of: add vendor prefix for Eukr��a Electromatique.
Subsystems (4)
PATCH 1/11 of: add vendor prefix for Eukr��a Electromatique.
Trivial patch to add Eukr?a Electromatique to the list of devicetree vendor prefixes.
--- .../devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
@@ -25,6 +25,7 @@ denx Denx Software Engineering emmicro EM Microelectronic epson Seiko Epson Corp. est ESTeem Wireless Modems +eukrea Eukr?a Electromatique fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc.
Signature · 1 line
1.7.9.5
PATCH 2/11 video: imxfb: Introduce regulator support.
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator support
--- drivers/video/imxfb.c | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)
drivers/video/imxfb.c +27 -0
@@ -28,6 +28,7 @@#include <linux/cpufreq.h> #include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/regulator/consumer.h> #include <linux/dma-mapping.h> #include <linux/io.h> #include <linux/math64.h>
@@ -145,6 +146,7 @@ struct imxfb_info {struct clk *clk_ipg;struct clk *clk_ahb;struct clk *clk_per; +struct regulator *reg_lcd;enum imxfb_type devtype;bool enabled;
@@ -563,12 +565,23 @@ static void imxfb_exit_backlight(struct imxfb_info *fbi)static void imxfb_enable_controller (struct imxfb_info *fbi) { +int ret;if (fbi->enabled)return ;pr_debug ("Enabling LCD controller\n" ); +if (fbi->reg_lcd) { + ret =regulator_enable (fbi->reg_lcd); +if (ret) { +dev_err (&fbi->pdev->dev, +"lcd regulator enable failed with error: %d\n" , + ret); +return ; + } + } +writel (fbi->screen_dma, fbi->regs +LCDC_SSA );/* panning offset 0 (0 pixel offset) */
@@ -597,6 +610,8 @@ static void imxfb_enable_controller(struct imxfb_info *fbi)static void imxfb_disable_controller (struct imxfb_info *fbi) { +int ret; +if (!fbi->enabled)return ;
@@ -613,6 +628,14 @@ static void imxfb_disable_controller(struct imxfb_info *fbi) fbi->enabled = false;writel (0 , fbi->regs +LCDC_RMCR ); + +if (fbi->reg_lcd) { + ret =regulator_disable (fbi->reg_lcd); +if (ret) +dev_err (&fbi->pdev->dev, +"lcd regulator disable failed with error: %d\n" , + ret); + } }static int imxfb_blank (int blank,struct fb_info *info)
@@ -1020,6 +1043,10 @@ static int imxfb_probe(struct platform_device *pdev) goto failed_register; } + fbi->reg_lcd =devm_regulator_get (&pdev->dev,"lcd" ); +if (IS_ERR (fbi->reg_lcd)) + fbi->reg_lcd =NULL ; +imxfb_enable_controller (fbi); fbi->pdev = pdev;#ifdef PWMR_BACKLIGHT_AVAILABLE
Signature · 1 line
1.7.9.5
PATCH 2/11 video: imxfb: Introduce regulator support.
Quoted 84 lines · Denis Carikli
This commit is based on the following commit by Fabio Estevam:
4344429 video: mxsfb: Introduce regulator supportCc Fabio Estevam <[email protected]>Cc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Jean-Christophe Plagniol-Villard <[email protected]>Cc Tomi Valkeinen <[email protected]>Cc linux-fbdev at vger.kernel.orgCc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>--- drivers/video/imxfb.c | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)drivers/video/imxfb.c +23
-0@@ -28,6 +28,7 @@#include <linux/cpufreq.h> #include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/regulator/consumer.h> #include <linux/dma-mapping.h> #include <linux/io.h> #include <linux/math64.h> @@ -145,6 +146,7 @@ struct imxfb_info {struct clk *clk_ipg;struct clk *clk_ahb;struct clk *clk_per; +struct regulator *reg_lcd;enum imxfb_type devtype;bool enabled;@@ -563,12 +565,23 @@ static void imxfb_exit_backlight(struct imxfb_info *fbi)static void imxfb_enable_controller (struct imxfb_info *fbi) { +int ret;if (fbi->enabled)return ;pr_debug ("Enabling LCD controller\n" ); +if (fbi->reg_lcd) { + ret =regulator_enable (fbi->reg_lcd); +if (ret) { +dev_err (&fbi->pdev->dev, +"lcd regulator enable failed with error: %d\n" , + ret); +return ; + } + } +writel (fbi->screen_dma, fbi->regs +LCDC_SSA );/* panning offset 0 (0 pixel offset) */ @@ -597,6 +610,8 @@ static void imxfb_enable_controller(struct imxfb_info *fbi)static void imxfb_disable_controller (struct imxfb_info *fbi) { +int ret; +if (!fbi->enabled)return ;@@ -613,6 +628,14 @@ static void imxfb_disable_controller(struct imxfb_info *fbi) fbi->enabled = false;writel (0 , fbi->regs +LCDC_RMCR ); + +if (fbi->reg_lcd) { + ret =regulator_disable (fbi->reg_lcd); +if (ret) +dev_err (&fbi->pdev->dev, +"lcd regulator disable failed with error: %d\n" , + ret); + } }static int imxfb_blank (int blank,struct fb_info *info)
drivers/video/imxfb.c static int imxfb_probe(struct platform_device *pdev) · line 1046
Quoted 4 lines
drivers/video/imxfb.c +1
-0@@ -1020,6 +1043,10 @@ static int imxfb_probe(struct platform_device *pdev) goto failed_register; } + fbi->reg_lcd =devm_regulator_get (&pdev->dev,"lcd" );
put a warning at list
otherwise looks ok
Best Regards,
J.
Quoted 9 lines
drivers/video/imxfb.c +3
-0+if (IS_ERR (fbi->reg_lcd)) + fbi->reg_lcd =NULL ; +imxfb_enable_controller (fbi); fbi->pdev = pdev;#ifdef PWMR_BACKLIGHT_AVAILABLE Signature · 1 line
1.7.9.5
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
---
ChangeLog v3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.
- def_value int becomes an u32.
- gbl->def_value was set to pdata->def_value in pdata mode to avoid an extra check.
--- .../bindings/video/backlight/gpio-backlight.txt | 20 ++++++ drivers/video/backlight/gpio_backlight.c | 69 ++++++++++++++++++-- 2 files changed, 82 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +20 -0
@@ -0,0 +1,20 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight + (see GPIO binding[0] for more details). + +Optional properties: + - default-brightness-level: the default brightness level (can be 0(off) or + 1(on) since GPIOs only support theses levels). + +[0]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 0>; + default-brightness-level = <0>; + };
drivers/video/backlight/gpio_backlight.c +62 -7
121 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Hi Denis,
Thanks for the patch. Please see below for a couple of small comment.
Quoted 46 lines · On Monday 21 October 2013 11:13:33 Denis Carikli wrote:
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set. -def_valueint becomes an u32.
-gbl->def_valuewas set topdata->def_valuein pdata mode to avoid an extra check.--- .../bindings/video/backlight/gpio-backlight.txt | 20 ++++++ drivers/video/backlight/gpio_backlight.c | 69 +++++++++++++++-- 2 files changed, 82 insertions(+), 7 deletions(-) create mode 100644
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtdiff --git
a/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtb/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtnew file mode 100644
index 0000000..3474d4aDocumentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +5
-0@@ -0,0 +1,20 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling thebacklight
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +4
-0+ (see GPIO binding[0] for more details). + +Optional properties: + - default-brightness-level: the default brightness level (can be 0(off)
Quoted 2 lines
or
+ 1(on) since GPIOs only support theses levels).
I believe you should specify what the default value is when the property isn't available.
Quoted 36 lines
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +10
-0+ +[0]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 0>; + default-brightness-level = <0>; + };(quoted diff) +0
-0
b/drivers/video/backlight/gpio_backlight.cindex 81fb127..248124d 100644drivers/video/backlight/gpio_backlight.c +4
-0@@ -13,6 +13,8 @@#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> #include <linux/platform_data/gpio_backlight.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -23,6 +25,7 @@ struct gpio_backlight {int gpio;int active; +u32 def_value; };static int gpio_backlight_update_status (struct backlight_device *bl)@@ -60,6 +63,41 @@ static const struct backlight_ops gpio_backlight_ops = { .check_fb = gpio_backlight_check_fb, }; +static int gpio_backlight_probe_dt(struct platform_device *pdev,
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 76
Quoted 10 lines
drivers/video/backlight/gpio_backlight.c +10
-0+ struct gpio_backlight *gbl) +{ +struct device_node *np = pdev->dev.of_node; +enum of_gpio_flags gpio_flags; +int ret; + + gbl->fbdev =NULL ; + gbl->gpio =of_get_gpio_flags (np,0 , &gpio_flags); + + gbl->active = (gpio_flags &OF_GPIO_ACTIVE_LOW ) ?0 :1 ;
I would move this line after the error check below.
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 79
Quoted 3 lines
drivers/video/backlight/gpio_backlight.c +3
-0+ +if (gbl->gpio == -EPROBE_DEFER ) { +return ERR_PTR (-EPROBE_DEFER );
Any reason not to retrun -EPROBE_DEFER directly ?
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 83
Quoted 4 lines
drivers/video/backlight/gpio_backlight.c +4
-0+ }else if (gbl->gpio <0 ) { +dev_err (&pdev->dev,"Error: gpios is a required parameter.\n" ); +return gbl->gpio; + }
Maybe you would do something like
if (gbl->gpio < 0) {
if (gbl->gpio == -EPROBE_DEFER)
dev_err(&pdev->dev, "Error: gpios is a required parameter.\n");
return gbl->gpio;
}drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = {
Quoted 11 lines
drivers/video/backlight/gpio_backlight.c +11
-0+ + ret =of_property_read_u32 (np,"default-brightness-level" , + &gbl->def_value); +if (ret <0 ) { +/* The property is optional. */ + gbl->def_value =1 ; + } + +if (gbl->def_value >1 ) { + dev_warn(&pdev->dev, + "Warning: Invalid default-brightness-level value. Its value can
be
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 95
Quoted 1 line
drivers/video/backlight/gpio_backlight.c +0
-0either 0(off) or 1(on).\n");
I believe a less verbose message (without the second sentence) would have done, but that's up to you.
Quoted 79 lines
drivers/video/backlight/gpio_backlight.c +6
-0+ gbl->def_value =1 ; + } + +return 0 ; +} +static int gpio_backlight_probe (struct platform_device *pdev) {drivers/video/backlight/gpio_backlight.c +16
-6struct gpio_backlight_platform_data *pdata =@@ -67,10 +105,12 @@ static int gpio_backlight_probe(struct platform_device *pdev) struct backlight_properties props;struct backlight_device *bl;struct gpio_backlight *gbl; +struct device_node *np = pdev->dev.of_node;int ret; -if (!pdata) { -dev_err (&pdev->dev,"failed to find platform data\n" ); +if (!pdata && !np) { +dev_err (&pdev->dev, +"failed to find platform data or device tree node.\n" );return -ENODEV ; }@@ -79,14 +119,22 @@ static int gpio_backlight_probe(struct platform_device *pdev) return -ENOMEM; gbl->dev = &pdev->dev; - gbl->fbdev = pdata->fbdev; - gbl->gpio = pdata->gpio; - gbl->active = pdata->active_low ?0 :1 ; + +if (np) { + ret =gpio_backlight_probe_dt (pdev, gbl); +if (ret) +return ret; + }else { + gbl->fbdev = pdata->fbdev; + gbl->gpio = pdata->gpio; + gbl->active = pdata->active_low ?0 :1 ; + gbl->def_value = pdata->def_value; + } ret =devm_gpio_request_one (gbl->dev, gbl->gpio,GPIOF_DIR_OUT | (gbl->active ?GPIOF_INIT_LOW :GPIOF_INIT_HIGH ), - pdata->name); + pdata ? pdata->name :"backlight" );if (ret <0 ) {drivers/video/backlight/gpio_backlight.c +8
-1dev_err (&pdev->dev,"unable to request GPIO\n" );return ret;@@ -103,17 +151,24 @@ static int gpio_backlight_probe(struct platform_device *pdev) return PTR_ERR(bl); } - bl->props.brightness = pdata->def_value; + bl->props.brightness = gbl->def_value; +backlight_update_status (bl);platform_set_drvdata (pdev, bl);return 0 ; } +static struct of_device_id gpio_backlight_of_match[] = { + { .compatible ="gpio-backlight" }, + {/* sentinel */ } +}; +static struct platform_driver gpio_backlight_driver = { .driver = { .name ="gpio-backlight" , .owner =THIS_MODULE , + .of_match_table =of_match_ptr (gpio_backlight_of_match), }, .probe = gpio_backlight_probe, };
Signature · 3 lines
Regards, Laurent Pinchart
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 119 lines · Laurent Pinchart
Hi Denis,
Thanks for the patch. Please see below for a couple of small comment.
Quoted 46 lines · On Monday 21 October 2013 11:13:33 Denis Carikli wrote:
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set. -def_valueint becomes an u32.
-gbl->def_valuewas set topdata->def_valuein pdata mode to avoid an extra check.--- .../bindings/video/backlight/gpio-backlight.txt | 20 ++++++ drivers/video/backlight/gpio_backlight.c | 69 +++++++++++++++-- 2 files changed, 82 insertions(+), 7 deletions(-) create mode 100644
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtdiff --git
a/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtb/Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtnew file mode 100644
index 0000000..3474d4aDocumentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +5
-0@@ -0,0 +1,20 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling thebacklight
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +4
-0+ (see GPIO binding[0] for more details). + +Optional properties: + - default-brightness-level: the default brightness level (can be 0(off)Quoted 2 lines
or
+ 1(on) since GPIOs only support theses levels).I believe you should specify what the default value is when the property isn't available.
Quoted 36 lines
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +10
-0+ +[0]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 0>; + default-brightness-level = <0>; + };(quoted diff) +0
-0
b/drivers/video/backlight/gpio_backlight.cindex 81fb127..248124d 100644drivers/video/backlight/gpio_backlight.c +4
-0@@ -13,6 +13,8 @@#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> #include <linux/platform_data/gpio_backlight.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -23,6 +25,7 @@ struct gpio_backlight {int gpio;int active; +u32 def_value; };static int gpio_backlight_update_status (struct backlight_device *bl)@@ -60,6 +63,41 @@ static const struct backlight_ops gpio_backlight_ops = { .check_fb = gpio_backlight_check_fb, }; +static int gpio_backlight_probe_dt(struct platform_device *pdev,drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 76
Quoted 10 lines
drivers/video/backlight/gpio_backlight.c +10
-0+ struct gpio_backlight *gbl) +{ +struct device_node *np = pdev->dev.of_node; +enum of_gpio_flags gpio_flags; +int ret; + + gbl->fbdev =NULL ; + gbl->gpio =of_get_gpio_flags (np,0 , &gpio_flags); + + gbl->active = (gpio_flags &OF_GPIO_ACTIVE_LOW ) ?0 :1 ;I would move this line after the error check below.
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 79
Quoted 3 lines
drivers/video/backlight/gpio_backlight.c +3
-0+ +if (gbl->gpio == -EPROBE_DEFER ) { +return ERR_PTR (-EPROBE_DEFER );Any reason not to retrun -EPROBE_DEFER directly ?
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 83
Quoted 4 lines
drivers/video/backlight/gpio_backlight.c +4
-0+ }else if (gbl->gpio <0 ) { +dev_err (&pdev->dev,"Error: gpios is a required parameter.\n" ); +return gbl->gpio; + }Maybe you would do something like
Quoted 3 lines
if (gbl->gpio < 0) {
if (gbl->gpio == -EPROBE_DEFER)
dev_err(&pdev->dev, "Error: gpios is a required parameter.\n");it's not an error it's that the gpio driver is not yet probed
so it's need to be !=
Quoted 15 lines
return gbl->gpio; }drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = {
Quoted 11 lines
drivers/video/backlight/gpio_backlight.c +11
-0+ + ret =of_property_read_u32 (np,"default-brightness-level" , + &gbl->def_value); +if (ret <0 ) { +/* The property is optional. */ + gbl->def_value =1 ; + } + +if (gbl->def_value >1 ) { + dev_warn(&pdev->dev, + "Warning: Invalid default-brightness-level value. Its value canbe
Quoted 4 lines
drivers/video/backlight/gpio_backlight.c static const struct backlight_ops gpio_backlight_ops = { · line 95
Quoted 1 line
drivers/video/backlight/gpio_backlight.c +0
-0either 0(off) or 1(on).\n");I believe a less verbose message (without the second sentence) would have done, but that's up to you.
as it's only 0 or 1 why not just use a boolean
Quoted 85 lines
Quoted 80 lines
drivers/video/backlight/gpio_backlight.c +6
-0+ gbl->def_value =1 ; + } + +return 0 ; +} +static int gpio_backlight_probe (struct platform_device *pdev) {drivers/video/backlight/gpio_backlight.c +16
-6struct gpio_backlight_platform_data *pdata =@@ -67,10 +105,12 @@ static int gpio_backlight_probe(struct platform_device *pdev) struct backlight_properties props;struct backlight_device *bl;struct gpio_backlight *gbl; +struct device_node *np = pdev->dev.of_node;int ret; -if (!pdata) { -dev_err (&pdev->dev,"failed to find platform data\n" ); +if (!pdata && !np) { +dev_err (&pdev->dev, +"failed to find platform data or device tree node.\n" );return -ENODEV ; }@@ -79,14 +119,22 @@ static int gpio_backlight_probe(struct platform_device *pdev) return -ENOMEM; gbl->dev = &pdev->dev; - gbl->fbdev = pdata->fbdev; - gbl->gpio = pdata->gpio; - gbl->active = pdata->active_low ?0 :1 ; + +if (np) { + ret =gpio_backlight_probe_dt (pdev, gbl); +if (ret) +return ret; + }else { + gbl->fbdev = pdata->fbdev; + gbl->gpio = pdata->gpio; + gbl->active = pdata->active_low ?0 :1 ; + gbl->def_value = pdata->def_value; + } ret =devm_gpio_request_one (gbl->dev, gbl->gpio,GPIOF_DIR_OUT | (gbl->active ?GPIOF_INIT_LOW :GPIOF_INIT_HIGH ), - pdata->name); + pdata ? pdata->name :"backlight" );if (ret <0 ) {drivers/video/backlight/gpio_backlight.c +8
-1dev_err (&pdev->dev,"unable to request GPIO\n" );return ret;@@ -103,17 +151,24 @@ static int gpio_backlight_probe(struct platform_device *pdev) return PTR_ERR(bl); } - bl->props.brightness = pdata->def_value; + bl->props.brightness = gbl->def_value; +backlight_update_status (bl);platform_set_drvdata (pdev, bl);return 0 ; } +static struct of_device_id gpio_backlight_of_match[] = { + { .compatible ="gpio-backlight" }, + {/* sentinel */ } +}; +static struct platform_driver gpio_backlight_driver = { .driver = { .name ="gpio-backlight" , .owner =THIS_MODULE , + .of_match_table =of_match_ptr (gpio_backlight_of_match), }, .probe = gpio_backlight_probe, };Signature · 3 lines
Regards, Laurent Pinchart
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
In reply to Denis CarikliQuoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>
Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Best Regards,
J.
Quoted 169 lines
-
def_valueint becomes an u32.
-gbl->def_valuewas set topdata->def_valuein pdata mode to avoid an extra check.--- .../bindings/video/backlight/gpio-backlight.txt | 20 ++++++ drivers/video/backlight/gpio_backlight.c | 69 ++++++++++++++++++-- 2 files changed, 82 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtDocumentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +20
-0@@ -0,0 +1,20 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight + (see GPIO binding[0] for more details). + +Optional properties: + - default-brightness-level: the default brightness level (can be 0(off) or + 1(on) since GPIOs only support theses levels). + +[0]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 0>; + default-brightness-level = <0>; + };drivers/video/backlight/gpio_backlight.c +62
-7@@ -13,6 +13,8 @@#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> #include <linux/platform_data/gpio_backlight.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -23,6 +25,7 @@ struct gpio_backlight {int gpio;int active; +u32 def_value; };static int gpio_backlight_update_status (struct backlight_device *bl)@@ -60,6 +63,41 @@ static const struct backlight_ops gpio_backlight_ops = { .check_fb = gpio_backlight_check_fb, }; +static int gpio_backlight_probe_dt (struct platform_device *pdev, +struct gpio_backlight *gbl) +{ +struct device_node *np = pdev->dev.of_node; +enum of_gpio_flags gpio_flags; +int ret; + + gbl->fbdev =NULL ; + gbl->gpio =of_get_gpio_flags (np,0 , &gpio_flags); + + gbl->active = (gpio_flags &OF_GPIO_ACTIVE_LOW ) ?0 :1 ; + +if (gbl->gpio == -EPROBE_DEFER ) { +return ERR_PTR (-EPROBE_DEFER ); + }else if (gbl->gpio <0 ) { +dev_err (&pdev->dev,"Error: gpios is a required parameter.\n" ); +return gbl->gpio; + } + + ret =of_property_read_u32 (np,"default-brightness-level" , + &gbl->def_value); +if (ret <0 ) { +/* The property is optional. */ + gbl->def_value =1 ; + } + +if (gbl->def_value >1 ) { +dev_warn (&pdev->dev, +"Warning: Invalid default-brightness-level value. Its value can be either 0(off) or 1(on).\n" ); + gbl->def_value =1 ; + } + +return 0 ; +} +static int gpio_backlight_probe (struct platform_device *pdev) { struct gpio_backlight_platform_data *pdata =@@ -67,10 +105,12 @@ static int gpio_backlight_probe(struct platform_device *pdev)struct backlight_properties props;struct backlight_device *bl;struct gpio_backlight *gbl; +struct device_node *np = pdev->dev.of_node;int ret; -if (!pdata) { -dev_err (&pdev->dev,"failed to find platform data\n" ); +if (!pdata && !np) { +dev_err (&pdev->dev, +"failed to find platform data or device tree node.\n" );return -ENODEV ; }@@ -79,14 +119,22 @@ static int gpio_backlight_probe(struct platform_device *pdev)return -ENOMEM ; gbl->dev = &pdev->dev; - gbl->fbdev = pdata->fbdev; - gbl->gpio = pdata->gpio; - gbl->active = pdata->active_low ?0 :1 ; + +if (np) { + ret =gpio_backlight_probe_dt (pdev, gbl); +if (ret) +return ret; + }else { + gbl->fbdev = pdata->fbdev; + gbl->gpio = pdata->gpio; + gbl->active = pdata->active_low ?0 :1 ; + gbl->def_value = pdata->def_value; + } ret =devm_gpio_request_one (gbl->dev, gbl->gpio,GPIOF_DIR_OUT | (gbl->active ?GPIOF_INIT_LOW :GPIOF_INIT_HIGH ), - pdata->name); + pdata ? pdata->name :"backlight" );if (ret <0 ) {dev_err (&pdev->dev,"unable to request GPIO\n" );return ret;@@ -103,17 +151,24 @@ static int gpio_backlight_probe(struct platform_device *pdev)return PTR_ERR (bl); } - bl->props.brightness = pdata->def_value; + bl->props.brightness = gbl->def_value; +backlight_update_status (bl);platform_set_drvdata (pdev, bl);return 0 ; } +static struct of_device_id gpio_backlight_of_match[] = { + { .compatible ="gpio-backlight" }, + {/* sentinel */ } +}; +static struct platform_driver gpio_backlight_driver = { .driver = { .name ="gpio-backlight" , .owner =THIS_MODULE , + .of_match_table =of_match_ptr (gpio_backlight_of_match), }, .probe = gpio_backlight_probe, };Signature · 1 line
1.7.9.5
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.
Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
In my opinion every backlight should be hooked up to a display panel, and the display panel driver should be the one responsible for turning the backlight on or off. That's the only way we can guarantee that the backlight is turned on at the right moment so that glitches can be avoided.
One possible migration path would be to update all display panel drivers to cope with an associated backlight device, but even if somebody would even find the time to write the code to do that, I can imagine that we'd have a hard time getting this tested since a lot of the boards that rely on these backlight drivers are legacy and probably no longer very actively used.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131022/48b53d2c/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 25 lines · Thierry Reding
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Quoted 8 lines
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
For me this should not even be a property but handled by the driver them selves in C.
Best Regards,
J.
Quoted 15 lines
In my opinion every backlight should be hooked up to a display panel, and the display panel driver should be the one responsible for turning the backlight on or off. That's the only way we can guarantee that the backlight is turned on at the right moment so that glitches can be avoided.
One possible migration path would be to update all display panel drivers to cope with an associated backlight device, but even if somebody would even find the time to write the code to do that, I can imagine that we'd have a hard time getting this tested since a lot of the boards that rely on these backlight drivers are legacy and probably no longer very actively used.
Thierry
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 35 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 25 lines · Thierry Reding
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Quoted 8 lines
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
Quoted 3 lines
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
I agree that would be preferable, but I don't know of any way to detect what value the bootloader set a GPIO to. The GPIO API requires that you call gpio_direction_output(), and that requires a value parameter which will be used as the output level of the GPIO.
Quoted 2 lines
For me this should not even be a property but handled by the driver them selves in C.
Agreed. There has been some discussion recently about whether devicetree should be extended (or supplemented) to allow defining behaviour as well (in addition to just hardware). But that's not immediately relevant here at this time.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131022/60b1153e/attachment-0001.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 36 lines · Thierry Reding
Quoted 35 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 33 lines · Thierry Reding
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
Quoted 7 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
This is a matter of C code not DT
Quoted 4 lines
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
so handle it in C not in DT
For me the only value a default-brightness would be with a pwn or a ragned value but not on 0-1 for on vs off
Quoted 9 lines
Quoted 4 lines
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
I agree that would be preferable, but I don't know of any way to detect what value the bootloader set a GPIO to. The GPIO API requires that you call
gpio_direction_output(), and that requires a value parameter which will be used as the output level of the GPIO.
For me gpio_get_value can return the value of a an output gpio but this need to be checked with LinusW
Quoted 8 lines
Quoted 3 lines
For me this should not even be a property but handled by the driver them selves in C.
Agreed. There has been some discussion recently about whether devicetree should be extended (or supplemented) to allow defining behaviour as well (in addition to just hardware). But that's not immediately relevant here at this time.
yes
to conclued NACK on the default-brightness here
Best Regards,
J.
Quoted 2 lines
Thierry
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
On 10/23/2013 02:42 PM, Jean-Christophe PLAGNIOL-VILLARD wrote:
...
Quoted 2 lines
For me
gpio_get_valuecan return the value of a an output gpio but this need to be checked with LinusW
That's certainly not true for all possible GPIO controllers; there are at least some that can't read either:
* The value of the physical wire, if the GPIO is configured as an output.
* The value that the GPIO controller is driving as an output.
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 11 lines · Stephen Warren
On 10/23/2013 02:42 PM, Jean-Christophe PLAGNIOL-VILLARD wrote:
...Quoted 2 lines
For me
gpio_get_valuecan return the value of a an output gpio but this need to be checked with LinusWThat's certainly not true for all possible GPIO controllers; there are at least some that can't read either:
* The value of the physical wire, if the GPIO is configured as an output.
* The value that the GPIO controller is driving as an output.
My point originally was that since it's an output pin, you need to configure it as an output before you can use it. The way to do that in Linux is to call gpio_direction_output(). But that will automatically also force the output value to whatever you specify as the second parameter.
I suppose that could be remedied by adding a separate function that doesn't set the value, but as Stephen points out, reading the value of an output pin may not be supported on all hardware.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131023/87631e74/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
In reply to Thierry RedingQuoted 2 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 22 lines · Stephen Warren
Quoted 2 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
That said, it is true that the number of DT users of the pwm-backlight driver is smaller than the number of board file users, and it is much more likely that people are still actively using them, so if we can get everyone to agree on changing the default behaviour that might still be possible.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131023/e82b24c0/attachment-0001.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Hi Thierry,
Quoted 32 lines · On Wednesday 23 October 2013 22:20:12 Thierry Reding wrote:
Quoted 24 lines · Stephen Warren
Quoted 3 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe
PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
Quoted 8 lines
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
I would very much welcome a refactoring of the backlight code that would remove the fbdev dependency and hook backlights to panel drivers. That's something I wanted to work on myself, but that I pushed back after CDF :-)
Quoted 5 lines
That said, it is true that the number of DT users of the pwm-backlight driver is smaller than the number of board file users, and it is much more likely that people are still actively using them, so if we can get everyone to agree on changing the default behaviour that might still be possible.
Signature · 10 lines
Regards, Laurent Pinchart -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 490 bytes Desc: This is a digitally signed message part. URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131024/8e3814bf/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 39 lines · Laurent Pinchart
Hi Thierry,
Quoted 36 lines · On Wednesday 23 October 2013 22:20:12 Thierry Reding wrote:
Quoted 24 lines · Stephen Warren
Quoted 3 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe
PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
Quoted 8 lines
Quoted 4 lines
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
I would very much welcome a refactoring of the backlight code that would remove the fbdev dependency and hook backlights to panel drivers. That's something I wanted to work on myself, but that I pushed back after CDF :-)
Yeah, that would certainly be very welcome. But it's also a pretty daunting job since there are a whole lot of devices out there that aren't easy to test because, well, they're pretty old and chances are that nobody that actually has one is around.
But I guess that we can always try to solve it on a best effort basis, though. Perhaps things can even be done in a backwards-compatible way. I'm thinking for instance that we could introduce a new property, say .enable, but keep any of the others suhc as state, power, fb_blank for backwards-compatibility. Perhaps even emulate them for a while until we've gone and cleaned up all users.
Or is there still a reason to have more than a single bit for backlight state? I don't know any hardware that actually makes a difference between FB_BLANK_NORMAL, FB_BLANK_VSYNC_SUSPEND, FB_BLANK_HSYNC_SUSPEND or FB_BLANK_POWERDOWN. Many drivers in drivers/video seem to be using those, but for backlights I can see no use other than FB_BLANK_UNBLANK meaning enabled and anything else meaning disabled.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131024/1814f327/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Hi Thierry,
Quoted 52 lines · On Thursday 24 October 2013 13:05:25 Thierry Reding wrote:
Quoted 37 lines · Laurent Pinchart
Quoted 36 lines · On Wednesday 23 October 2013 22:20:12 Thierry Reding wrote:
Quoted 24 lines · Stephen Warren
Quoted 3 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe
PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
Quoted 8 lines
Quoted 4 lines
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
I would very much welcome a refactoring of the backlight code that would remove the fbdev dependency and hook backlights to panel drivers. That's something I wanted to work on myself, but that I pushed back after CDF :-)
Yeah, that would certainly be very welcome. But it's also a pretty daunting job since there are a whole lot of devices out there that aren't easy to test because, well, they're pretty old and chances are that nobody that actually has one is around.
Quoted 6 lines
But I guess that we can always try to solve it on a best effort basis, though. Perhaps things can even be done in a backwards-compatible way. I'm thinking for instance that we could introduce a new property, say .enable, but keep any of the others suhc as state, power,
fb_blankfor backwards-compatibility. Perhaps even emulate them for a while until we've gone and cleaned up all users.
That would work with me. I don't think we need more than a best effort approach to porting existing backlight drivers to the new model. When it comes to compatibility with the current interface, I'd like to move the compatibility code to the core instead of leaving it in the individual drivers if possible.
Quoted 6 lines
Or is there still a reason to have more than a single bit for backlight state? I don't know any hardware that actually makes a difference between
FB_BLANK_NORMAL,FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDorFB_BLANK_POWERDOWN. Many drivers indrivers/videoseem to be using those, but for backlights I can see no use other thanFB_BLANK_UNBLANKmeaning enabled and anything else meaning disabled.
I see no use case for the fine-grained state in backlights at the moment.
Signature · 10 lines
Regards, Laurent Pinchart -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 490 bytes Desc: This is a digitally signed message part. URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131025/98b4309b/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 60 lines · Laurent Pinchart
Quoted 52 lines · On Thursday 24 October 2013 13:05:25 Thierry Reding wrote:
Quoted 37 lines · Laurent Pinchart
Quoted 36 lines · On Wednesday 23 October 2013 22:20:12 Thierry Reding wrote:
Quoted 24 lines · Stephen Warren
Quoted 3 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe
PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
Quoted 8 lines
Quoted 4 lines
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
I would very much welcome a refactoring of the backlight code that would remove the fbdev dependency and hook backlights to panel drivers. That's something I wanted to work on myself, but that I pushed back after CDF :-)
Yeah, that would certainly be very welcome. But it's also a pretty daunting job since there are a whole lot of devices out there that aren't easy to test because, well, they're pretty old and chances are that nobody that actually has one is around.
Quoted 6 lines
But I guess that we can always try to solve it on a best effort basis, though. Perhaps things can even be done in a backwards-compatible way. I'm thinking for instance that we could introduce a new property, say .enable, but keep any of the others suhc as state, power,
fb_blankfor backwards-compatibility. Perhaps even emulate them for a while until we've gone and cleaned up all users.
Quoted 5 lines
That would work with me. I don't think we need more than a best effort approach to porting existing backlight drivers to the new model. When it comes to compatibility with the current interface, I'd like to move the compatibility code to the core instead of leaving it in the individual drivers if possible.
I agree with you.
Moving the compatibility code to the core from the individual drivers looks good. :-)
Quoted 5 lines
Quoted 5 lines
Or is there still a reason to have more than a single bit for backlight state? I don't know any hardware that actually makes a difference between
FB_BLANK_NORMAL,FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDorFB_BLANK_POWERDOWN.
On Exynos side, I have never seen that FB_BLANK_VSYNC_SUSPEND, FB_BLANK_HSYNC_SUSPEND are used for controlling display panels or Display controllers.
However, I heard that FB_BLANK_VSYNC_SUSPEND, FB_BLANK_HSYNC_SUSPEND are used for some monitors.
Best regards,
Jingoo Han
Quoted 5 lines
Quoted 3 lines
Many drivers in
drivers/videoseem to be using
those, but for backlights I can see no use other thanFB_BLANK_UNBLANKmeaning enabled and anything else meaning disabled.I see no use case for the fine-grained state in backlights at the moment.
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 77 lines · Jingoo Han
Quoted 60 lines · Laurent Pinchart
Quoted 52 lines · On Thursday 24 October 2013 13:05:25 Thierry Reding wrote:
Quoted 37 lines · Laurent Pinchart
Quoted 36 lines · On Wednesday 23 October 2013 22:20:12 Thierry Reding wrote:
Quoted 24 lines · Stephen Warren
Quoted 3 lines · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe
PLAGNIOL-VILLARD wrote:
...
Quoted 11 lines
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
It may well be reasonable to change the default behaviour for devices instantiated from DT. If it's not possible to instantiate the device from DT yet, then it's not possible for anyone to be relying on the default behaviour yet, since there is none. So, perhaps the default could be:
Quoted 6 lines
* If device instantiated from a board file, default to on, for backwards-compatibility.
* If device instantiated from DT, there is no backwards compatibility to be concerned with, since this is a new feature, hence default to off, since we think that's the correct thing to do.
I actually had a patch to do precisely that. However I then realized that people have actually been using pwm-backlight in DT for a while already and therefore may be relying on that behaviour as well.
Quoted 8 lines
Quoted 4 lines
It also isn't really an issue of DT vs. non-DT. The simple fact is that besides the backlight driver there's usually no other code that enables a backlight on boot. The only way to do so that I know of is using the DRM panel patches that I've been working on.
I would very much welcome a refactoring of the backlight code that would remove the fbdev dependency and hook backlights to panel drivers. That's something I wanted to work on myself, but that I pushed back after CDF :-)
Yeah, that would certainly be very welcome. But it's also a pretty daunting job since there are a whole lot of devices out there that aren't easy to test because, well, they're pretty old and chances are that nobody that actually has one is around.
Quoted 6 lines
But I guess that we can always try to solve it on a best effort basis, though. Perhaps things can even be done in a backwards-compatible way. I'm thinking for instance that we could introduce a new property, say .enable, but keep any of the others suhc as state, power,
fb_blankfor backwards-compatibility. Perhaps even emulate them for a while until we've gone and cleaned up all users.Quoted 5 lines
That would work with me. I don't think we need more than a best effort approach to porting existing backlight drivers to the new model. When it comes to compatibility with the current interface, I'd like to move the compatibility code to the core instead of leaving it in the individual drivers if possible.
I agree with you.
Moving the compatibility code to the core from the individual drivers looks good. :-)Quoted 5 lines
Quoted 5 lines
Or is there still a reason to have more than a single bit for backlight state? I don't know any hardware that actually makes a difference between
FB_BLANK_NORMAL,FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDorFB_BLANK_POWERDOWN.
Quoted 6 lines
On Exynos side, I have never seen that
FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDare used for controlling display panels or Display controllers.However, I heard that
FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDare used for some monitors.
I think that those may make sense in the context of fbdev, and looking at some fbdev drivers seems to substantiate that.
However, I don't think backlights have any such capability. I mean they are either on or off, right? There's no such thing as partially off, or partially on. How would a backlight behave differently if the panel was in HSYNC suspend mode or VSYNC suspend mode?
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131101/0e603e9b/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 3 lines · Thierry Reding
Quoted 2 lines · Jingoo Han
Quoted 1 line · Laurent Pinchart
On Thursday 24 October 2013 13:05:25 Thierry Reding wrote:
[....]
Quoted 12 lines
Quoted 11 lines
Quoted 4 lines
Quoted 4 lines
Or is there still a reason to have more than a single bit for backlight state? I don't know any hardware that actually makes a difference between
FB_BLANK_NORMAL,FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDorFB_BLANK_POWERDOWN.On Exynos side, I have never seen that
FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDare used for controlling display panels or Display controllers.However, I heard that
FB_BLANK_VSYNC_SUSPEND,FB_BLANK_HSYNC_SUSPENDare used for some monitors.
Quoted 7 lines
I think that those may make sense in the context of fbdev, and looking at some fbdev drivers seems to substantiate that.
However, I don't think backlights have any such capability. I mean they are either on or off, right? There's no such thing as partially off, or partially on. How would a backlight behave differently if the panel was in HSYNC suspend mode or VSYNC suspend mode?
Hi Thierry Reding.
I agree with you.
In the case of backlight, there is no need that a backlight behaves differently in HSYNC suspend mode or VSYNC suspend mode.
Best regards,
Jingoo Han
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
In reply to Thierry RedingQuoted 39 lines · Thierry Reding
Quoted 35 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 25 lines · Thierry Reding
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Quoted 8 lines
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
Quoted 8 lines
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
I agree with your opinion.
But, I can't decide how to change it.
Quoted 9 lines
Quoted 4 lines
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
I agree that would be preferable, but I don't know of any way to detect what value the bootloader set a GPIO to. The GPIO API requires that you call
gpio_direction_output(), and that requires a value parameter which will be used as the output level of the GPIO.
Jean-Christophe's point is right.
We may need to discuss 'the way to detect what value the bootloader set a GPIO to'.
Quoted 7 lines
Quoted 2 lines
For me this should not even be a property but handled by the driver them selves in C.
Agreed. There has been some discussion recently about whether devicetree should be extended (or supplemented) to allow defining behaviour as well (in addition to just hardware). But that's not immediately relevant here at this time.
Agreed.
Best regards,
Jingoo Han
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Quoted 45 lines · Jingoo Han
Quoted 44 lines · Thierry Reding
Quoted 35 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 25 lines · Thierry Reding
Quoted 19 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 15 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 3 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Quoted 8 lines
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
Quoted 6 lines
Quoted 3 lines
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
I agree with your opinion.
But, I can't decide how to change it.
One solution that Stephen proposed was to make all DT-based setups use a new default (off). An advantage of that is that such setups are still fairly actively being worked on, so we can probably get early adopters to cope with the new default.
Looking through some DTS files it seems that many use the pwm-backlight driver. So if we can get some concensus from all the users that changing the default would be okay, then I think we could reasonably change it.
Another solution perhaps would be to add a property to DT which encodes the default state of the backlight on boot. This used to be impossible because the general concensus was that DT should describe hardware only and not software policy. During the kernel summit this requirement was somewhat relaxed and it should now be okay to describe system configuration data, and I think this would be a good match. If the system is designed to keep the backlight off by default because some other component (display panel driver) is meant to turn it on later, that's system configuration data, right?
Perhaps a boolean property could be used:
backlight {
compatible = "pwm-backlight";
...
backlight-default-off;
};Quoted 9 lines
Quoted 8 lines
Quoted 3 lines
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
I agree that would be preferable, but I don't know of any way to detect what value the bootloader set a GPIO to. The GPIO API requires that you call
gpio_direction_output(), and that requires a value parameter which will be used as the output level of the GPIO.
Quoted 4 lines
Jean-Christophe's point is right.
We may need to discuss 'the way to detect what value the bootloader set a GPIO to'.
Since some GPIO hardware simply can't do it, I guess we could resolve to passing such information via DT. That obviously won't work for non-DT setups, but I guess that's something we could live with.
One possibility would be to supplement the backlight-default-off property with another property (backlight-boot-on) that can be passed on to the kernel from the bootloader to signal that it has turned the backlight on.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131101/72ee32dc/attachment-0001.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
Hi Thierry,
Quoted 3 lines · On Friday 01 November 2013 11:13:47 Thierry Reding wrote:
Quoted 2 lines · Jingoo Han
Quoted 1 line · Thierry Reding
On Tue, Oct 22, 2013 at 05:34:45PM +0200, Jean-Christophe PLAGNIOL-
Quoted 2 lines · VILLARD
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines · Thierry Reding
Quoted 1 line
On Tue, Oct 22, 2013 at 06:58:33AM +0200, Jean-Christophe PLAGNIOL-
Quoted 88 lines · VILLARD
Quoted 42 lines
Quoted 42 lines
Quoted 34 lines
Quoted 25 lines
Quoted 20 lines · Denis Carikli
Quoted 15 lines
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa?mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B?nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>Quoted 4 lines
---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.> > > > >Quoted 4 lines
by default we set OFF not ON
do not actiate driver or properti by default you can not known to consequence on the hw
Quoted 8 lines
Turning on a backlight by default is what pretty much every backlight driver does. I personally think that's the wrong default, I even tried to get some discussion started recently about how we could change this. However, given that this has been the case for possibly as long as the subsystem has existed, suddenly changing it might cause quite a few of our users to boot the new kernel and not see their display come up. As with any other ABI, this isn't something we can just change without a very good migration path.
Quoted 2 lines
I'm sorry but the blacklight descibe in DT have nothing to do with the common pratice that the current driver have today
That's not at all what I said. What I said was that the majority of backlight drivers currently default to turning the backlight on when probed. Therefore I think it would be consistent if this driver did the same.
Quoted 6 lines
Quoted 3 lines
I also said that I don't think it's a very good default, but at the same time we can't just go and change the default behaviour at will because people may rely on it.
I agree with your opinion.
But, I can't decide how to change it.One solution that Stephen proposed was to make all DT-based setups use a new default (off). An advantage of that is that such setups are still fairly actively being worked on, so we can probably get early adopters to cope with the new default.
Looking through some DTS files it seems that many use the pwm-backlight driver. So if we can get some concensus from all the users that changing the default would be okay, then I think we could reasonably change it.
Another solution perhaps would be to add a property to DT which encodes the default state of the backlight on boot. This used to be impossible because the general concensus was that DT should describe hardware only and not software policy. During the kernel summit this requirement was somewhat relaxed and it should now be okay to describe system configuration data, and I think this would be a good match. If the system is designed to keep the backlight off by default because some other component (display panel driver) is meant to turn it on later, that's system configuration data, right?
Perhaps a boolean property could be used:
backlight { compatible = "pwm-backlight"; ... backlight-default-off; };Quoted 10 lines
Quoted 9 lines
Quoted 4 lines
put on by default if wrong specially without the property define. Even put it on by default it wrong as the bootloader may have set it already for splash screen and to avoid glitch the drivers need to detect this.
I agree that would be preferable, but I don't know of any way to detect what value the bootloader set a GPIO to. The GPIO API requires that you call
gpio_direction_output(), and that requires a value parameter which will be used as the output level of the GPIO.
Quoted 8 lines
Quoted 4 lines
Jean-Christophe's point is right.
We may need to discuss 'the way to detect what value the bootloader set a GPIO to'.
Since some GPIO hardware simply can't do it, I guess we could resolve to passing such information via DT. That obviously won't work for non-DT setups, but I guess that's something we could live with.
For what it's worth, the pcf857x GPIO controllers suffer from this problem, and the solution was to use a DT property to specify the initial GPIOs state. The driver can thus implement gpio_get_value() properly and the hardware limitation is hidden from the clients.
https://lkml.org/lkml/2013/9/21/105
Quoted 3 lines
One possibility would be to supplement the backlight-default-off property with another property (backlight-boot-on) that can be passed on to the kernel from the bootloader to signal that it has turned the backlight on.
Signature · 10 lines
Regards, Laurent Pinchart -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 490 bytes Desc: This is a digitally signed message part. URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131106/83d67344/attachment.sig>
PATCH v4 1/1 video: backlight: gpio-backlight: Add DT support.
In reply to Denis CarikliQuoted 33 lines · Denis Carikli
Cc Richard Purdie <[email protected]>Cc Jingoo Han <[email protected]>Cc Laurent Pinchart <[email protected]>Cc Rob Herring <[email protected]>Cc Pawel Moll <[email protected]>Cc Mark Rutland <[email protected]>Cc Stephen Warren <[email protected]>Cc Ian Campbell <[email protected]>Cc devicetree at vger.kernel.orgCc Sascha Hauer <[email protected]>Cc linux-arm-kernel at lists.infradead.orgCc Lothar Wa??mann <[email protected]>Cc Jean-Christophe Plagniol-Villard <[email protected]>Cc Eric B??nard <[email protected]>Signed-off-by Denis Carikli <[email protected]>---
ChangeLogv3->v4:
- The default-brightness property is now optional, it defaults to 1 if not set.
-def_valueint becomes an u32.
-gbl->def_valuewas set topdata->def_valuein pdata mode to avoid an extra check.--- .../bindings/video/backlight/gpio-backlight.txt | 20 ++++++ drivers/video/backlight/gpio_backlight.c | 69 ++++++++++++++++++-- 2 files changed, 82 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/video/backlight/gpio-backlight.txtDocumentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +0
-0
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt line 10
Quoted 10 lines
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +10
-0@@ -0,0 +1,20 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight + (see GPIO binding[0] for more details). + +Optional properties: + - default-brightness-level: the default brightness level (can be 0(off) or + 1(on) since GPIOs only support theses levels).
Seems odd to call it brightness since it can only be on or off. Why not call it "default-state" or and empty bool named "default-on"?
Otherwise looks okay to me.
g.
Quoted 149 lines
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt new file +10
-0+ +[0]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 0>; + default-brightness-level = <0>; + };drivers/video/backlight/gpio_backlight.c +62
-7@@ -13,6 +13,8 @@#include <linux/init.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> #include <linux/platform_data/gpio_backlight.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -23,6 +25,7 @@ struct gpio_backlight {int gpio;int active; +u32 def_value; };static int gpio_backlight_update_status (struct backlight_device *bl)@@ -60,6 +63,41 @@ static const struct backlight_ops gpio_backlight_ops = { .check_fb = gpio_backlight_check_fb, }; +static int gpio_backlight_probe_dt (struct platform_device *pdev, +struct gpio_backlight *gbl) +{ +struct device_node *np = pdev->dev.of_node; +enum of_gpio_flags gpio_flags; +int ret; + + gbl->fbdev =NULL ; + gbl->gpio =of_get_gpio_flags (np,0 , &gpio_flags); + + gbl->active = (gpio_flags &OF_GPIO_ACTIVE_LOW ) ?0 :1 ; + +if (gbl->gpio == -EPROBE_DEFER ) { +return ERR_PTR (-EPROBE_DEFER ); + }else if (gbl->gpio <0 ) { +dev_err (&pdev->dev,"Error: gpios is a required parameter.\n" ); +return gbl->gpio; + } + + ret =of_property_read_u32 (np,"default-brightness-level" , + &gbl->def_value); +if (ret <0 ) { +/* The property is optional. */ + gbl->def_value =1 ; + } + +if (gbl->def_value >1 ) { +dev_warn (&pdev->dev, +"Warning: Invalid default-brightness-level value. Its value can be either 0(off) or 1(on).\n" ); + gbl->def_value =1 ; + } + +return 0 ; +} +static int gpio_backlight_probe (struct platform_device *pdev) { struct gpio_backlight_platform_data *pdata =@@ -67,10 +105,12 @@ static int gpio_backlight_probe(struct platform_device *pdev)struct backlight_properties props;struct backlight_device *bl;struct gpio_backlight *gbl; +struct device_node *np = pdev->dev.of_node;int ret; -if (!pdata) { -dev_err (&pdev->dev,"failed to find platform data\n" ); +if (!pdata && !np) { +dev_err (&pdev->dev, +"failed to find platform data or device tree node.\n" );return -ENODEV ; }@@ -79,14 +119,22 @@ static int gpio_backlight_probe(struct platform_device *pdev)return -ENOMEM ; gbl->dev = &pdev->dev; - gbl->fbdev = pdata->fbdev; - gbl->gpio = pdata->gpio; - gbl->active = pdata->active_low ?0 :1 ; + +if (np) { + ret =gpio_backlight_probe_dt (pdev, gbl); +if (ret) +return ret; + }else { + gbl->fbdev = pdata->fbdev; + gbl->gpio = pdata->gpio; + gbl->active = pdata->active_low ?0 :1 ; + gbl->def_value = pdata->def_value; + } ret =devm_gpio_request_one (gbl->dev, gbl->gpio,GPIOF_DIR_OUT | (gbl->active ?GPIOF_INIT_LOW :GPIOF_INIT_HIGH ), - pdata->name); + pdata ? pdata->name :"backlight" );if (ret <0 ) {dev_err (&pdev->dev,"unable to request GPIO\n" );return ret;@@ -103,17 +151,24 @@ static int gpio_backlight_probe(struct platform_device *pdev)return PTR_ERR (bl); } - bl->props.brightness = pdata->def_value; + bl->props.brightness = gbl->def_value; +backlight_update_status (bl);platform_set_drvdata (pdev, bl);return 0 ; } +static struct of_device_id gpio_backlight_of_match[] = { + { .compatible ="gpio-backlight" }, + {/* sentinel */ } +}; +static struct platform_driver gpio_backlight_driver = { .driver = { .name ="gpio-backlight" , .owner =THIS_MODULE , + .of_match_table =of_match_ptr (gpio_backlight_of_match), }, .probe = gpio_backlight_probe, };Signature · 7 lines
1.7.9.5 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel