in Austin last week. There will only be LBA addressing from now on out.
If someone has Linux and NetWare dual booted on a system, and does not fill out the CHS fields properly for NetWare partitions, When NetWare boots, it will wipe the partition table (it will ask you first) and will not recognize any of the partitions. It does this because if it sees CHS values it does not expect, it assumes the partition table has been corrupted.
Jeff
Quoted 57 lines · Jeff V. Merkey
Quoted 41 lines
Please also check vger.timpanogas.org/nwfs/nwfs.tar.gz:disk.c for NetWare specific calculations of the CHS values, a different method is used for NetWare partitions vs. everything else (Novell just had to be different). If you do not use their methods on NetWare partitions, NetWare will not recognize the partition entries correctly, and will attempt to reinitialize the entire partition table on a system if they are wrong (Ouch!). NetWare does a different calculation for conversion of cylinder values above 1024.
Jeff
----- Original Message -----
From: "Guest section DW" <[email protected]>
To: "Andreas Jellinghaus" <[email protected]>;
<[email protected]>
Sent: Sunday, February 25, 2001 2:47 PM
Subject: Re: partition table: chs questionQuoted 12 lines · Andreas Jellinghaus
Quoted 10 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
so, how should a partition table look like ?
Quoted 7 lines
Since these values will never be used you can imagine that they are not of great interest. Do whatever you like.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/Quoted 6 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/Andre Hedrick
Linux ATA Development
ASL Kernel Development
-----------------------------------------------------------------------------ASL, Inc. Toll free: 1-877-ASL-3535 1757 Houret Court Fax: 1-408-941-2071 Milpitas, CA 95035 Web: www.aslab.com
Quoted 7 lines · Jeff V. Merkey
Quoted 5 lines · Andre Hedrick
It does not matter because the usage of CHS will dies soon because it was voted to death in Austin last week. There will only be LBA addressing from now on out.
Quoted 6 lines
If someone has Linux and NetWare dual booted on a system, and does not fill out the CHS fields properly for NetWare partitions, When NetWare boots, it will wipe the partition table (it will ask you first) and will not recognize any of the partitions. It does this because if it sees CHS values it does not expect, it assumes the partition table has been corrupted.
Then Netware is a bad HOST-Driver and people should expect to be hurt by using a HOST that is not compliant. It is the responsiblity of the user to tell the HOST-OS what it needs to do. Especially if one of the OSes can not be intelligent enough to adpat to the changes.
Regards,
Andre Hedrick
Linux ATA Development
ASL Kernel Development
-----------------------------------------------------------------------------
ASL, Inc. Toll free: 1-877-ASL-3535 1757 Houret Court Fax: 1-408-941-2071 Milpitas, CA 95035 Web: www.aslab.com
----- Original Message -----
From: "Andre Hedrick" <[email protected]>
To: "Jeff V. Merkey" <[email protected]>
Cc: "Jeff V. Merkey" <[email protected]>; "Guest section DW" <[email protected]>; "Andreas Jellinghaus" <[email protected]>; <[email protected]>
Sent: Monday, February 26, 2001 10:32 AM
Subject: Re: partition table: chs question
Quoted 6 lines · Jeff V. Merkey
Quoted 5 lines · Andre Hedrick
Quoted 3 lines
It does not matter because the usage of CHS will dies soon because it
was
Quoted 10 lines
Quoted 9 lines
Quoted 2 lines
voted to death in Austin last week. There will only be LBA addressing from now on out.
If someone has Linux and NetWare dual booted on a system, and does not fill out the CHS fields properly for NetWare partitions, When NetWare boots, it will wipe the partition table (it will ask you first) and will not recognize any of the partitions. It does this because if it sees CHS values it does not expect, it assumes the partition table has been corrupted.
Quoted 4 lines
Then Netware is a bad HOST-Driver and people should expect to be hurt by using a HOST that is not compliant. It is the responsiblity of the user to tell the HOST-OS what it needs to do. Especially if one of the OSes can not be intelligent enough to adpat to the changes.
Andre,
I am not going to debate whether what they do is good or bad, there's arguments either
way for the value in being able to detect a corrupted boot sector. Unfortunately, this is how all the installed NetWare versions on planet Earth behave. If someone is rearranging a partition table and fills out these values wrong, it will make the drive unreadable to NetWare, and make it look like Linux just corrupted the drive (since Linux will get blamed). The disk
tools should observe each OS's weirdness if it may potentially change values in this
table and cause data loss.
Jeff
Quoted 7 lines
Regards,
Andre Hedrick
Linux ATA Development
ASL Kernel Development
--------------------------------------------------------------------------
---
Quoted 9 lines
ASL, Inc. Toll free: 1-877-ASL-3535 1757 Houret Court Fax: 1-408-941-2071 Milpitas, CA 95035 Web: www.aslab.com-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 13 lines · Jeff V. Merkey
Please also check vger.timpanogas.org/nwfs/nwfs.tar.gz:disk.c for NetWare specific calculations of the CHS values, a different method is used for NetWare partitions vs. everything else (Novell just had to be different).
Quoted 9 lines · Andreas Jellinghaus
Quoted 8 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
Good. I added this to
http://www.win.tue.nl/~aeb/partitions/partition_types-2.html#above1024chs
Now that I looked at this disk.c anyway: it has a table of partition types, and it seems I collect these.
(See http://www.win.tue.nl/~aeb/partitions/partition_types-1.html ) Are types 57 and 77, labeled "VNDI Partition", actually in use?
Andries
Quoted 16 lines · Guest section DW
Quoted 13 lines · Jeff V. Merkey
Please also check vger.timpanogas.org/nwfs/nwfs.tar.gz:disk.c for NetWare specific calculations of the CHS values, a different method is used for NetWare partitions vs. everything else (Novell just had to be different).
Quoted 9 lines · Andreas Jellinghaus
Quoted 8 lines
for partitions not in the first 8gb of a harddisk, what should the c/h/s start and end value be ?
most fdisks seem to set start and end to 255/63/1023. but partition magic creates partitions with start set to 0/1/1023 and end set to 255/63/1023, and detects a problem if start is set to 255/63/1023.
Quoted 7 lines
Good. I added this to
http://www.win.tue.nl/~aeb/partitions/partition_types-2.html#above1024chsNow that I looked at this
disk.canyway: it has a table of partition types, and it seems I collect these.
(See http://www.win.tue.nl/~aeb/partitions/partition_types-1.html ) Are types 57 and 77, labeled "VNDI Partition", actually in use?
No. They are not. 65, and 77 are the ones in use. Novell was using 67 for Wolf Mountain, but for NSS, they are exclusively using "69" (I know who at Novell picked this number, and I'll give you three guesses what is always on his mind).
Jeff
Quoted 2 lines
Andries
Quoted 7 lines · Jeff V. Merkey
Quoted 2 lines · Guest section DW
(See http://www.win.tue.nl/~aeb/partitions/partition_types-1.html ) Are types 57 and 77, labeled "VNDI Partition", actually in use?
No. They are not. 65, and 77 are the ones in use. Novell was using 67 for Wolf Mountain, but for NSS, they are exclusively using 69.
Wait! 57 and 77 are not in use, but 65 and 77 are? (Is the second 77 a typo for 66 or 67?)
A lot of partition IDs are attributed to Novell.
64 (Netware 286) and 65 (Netware 386) are well established, and you tell me 66 is Netware SMS, 67 is Wolf Mountain and 69 is Netware NSS. But also 51 and 68 occur in reports. Do you know anything about those?
Andries
----- Original Message -----
From: "Guest section DW" <[email protected]>
To: "Jeff V. Merkey" <[email protected]>
Cc: "Jeff V. Merkey" <[email protected]>; "Andreas Jellinghaus" <[email protected]>; <[email protected]>; <[email protected]>
Sent: Monday, February 26, 2001 1:11 PM
Subject: Re: partition table: chs question
Quoted 9 lines · Jeff V. Merkey
Quoted 7 lines · Guest section DW
Quoted 3 lines
(See http://www.win.tue.nl/~aeb/partitions/partition_types-1.html ) Are types 57 and 77, labeled "VNDI Partition", actually in use?
No. They are not. 65, and 77 are the ones in use. Novell was using 67 for Wolf Mountain, but for NSS, they are exclusively using 69.
Quoted 7 lines
Wait! 57 and 77 are not in use, but 65 and 77 are? (Is the second 77 a typo for 66 or 67?)
A lot of partition IDs are attributed to Novell.
64 (Netware 286) and 65 (Netware 386) are well established, and you tell me 66 is Netware SMS, 67 is Wolf Mountain and 69 is Netware NSS. But also 51 and 68 occur in reports. Do you know anything about those?
Novell is assigned block 60-70 by some committee way back in the mid-1980's.
51 is not legal for them, I would like to look at this one. Any numbers in
range 60-70 they can and do use, though most are experimental. 66 and 64 are no longer used, but older stuff may use them.
77 is one we are using internally for M2FS/M2CS partitions. VNDI can be dropped.
:-)
Jeff
Quoted 2 lines
Andries