via-rhine DFE-530TX rev A1
It seems as though my card will not reset anymore after running windows 98, even after a cold boot, and recompiling the kernel. Below is the output of dmesg, lspci -n and ifconfig. Does anyone have any ideas? (please cc replies)
Linux version 2.4.5 (root@rocket) (gcc version 2.95.3 20010315 (release)) #4 Tue May 29 13:34:48 EDT 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017ff0000 (usable)
BIOS-e820: 0000000017ff0000 - 0000000017ff8000 (ACPI data)
BIOS-e820: 0000000017ff8000 - 0000000018000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 98288
zone(0): 4096 pages.
zone(1): 94192 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=2.4.5 ro root=342 BOOT_FILE=/boot/vmlinuz-2.4.5 hdd=ide-scsiide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 866.680 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1730.15 BogoMIPS
Memory: 384368k/393152k available (1079k kernel code, 8396k reserved, 348k data, 204k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000 CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 CPU: Common caps: 0383f9ff 00000000 00000000 00000000 CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting
PCI: Disabled enhanced CPU to PCI posting #2
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.80x378: FIFO is 16 bytes0x378: writeIntrThreshold is 80x378: readIntrThreshold is 80x378: PWord is 8 bits0x378: Interrupts are ISA-Pulses0x378: ECP port cfgA=0x10 cfgB=0x000x378: ECP settings irq=<none or set by other means> dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
parport0: cpp_daisy: aa5500ff(98)
parport0: assign_addrs: aa5500ff(98)
parport0: Printer, Canon BJC-1000parport_pc: Via 686A parallel port: io=0x378
pty: 256 Unix98 ptys configured
Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: queued sectors max/low 255210kB/124138kB, 768 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 39VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
hda: FUJITSU MPG3204AH, ATA DISK drive
hdb: WDC WD307AA, ATA DISK drive
hdc: CDU5211, ATAPI CD/DVD-ROM drive
hdd: MATSHITA CD-RW CW-7586, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40031712 sectors (20496 MB) w/2048KiB Cache, CHS=2491/255/63
hdb: 60074784 sectors (30758 MB) w/2048KiB Cache, CHS=3739/255/63
hdc: ATAPI 52X CD-ROM drive, 120kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1
hdb: hdb1 hdb2 hdb3 < hdb5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
via-rhine.c:v1.08b-LK1.1.8 4/17/2000 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Found IRQ 10 for device 00:11.0
PCI: The same IRQ used for device 00:07.2
eth0: VIA VT6102 Rhine-II at 0xd000, 00:00:00:00:00:00, IRQ 10. PPP generic driver version 2.4.1
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xe8000000
[drm] AGP 0.99 on VIA Apollo Pro @ 0xe8000000 64MB
[drm] Initialized tdfx 1.0.0 20000928 on minor 63
[drm] AGP 0.99 on VIA Apollo Pro @ 0xe8000000 64MB
[drm] Initialized radeon 1.0.0 20010105 on minor 62
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: CD-RW CW-7586 Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 8x/32x writer cd/rw xa/form2 cdda tray
es1371: version v0.30 time 20:29:48 May 28 2001
PCI: Found IRQ 11 for device 00:0e.0
es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02
es1371: found es1371 rev 2 at io 0xd800 irq 11
es1371: features: joystick 0x0ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)ip_tables: (c)2000 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 204k freed
Adding Swap: 393552k swap-space (priority -1)
pppoe uses obsolete (PF_INET,SOCK_PACKET)
VFS: Disk change detected on device ide1(22,0)
VFS: Disk change detected on device ide1(22,0)
cdrom: This disc doesn't have any tracks I recognize!
00:00.0 Class 0600: 1106:0691 (rev c4)
00:01.0 Class 0604: 1106:8598
00:07.0 Class 0601: 1106:0686 (rev 40)
00:07.1 Class 0101: 1106:0571 (rev 06)
00:07.2 Class 0c03: 1106:3038 (rev 16)
00:07.4 Class 0c05: 1106:3057 (rev 40)
00:0e.0 Class 0401: 1274:5880 (rev 02)
00:10.0 Class 0780: 125d:2898 (rev 03)
00:11.0 Class 0200: 1106:3065 (rev 42)
01:00.0 Class 0300: 1002:5246
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100
Interrupt:10 Base address:0xd000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
Quoted 4 lines · Daniel
It seems as though my card will not reset anymore after running windows 98, even after a cold boot, and recompiling the kernel. Below is the output of dmesg, lspci -n and ifconfig. Does anyone have any ideas? (please cc replies)
Have you tried cutting power to the machine? (ie physically unplugging it)
Someone has claimed that the chip may not reset otherwise. As it is Wake-On-Lan capable, that sort of makes sense - it needs to be not entirely dead.
Quoted 5 lines
via-rhine.c:v1.08b-LK1.1.8 4/17/2000 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Found IRQ 10 for device 00:11.0
PCI: The same IRQ used for device 00:07.2
eth0: VIA VT6102 Rhine-II at0xd000, 00:00:00:00:00:00, IRQ 10.
[snip]
Quoted 1 line
00:11.0 Class 0200: 1106:3065 (rev 42)
Are you sure the card is marked rev-A1 and not rev-B1? I was hoping DFE-530TXs with vt6102 were all rev-B1.
Can you check what's printed on the card and send me the markings on the main chips?
(one is probably marked DL10030, DL10030A or possibly vt6102 with a big VIA logo)
/Urban