writing audiowerk driver (philips saa7146a), some questions
below is a message i sent earlier, but with the wrong email address:
----
writing audiowerk driver (philips saa7146a), some questions
hi,
i have finally been able to get the information i need to be able to write a driver for the emagic audiowerk8 audio interface. now since i am not an experienced kernel programmer and have not even done audio programming (apart from midi), i have some questions.
- should i use the normal double buffered aproach or does having more than 2 buffers have advantages?
- what is normally called the latency of an audio interface for output? is this the total size of the buffers or (in the case of double buffered
io)
only one buffer? i'm thinking it is the total buffer size and this would make using more than 2 buffers have a better latency/interrupt response time ratio, right?
- should setting the buffer size and number be done on modules loading or should it be possible to change it after that? the saa7146 doesn't need contiguous memory since it has a mmu.
- where can i find documentation on writing alsa drivers? what would be the best driver source to use for documentation?
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows for the sample rate to be adjusted when receiving audio using rtp.
- the audiowerk8 uses three dma channels: one for input and two for output. should i just wake a process that is blocking on a read() from the input
dma
interrupt or should i wait until all three dma channels are ready and then unblock all read()/write() processes? should unblocking the processes be done
from bottom half?
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Quoted 6 lines · Martijn Sipkema
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows for the sample rate to be adjusted when receiving audio using rtp.
Can the frequency be changed without stopping (no loss of sound)? If so it is an interesting feature, but I am not sure if supported by ALSA.
Best regards,
--
Tomasz Motylewski
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Quoted 5 lines
Quoted 5 lines
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows for
the
Quoted 3 lines
Quoted 1 line
sample rate to be adjusted when receiving audio using rtp.
Can the frequency be changed without stopping (no loss of sound)?
yes
Quoted 2 lines
If so it is
an interesting feature, but I am not sure if supported by ALSA.
perhaps it could be added?
in EASI every driver has a number of supported sample rates and an associated pitch range.
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
At Fri, 31 May 2002 11:38:41 +0100,
Quoted 10 lines · Martijn Sipkema
below is a message i sent earlier, but with the wrong email address:
----
writing audiowerk driver (philips saa7146a), some questions
hi,
Quoted 8 lines
i have finally been able to get the information i need to be able to write a driver for the emagic audiowerk8 audio interface. now since i am not an experienced kernel programmer and have not even done audio programming (apart from midi), i have some questions.
- should i use the normal double buffered aproach or does having more than 2 buffers have advantages?
most of pci drivers use a linear contigous buffer for pcm (per stream).
the scatter-gather buffer is not supported yet on alsa (as a mid/high level layer -- it would be possible if you write all on the low-level layer).
the buffer is accessed directly via mmap as long as it's supported.
Quoted 6 lines
- what is normally called the latency of an audio interface for output? is this the total size of the buffers or (in the case of double buffered
io)
only one buffer? i'm thinking it is the total buffer size and this would make using more than 2 buffers have a better latency/interrupt response time ratio, right?
but if you have double buffer, isn't it difficult to handle mmap? also i don't think double-buffer (that i'm not sure whether you mean here "period" in the sense of alsa, or really double-buffering as in graphics) leads to better latency. of course my guess may be wrong.
Quoted 3 lines
- should setting the buffer size and number be done on modules loading or should it be possible to change it after that? the saa7146 doesn't need contiguous memory since it has a mmu.
the buffer size and numbers are specified by each application. at set-up stage, an application and driver commnucate with each other to find the preferable condition. the driver answers the hardware restriction to the application which inquires the condition. then the hardware is "prepared" actually, by calling prepare callback.
in most cases, the hardawre restriction (condition) can be described in snd_pcm_hardware_t struct, which is passed to the runtime instance at open callback. the struct contains most of important conditions, such as supported formats, rates, channels, max buffers, etc. also, you can define more complicated conditions, if necessary.
Quoted 2 lines
- where can i find documentation on writing alsa drivers? what would be the best driver source to use for documentation?
hmm.. it depends on the hardware design...
Quoted 6 lines
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows for the sample rate to be adjusted when receiving audio using rtp.
basically no (at least not tested). but i think it's not too difficult to support it. we can assign a control per pcm. you'll need to change runtime->rate dynamically according to the current rate, so that the tick interrupt handler calculates the time properly.
Quoted 7 lines
- the audiowerk8 uses three dma channels: one for input and two for output. should i just wake a process that is blocking on a
read()from the input
dma
interrupt or should i wait until all three dma channels are ready and then unblock all read()/write() processes? should unblocking the processes be done
from bottom half?
it's a job of alsa's high-level layer.
the lowlevel routines don't have to handle sleep()/wakeup(). just call snd_pcm_period_elapsed() in the interrupts routine when the certain amount of samples have been processed.
Takashi
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Quoted 13 lines
Quoted 2 lines
- should i use the normal double buffered aproach or does having more than 2 buffers have advantages?
most of pci drivers use a linear contigous buffer for pcm (per stream).
the scatter-gather buffer is not supported yet on alsa (as a mid/high level layer -- it would be possible if you write all on the low-level layer).
the buffer is accessed directly via mmap as long as it's supported.Quoted 2 lines
- what is normally called the latency of an audio interface for output? is this the total size of the buffers or (in the case of double
buffered
Quoted 2 lines
Quoted 2 lines
io)
only one buffer? i'm thinking it is the total buffer size and this
would
Quoted 7 lines
Quoted 2 lines
make using more than 2 buffers have a better latency/interrupt response time ratio, right?
but if you have double buffer, isn't it difficult to handle mmap? also i don't think double-buffer (that i'm not sure whether you mean here "period" in the sense of alsa, or really double-buffering as in graphics) leads to better latency. of course my guess may be wrong.
i did not mean two buffers actually, perhaps the alsa term is period? with double buffering i meant having the saa7146 interrupt at half buffer.
the saa7146 uses a single contiguous buffer, optionally using an mmu (so then the buffer is not actually contiguous in physical memory).
thus, having more than two periods is advantageous?
Quoted 2 lines
Quoted 2 lines
- should setting the buffer size and number be done on modules loading or should it be possible to change it after that? the saa7146 doesn't
need
Quoted 9 lines
Quoted 1 line
contiguous memory since it has a mmu.
the buffer size and numbers are specified by each application. at set-up stage, an application and driver commnucate with each other to find the preferable condition. the driver answers the hardware restriction to the application which inquires the condition. then the hardware is "prepared" actually, by calling prepare callback.
Quoted 6 lines
in most cases, the hardawre restriction (condition) can be described in
snd_pcm_hardware_tstruct, which is passed to the runtime instance at open callback. the struct contains most of important conditions, such as supported formats, rates, channels, max buffers, etc. also, you can define more complicated conditions, if necessary.
so if the application can set the buffer at set-up stage, it is best to allocate
buffer memory at that time?
Quoted 5 lines
Quoted 5 lines
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows for
the
Quoted 7 lines
Quoted 1 line
sample rate to be adjusted when receiving audio using rtp.
basically no (at least not tested). but i think it's not too difficult to support it. we can assign a control per pcm. you'll need to change
runtime->ratedynamically according to the current rate, so that the tick interrupt handler calculates the time properly.
again, i am not (yet) familiar with alsa, so i am not sure what runtime->rate is
or what you mean with the tick interrupt handler (where can i find documentation
on this?), but i think 'pitch' is meant as a deviation from the nominal sample rate
and setting a large deviation can be thought of as a bad dac/adc?
Quoted 1 line
Quoted 1 line
- the audiowerk8 uses three dma channels: one for input and two for
output.
Quoted 1 line
Quoted 1 line
should i just wake a process that is blocking on a
read()from the
input
Quoted 2 lines
Quoted 2 lines
dma
interrupt or should i wait until all three dma channels are ready and
then
Quoted 1 line
Quoted 1 line
unblock all read()/write() processes? should unblocking the processes
be
Quoted 7 lines
Quoted 2 lines
done
from bottom half?it's a job of alsa's high-level layer.
the lowlevel routines don't have to handle sleep()/wakeup(). just callsnd_pcm_period_elapsed()in the interrupts routine when the certain amount of samples have been processed.
is there any documentation on this?
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
At Fri, 31 May 2002 14:05:20 +0100,
Quoted 21 lines · Martijn Sipkema
Quoted 4 lines
Quoted 3 lines
- should i use the normal double buffered aproach or does having more than 2 buffers have advantages?
Quoted 10 lines
most of pci drivers use a linear contigous buffer for pcm (per stream).
the scatter-gather buffer is not supported yet on alsa (as a mid/high level layer -- it would be possible if you write all on the low-level layer).
the buffer is accessed directly via mmap as long as it's supported.Quoted 2 lines
- what is normally called the latency of an audio interface for output? is this the total size of the buffers or (in the case of double
buffered
Quoted 2 lines
Quoted 2 lines
io)
only one buffer? i'm thinking it is the total buffer size and thiswould
Quoted 3 lines
Quoted 2 lines
make using more than 2 buffers have a better latency/interrupt response time ratio, right?
Quoted 7 lines
Quoted 4 lines
but if you have double buffer, isn't it difficult to handle mmap? also i don't think double-buffer (that i'm not sure whether you mean here "period" in the sense of alsa, or really double-buffering as in graphics) leads to better latency. of course my guess may be wrong.
i did not mean two buffers actually, perhaps the alsa term is period? with double buffering i meant having the saa7146 interrupt at half buffer.
then it's called "two periods per buffer" in alsa.
Quoted 2 lines
the saa7146 uses a single contiguous buffer, optionally using an mmu (so then the buffer is not actually contiguous in physical memory).
ok, it's similar to trident or emu10k1, which uses also its own TLB. for pcm, both of them use contigous memory buffer, though.
Quoted 1 line
thus, having more than two periods is advantageous?
let the choice left to application.
more periods would be more stable even for interrupts delay, but of course would have longer latency.
Quoted 19 lines
Quoted 2 lines
Quoted 2 lines
- should setting the buffer size and number be done on modules loading or should it be possible to change it after that? the saa7146 doesn't
need
Quoted 9 lines
Quoted 1 line
contiguous memory since it has a mmu.
the buffer size and numbers are specified by each application. at set-up stage, an application and driver commnucate with each other to find the preferable condition. the driver answers the hardware restriction to the application which inquires the condition. then the hardware is "prepared" actually, by calling prepare callback.
Quoted 6 lines
in most cases, the hardawre restriction (condition) can be described in
snd_pcm_hardware_tstruct, which is passed to the runtime instance at open callback. the struct contains most of important conditions, such as supported formats, rates, channels, max buffers, etc. also, you can define more complicated conditions, if necessary.
Quoted 3 lines
so if the application can set the buffer at set-up stage, it is best to allocate
buffer memory at that time?
yes. however, usually a chunk of memory is pre-allocated at the boot time (i.e. when the module is loaded), to avoid possible memory
fragmentation. you can find snd_pci_preallocate_buffer() is called
where the pcm is created via snd_pcm_new().
Quoted 14 lines
Quoted 5 lines
Quoted 5 lines
- does alsa allow varipitch? i think the new rme cards are supposed to have this feature and the audiowerk8 has it, i.e. it can change its
sampling
rate from about 37700 to 58200 hz while running in 1hz increments. this allows for sync to video/tape/midi or whatever. or it allows forthe
Quoted 7 lines
Quoted 1 line
sample rate to be adjusted when receiving audio using rtp.
basically no (at least not tested). but i think it's not too difficult to support it. we can assign a control per pcm. you'll need to change
runtime->ratedynamically according to the current rate, so that the tick interrupt handler calculates the time properly.
Quoted 7 lines
again, i am not (yet) familiar with alsa, so i am not sure what
runtime->rateis
or what you mean with the tick interrupt handler (where can i find documentation
on this?), but i think 'pitch' is meant as a deviation from the nominal sample rate
and setting a large deviation can be thought of as a bad dac/adc?
there is a runtime instance for a pcm stream, and this holds the informaton such as the current rate, channels, formats, etc. there is no pitch parameter implemented in alsa, but this can be added easily into the runtime instance, if inevitablly necessary.
alsa pcm engine invokes a timer interrupt to update the "tick", and this tick is determined using the rate of the runtime instance. if you change the rate value dynamically during playback, then the tick interrupt will be wrongly scheduled, and leads to wrong detection of under/overrun.
Quoted 12 lines
Quoted 1 line
Quoted 1 line
- the audiowerk8 uses three dma channels: one for input and two for
output.
Quoted 1 line
Quoted 1 line
should i just wake a process that is blocking on a
read()from theinput
Quoted 2 lines
Quoted 2 lines
dma
interrupt or should i wait until all three dma channels are ready andthen
Quoted 1 line
Quoted 1 line
unblock all read()/write() processes? should unblocking the processes
be
Quoted 3 lines
Quoted 2 lines
done
from bottom half?
Quoted 6 lines
Quoted 4 lines
it's a job of alsa's high-level layer.
the lowlevel routines don't have to handle sleep()/wakeup(). just callsnd_pcm_period_elapsed()in the interrupts routine when the certain amount of samples have been processed.is there any documentation on this?
not (yet)... i once posted a very brief summary to alsa devel ML. please check out the archive.
Takashi
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Quoted 4 lines
there is a runtime instance for a pcm stream, and this holds the informaton such as the current rate, channels, formats, etc. there is no pitch parameter implemented in alsa, but this can be added easily into the runtime instance, if inevitablly necessary.
i don't think the audiowerk is the only card capable of varipitch, though most cards don't support it, but it is a nice feature and since alsa is supposed to be advanced... :)
Quoted 5 lines
alsa pcm engine invokes a timer interrupt to update the "tick", and this tick is determined using the rate of the runtime instance. if you change the rate value dynamically during playback, then the tick interrupt will be wrongly scheduled, and leads to wrong detection of under/overrun.
shouldn't the driver detect under/overrun? would a soundcard with a bad dac (as in not accurate) also cause problems?
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 1 line
Quoted 1 line
i don't think the audiowerk is the only card capable of varipitch,
though
Quoted 5 lines
Quoted 2 lines
most cards don't support it, but it is a nice feature and since alsa is supposed to be advanced... :)
many consumer chips support in fact, too, such as emu10k1, ymfpci, cs46xx (also trident?) sbawe and gus have pcms using synth
so it will be added? the best would be to have a pitch range for every nominal sample rate as in EASI
http://www.emagic.de/english/support/easi/index.html )
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
alsa pcm engine invokes a timer interrupt to update the "tick", and this tick is determined using the rate of the runtime instance. if you change the rate value dynamically during playback, then the tick interrupt will be wrongly scheduled, and leads to wrong detection of under/overrun.
Quoted 7 lines
Quoted 1 line
shouldn't the driver detect under/overrun?
yes. that's why i mentioned above. if you don't change rate value in runtime instance, then the alsa driver tries to schedule tick interval as if it's not changed. and this causes inconsistency between the real-playback and tick time, eventually leading to a bogus detection of under/overrun.
i am lost. a under/overrun could (should) be detected from the interrupt handler
for the card dma channel (period interrupt), right? that would never fail.
Quoted 5 lines
Quoted 2 lines
would a soundcard with a bad dac (as in not accurate) also cause problems?
if the hardware is too inaccurate (e.g. accumulated error over more
than HZ), then, yes. but i don't think this may happen.
i am afraid i don't understand this and i don't now where i can find documentation
on it. how do other driver writers do this? read the source? or an API reference?
is there no overview on the architecture? reading driver source code is not the
easiest or fastest way to understand what's going on, if it is at all possible to
understand without knowledge of the specific hardware.
does hardware allow to have a device specific kernel driver with an associated
device specific user-space part? this would be much easier to implement for me
than an alsa kernel driver i think.
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Quoted 2 lines · Martijn Sipkema
i have finally been able to get the information i need to be able to write a driver for the emagic audiowerk8 audio interface.
Did emagic give you information about the hardware, or is it from some other source?
Signature · 9 lines
Bob Ham: [email protected] http://pkl.net/~node/ My music: http://mp3.com/obelisk_uk GNU Hurd: http://hurd.gnu.org/ _______________________________________________________________ Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm
Re: Fw: writing audiowerk driver (philips saa7146a),some questions
Quoted 5 lines
Quoted 2 lines
i have finally been able to get the information i need to be able to write a driver for the emagic audiowerk8 audio interface.
Did emagic give you information about the hardware, or is it from some other source?
Emagic pointed me to http://www.landamore.com/audiowerk.html
All the information i have is the driver and the philips SAA7146A documentation. Although more information would help, this is at least enough to get sound in/out the Audiowerk. I emailed the author of this driver, but he has not (yet) replied.
--martijn
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference August 25-28 in Las Vegas -- http://devcon.sprintpcs.com/adp/index.cfm