Skip to contentSkip to conversation

ssh and cs LAG]

Fwd: Re: Hariett Jones 5 participants 7 messages Oct 13, 2004

lore
Share & tools
lore
#0 lore raw

Got some solutions myself.

LAG is caused by :
NETDEV WATCHDOG eth0 timeout

this is caused bacause of problems with rtl8139 network card in kernel 2.6.x

Solutions :
1.add in lilo.conf : append="noapic"
2.turn apic off in bios
3.if u have 2 rtl8139 cards, then exchange one with some other card type (chipset)

btw. all above was found in various polish forums, but none has worked for me. im switching kernel back to 2.4.22, and will report later .

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Switching back to older kernel won't do much.
I've had this problem much earlier when using two NICs of the same type. I couldn't figure out why, but there ARE problems is many ways when using two cards of the same type. I had problems with sharing, with routing, etc. etc.
Best solution is to use different NICs... don't ask me why... I just found out that this will solve the problems...

-----Ursprüngliche Nachricht-----
Von: [email protected] [mailto:[email protected]] Im Auftrag von Hariett Jones
Gesendet: Mittwoch, 13. Oktober 2004 22:13
An: [email protected]
Betreff: [Fwd: Re: [LARTC] ssh and cs LAG]

Got some solutions myself.

LAG is caused by :
NETDEV WATCHDOG eth0 timeout

this is caused bacause of problems with rtl8139 network card in kernel 2.6.x

Solutions :
1.add in lilo.conf : append="noapic"
2.turn apic off in bios
3.if u have 2 rtl8139 cards, then exchange one with some other card type

(chipset)

btw. all above was found in various polish forums, but none has worked for me. im switching kernel back to 2.4.22, and will report later .

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Hariett Jones
Quoted 8 lines · Stephan M. Ott

Switching back to older kernel won't do much.
I've had this problem much earlier when using two NICs of the same type. I couldn't figure out why, but there ARE problems is many ways when using two cards of the same type. I had problems with sharing, with routing, etc. etc.
Best solution is to use different NICs... don't ask me why... I just found out that this will solve the problems...

It's probably the machine. I have three rtl8139 based cards in a box and it's been working flawlessly for six months. I've used 2.4 series kernels and 2.6 series kernels on the box in question.

Signature · 8 lines
Jason Boxman
Perl Programmer / *NIX Systems Administrator
Shimberg Center for Affordable Housing | University of Florida
http://edseek.com/ - Linux and FOSS stuff

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Hariett Jones

Hariett,

Switching to the 2.4 kernel is not an option as this is a production server.

The machine has a dual Intel PRO/1000 NIC.

The machine usies grub, not lilo, but that doesn't really matter. Not sure if APIC is an issue or not.

Thanks for your help.

Mike

Quoted 14 lines · Hariett Jones

Got some solutions myself.

LAG is caused by :
NETDEV WATCHDOG eth0 timeout

this is caused bacause of problems with rtl8139 network card in kernel 2.6.x

Solutions :
1.add in lilo.conf : append="noapic"
2.turn apic off in bios
3.if u have 2 rtl8139 cards, then exchange one with some other card type (chipset)

Quoted 9 lines

btw. all above was found in various polish forums, but none has worked for me. im switching kernel back to 2.4.22, and will report later .

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Hariett Jones
Quoted 7 lines · Hariett Jones

Got some solutions myself.

LAG is caused by :
NETDEV WATCHDOG eth0 timeout

this is caused bacause of problems with rtl8139 network card in kernel 2.6.x

I had to unselect SMP in kernel config to get my rtl8139 + PCI modem to work with 2.6.8.1

Andy.

Quoted 6 lines

Solutions :
1.add in lilo.conf : append="noapic"
2.turn apic off in bios
3.if u have 2 rtl8139 cards, then exchange one with some other card type (chipset)

Quoted 9 lines

btw. all above was found in various polish forums, but none has worked for me. im switching kernel back to 2.4.22, and will report later .

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to Hariett Jones

We had no problems with smp on 2.6.8.3, and since this cpu supports hyperthreading we enjoy a *big* power boost using smp. :)

Mike

Quoted 34 lines · Andy Furniss
Quoted 7 lines · Hariett Jones

Got some solutions myself.

LAG is caused by :
NETDEV WATCHDOG eth0 timeout

this is caused bacause of problems with rtl8139 network card in kernel 2.6.x

I had to unselect SMP in kernel config to get my rtl8139 + PCI modem to work with 2.6.8.1

Andy.

Quoted 12 lines

Solutions :
1.add in lilo.conf : append="noapic"
2.turn apic off in bios
3.if u have 2 rtl8139 cards, then exchange one with some other card type (chipset)

btw. all above was found in various polish forums, but none has worked for me. im switching kernel back to 2.4.22, and will report later .

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to Hariett Jones
Quoted 2 lines · Mike Slinn

We had no problems with smp on 2.6.8.3, and since this cpu supports hyperthreading we enjoy a *big* power boost using smp. :)

I think it's this box(via p200) + rtl8139 that's the problem - it's always been a bit flakey. I have the same card in a PII350 intel440bx and it has always been OK.

Andy.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/