Skip to contentSkip to conversation

PPC405GPWalnutPciBusMaster

DISCUSSION Hideo Noda 5 participants 6 messages Apr 19, 2001 – May 16, 2001

lore
Share & tools
lore

Hideo Noda

author
#0 lore raw

Hi,

I am trying to install Intel eepro100 onto WalnutPPC405GP. Basic PCI settings seem good but no frame is transmitted. The environment is WalnutPPC305GP with HardHatLinux 2.4.2 from MonraVista.

I can read or write eepro configuration registers and other control registers via PCI memory space.
But Bus Master operations do not seem functional. I am confirmed that MASTER operation bit in eepro100 is enabled.
I think some more settings are needed for PPC405GP built-in PCI control registers and/or Walnut board jumpers/dipswitches.

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

Thanks in advance,

Hideo

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw
Quoted 2 lines · Hideo Noda

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

I have tried and failed. I have other things to work on right now so I have just delayed looking into it anymore until the 2.0 CDK comes out. I think that should be by the end of the month.

I think there is a problem with the virt_to_phys matching the PTM1/BAR1. In the preliminary 405gp docs that I have Fig 17-59 on page 17-62 give a good overview on how things need to be setup on the chip, but I am not sure on what the values need to be.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#2 lore raw
Quoted 9 lines · Hideo Noda
Quoted 2 lines

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

I have tried and failed. I have other things to work on right now so I have just delayed looking into it anymore until the 2.0 CDK comes out. I think that should be by the end of the month.

Quoted 5 lines

I think there is a problem with the virt_to_phys matching the PTM1/BAR1. In the preliminary 405gp docs that I have Fig 17-59 on page 17-62 give a good overview on how things need to be setup on the chip, but I am not sure on what the values need to be.

Which bootloader/firmware are you using? The pci configuration should be done within the bootloader. If you are using PPCBoot, I am not shure if the configuration is correct regarding the busmaster setup (although I did the port based on the IBM OpenBios). The bus master functionality was never tested - sorry for that.

Stefan.

*******************************************
esd gmbh
Vahrenwalder Str. 205
D-30165 Hannover

Phone: +49-511-37298-0
Fax:   +49-511-37298-198
email: [email protected]
www:   http://www.esd-electronics.de

*******************************************

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#3 lore raw
Quoted 15 lines · Stefan Roese
Quoted 9 lines · Hideo Noda
Quoted 2 lines

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

I have tried and failed. I have other things to work on right now so I have just delayed looking into it anymore until the 2.0 CDK comes out. I think that should be by the end of the month.

Quoted 5 lines

I think there is a problem with the virt_to_phys matching the PTM1/BAR1. In the preliminary 405gp docs that I have Fig 17-59 on page 17-62 give a good overview on how things need to be setup on the chip, but I am not sure on what the values need to be.

Quoted 5 lines

Which bootloader/firmware are you using? The pci configuration should be done within the bootloader. If you are using PPCBoot, I am not shure if the configuration is correct regarding the busmaster setup (although I did the port based on the IBM OpenBios). The bus master functionality was never tested - sorry for that.

I am just using the OpenBios for now. We will be spinning our own board within the year so I was going to delay looking into doing the PPCBoot code until then. I was able to look at the PCI registers when the kernel booted and they appeared to be OK. For the hell of it I tried to change them in the kernel and it hung during boot. I did not see in the docs the constraints on when I could change those registers. Is it possible to do it very early in the Linux boot code?
Thanks
--
Andrew May

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#4 lore raw
In reply to Hideo Noda

Now I have the same problem as you meet before.
Have you find a good solutions?
Thank you very mcuh.

machael

Quoted 15 lines

Hi,

I am trying to install Intel eepro100 onto WalnutPPC405GP. Basic PCI settings seem good but no frame is transmitted. The environment is WalnutPPC305GP with HardHatLinux 2.4.2 from MonraVista.

I can read or write eepro configuration registers and other control registers via PCI memory space.
But Bus Master operations do not seem functional. I am confirmed that MASTER operation bit in eepro100 is enabled.
I think some more settings are needed for PPC405GP built-in PCI control registers and/or Walnut board jumpers/dipswitches.

Quoted 9 lines

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

Thanks in advance,

Hideo

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#5 lore raw

Until a newer kernel is released by Monta Vista that includes a fix, you can use setpci to change the settings of the PCI bridge as follows:

setpci -s 0:0.1 14.L=0x8

Then you should be able to "insmod eepro100"...

Regards,
John

Quoted 28 lines · machael thailer

Now I have the same problem as you meet before.
Have you find a good solutions?
Thank you very mcuh.

machael

Quoted 21 lines

Hi,

I am trying to install Intel eepro100 onto WalnutPPC405GP. Basic PCI settings seem good but no frame is transmitted. The environment is WalnutPPC305GP with HardHatLinux 2.4.2 from MonraVista.

I can read or write eepro configuration registers and other control registers via PCI memory space.
But Bus Master operations do not seem functional. I am confirmed that MASTER operation bit in eepro100 is enabled.
I think some more settings are needed for PPC405GP built-in PCI control registers and/or Walnut board jumpers/dipswitches.

Has anyone tried PCI cards with BUS MASTER operations for Walnut PPC405GP?

Thanks in advance,

Hideo

------------------------------
John Cagle <[email protected]>

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/