cpufreq/powernowd limiting CPU frequency on kernels >=2.6.16
Most recent kernel where this bug did not occur:2.6.15 Distribution:Ubuntu64bit
Hardware Environment: X2 3800+, DFI NF4 Ultra-D, X800GT
Software Environment:
Problem Description: I overclocked via bios my cpu (factory: 200x10) to 2565mhz (285x9), and I haven't any problems 'til 2.6.15, it goes down to 285x5 in idle and up to 285x9 in full load. If I upgrade to a newer kernel, it says 1ghz in idle and 1,8ghz in full load (I wonder it takes the fsb value, that is 200mhz, directly form cpu and not from the bios, so it assumes 200x5 in idle and 200x9 in full load)
flapane@a64:~$ cpufreq-info cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: powernow-k8 CPUs which need to switch frequency at the same time: 0 1 hardware limits: 1000 MHz - 1.80 GHz available frequency steps: 1.80 GHz, 1000 MHz available cpufreq governors: userspace, powersave, ondemand, conservative, performance current policy: frequency should be within 1000 MHz and 1.80 GHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 1000 MHz. analyzing CPU 1: driver: powernow-k8 CPUs which need to switch frequency at the same time: 0 1 hardware limits: 1000 MHz - 1.80 GHz available frequency steps: 1.80 GHz, 1000 MHz available cpufreq governors: userspace, powersave, ondemand, conservative, performance current policy: frequency should be within 1000 MHz and 1.80 GHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 1000 MHz.
Steps to reproduce:
simply compile a kernel >=2.6.16 and try to overclock your cpu from the bios raising the FSB (or HT)
Flavio
www.flapane.com
From: Inter filmati <[email protected]>
Date: Thu, Oct 26, 2006 at 07:08:20PM +0200
Quoted 6 lines
Most recent kernel where this bug did not occur:2.6.15 Distribution:Ubuntu64bit
Hardware Environment: X2 3800+, DFI NF4 Ultra-D, X800GT Software Environment:
Problem Description: I overclocked via bios my cpu (factory: 200x10) to 2565mhz
this ugly quoting would be prevented if you used a line length of 72.
Quoted 10 lines
(285x9), and I haven't any problems 'til 2.6.15, it goes down to 285x5 in idle
and up to 285x9 in full load. If I upgrade to a newer kernel, it says 1ghz in
idle and 1,8ghz in full load (I wonder it takes the fsb value, that is 200mhz,
directly form cpu and not from the bios, so it assumes 200x5 in idle and 200x9
in full load)
Quoted 4 lines
Steps to reproduce:
simply compile a kernel >=2.6.16 and try to overclock your cpu from the bios raising the FSB (or HT)
No so simple: I mildly overclocked my FSB, from 2400 to 2520 MHz and I see:
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please.
analyzing CPU 0:
driver: powernow-k8
CPUs which need to switch frequency at the same time: 0 1 hardware limits: 1000 MHz - 2.40 GHz
available frequency steps: 2.40 GHz, 2.20 GHz, 2.00 GHz, 1.80 GHz, 1000 MHz available cpufreq governors: ondemand, powersave, performance current policy: frequency should be within 1000 MHz and 2.40 GHz.
The governor "ondemand" may decide which speed to use within this range.
current CPU frequency is 1000 MHz.
analyzing CPU 1:
[the same]
from demsg:time.c: Detected 2520.575 MHz processor.
Which means that my X2 4600+ works just fine, but after overclocking cpufreq restores it to the FSB that it should run on.
If you care about that changed, try to find out what patch caused this, but in general, there's no support for overclocking in the kernel, and bugreports from overclocked systems are frowned upon.
Kind regards,
Jurriaan
Signature · 4 lines
"What sort of timeframe did you have in mind?" "An immediate one," I said. "The immediater the better." Jim Butcher - Blood Rites Debian (Unstable) GNU/Linux 2.6.18-mm3 2x5042 bogomips load 0.91
----- Original Message ----- From: <[email protected]>
To: "Inter filmati" <[email protected]>
Cc: <[email protected]>
Sent: Thursday, October 26, 2006 7:41 PM
Subject: Re: cpufreq/powernowd limiting CPU frequency on kernels >=2.6.16
Quoted 7 lines
Which means that my X2 4600+ works just fine, but after overclocking cpufreq restores it to the FSB that it should run on.
If you care about that changed, try to find out what patch caused this, but in general, there's no support for overclocking in the kernel, and bugreports from overclocked systems are frowned upon.
It would be kind to find out why the problem seems to show only from 2.6.16 and not before, unfortunately I ain't so skilled to investigate into cpufreq source.
---
Flavio
www.flapane.com
From: Inter filmati <[email protected]>
Date: Thu, Oct 26, 2006 at 07:59:41PM +0200
Quoted 9 lines
Quoted 5 lines
If you care about that changed, try to find out what patch caused this, but in general, there's no support for overclocking in the kernel, and bugreports from overclocked systems are frowned upon.
It would be kind to find out why the problem seems to show only from 2.6.16 and not before, unfortunately I ain't so skilled to investigate into cpufreq source.
You could start by trying 2.6.16-rc1, -rc2, -rc3 and find out in which kernel it changed. Then, read the changelog for that patch to find out what changed in the cpufreq driver. So far, no great skill required. Then, post here, mentioning which patch caused the different behaviour.
Jurriaan
Signature · 4 lines
Despite the best efforts of a quantum bigfoot drive (yes I know everyone told me they suck, now I know they were right) 2.1.109ac1 is now available Alan Cox announcing Linux 2.1.109ac1 Debian (Unstable) GNU/Linux 2.6.18-mm3 2x5042 bogomips load 0.91