libata-dev-2.6: pdc2027x timing register fix for 100MHz adapters
PATCH 1/1 libata-dev-2.6: pdc2027x timing register fix for 100MHz adapters
Hi Jeff,
I did not get the pdc2027x timing registers right for the 100 MHz adapters.
For the 100MHz adapters, the hardware will automatically set the timing registers to the correct value. No need to set the timing register by software table lookup.
(The values in the lookup table are for 133Mhz adapters, which are incorrect for 100MHz adapters.)
Attached please find the patch against the libata-dev-2.6 tree for your review. Thanks.
Albert
----------------------------------------------------------------------------------------------
drivers/scsi/pata_pdc2027x.c 2005-02-02 16:17:26.000000000 +0800 renamed from drivers/scsi/pata_pdc2027x.c 2005-02-02 16:08:39.000000000 +0800 +29 -4
@@ -29,7 +29,7 @@ #include <asm/io.h> #define DRV_NAME "pata_pdc2027x" -#define DRV_VERSION "0.55" +#define DRV_VERSION "0.56" #undef PDC_DEBUG #ifdef PDC_DEBUG
@@ -130,7 +130,32 @@ .bios_param = ata_std_bios_param, }; -static struct ata_port_operations pdc2027x_pata_ops = { +static struct ata_port_operations pdc2027x_pata100_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = pdc2027x_phy_reset, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, +}; + +static struct ata_port_operations pdc2027x_pata133_ops = { .port_disable = ata_port_disable, .set_piomode = pdc2027x_set_piomode, .set_dmamode = pdc2027x_set_dmamode,
@@ -167,7 +192,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA5, /* udma0-5 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata100_ops, }, /* PDC_UDMA_133 */ {
@@ -177,7 +202,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA6, /* udma0-6 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata133_ops, }, };
drivers/scsi/pata_pdc2027x.c +29 -4
@@ -29,7 +29,7 @@#include <asm/io.h> #define DRV_NAME "pata_pdc2027x" -#define DRV_VERSION "0.55" +#define DRV_VERSION "0.56"#undef PDC_DEBUG#ifdef PDC_DEBUG
@@ -130,7 +130,32 @@ .bios_param = ata_std_bios_param, }; -static struct ata_port_operations pdc2027x_pata_ops = { +static struct ata_port_operations pdc2027x_pata100_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = pdc2027x_phy_reset, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, +}; + +static struct ata_port_operations pdc2027x_pata133_ops = { .port_disable = ata_port_disable, .set_piomode = pdc2027x_set_piomode, .set_dmamode = pdc2027x_set_dmamode,
@@ -167,7 +192,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA5, /* udma0-5 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata100_ops, },/* PDC_UDMA_133 */ {
@@ -177,7 +202,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA6, /* udma0-6 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata133_ops, }, };
Quoted 9 lines
Albert Lee wrote:
I did not get the pdc2027x timing registers right for the 100 MHz adapters.
For the 100MHz adapters, the hardware will automatically set the timing registers to the correct value. No need to set the timing register by software table lookup.
(The values in the lookup table are for 133Mhz adapters, which are incorrect for 100MHz adapters.)Attached please find the patch against the libata-dev-2.6 tree for your review. Thanks.
Jeff,
Please ignore my previous pdc2027x timing registers patch.
Attached please find the resubmitted patch against libata-dev-2.6 tree for your review. Thanks.
Changes:
1. For the 100MHz pdc20268 and pdc20270 adapters, rely on the hardware to set the timing registers.
2. Add the new .bmdma_stop and .bmdma_status to pdc2027x_pata100_ops and pdc2027x_pata133_ops.
Albert
=============================================================================================
drivers/scsi/pata_pdc2027x.c +33 -4
@@ -29,7 +29,7 @@#include <asm/io.h> #define DRV_NAME "pata_pdc2027x" -#define DRV_VERSION "0.55" +#define DRV_VERSION "0.57"#undef PDC_DEBUG#ifdef PDC_DEBUG
@@ -130,7 +130,34 @@ .bios_param = ata_std_bios_param, }; -static struct ata_port_operations pdc2027x_pata_ops = { +static struct ata_port_operations pdc2027x_pata100_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = pdc2027x_phy_reset, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, +}; + +static struct ata_port_operations pdc2027x_pata133_ops = { .port_disable = ata_port_disable, .set_piomode = pdc2027x_set_piomode, .set_dmamode = pdc2027x_set_dmamode,
@@ -147,6 +174,8 @@ .check_atapi_dma = pdc2027x_check_atapi_dma, .bmdma_setup = ata_bmdma_setup, .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, .qc_prep = ata_qc_prep, .qc_issue = ata_qc_issue_prot, .eng_timeout = ata_eng_timeout,
@@ -167,7 +196,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA5, /* udma0-5 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata100_ops, },/* PDC_UDMA_133 */ {
@@ -177,7 +206,7 @@ .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = ATA_UDMA6, /* udma0-6 */ - .port_ops = &pdc2027x_pata_ops, + .port_ops = &pdc2027x_pata133_ops, }, };
Quoted 1 line · Albert Lee
1. For the 100MHz pdc20268 and pdc20270 adapters, rely on the hardware to set the timing registers.
How does the hardware set the timing registers?
Does it snoop the SET FEATURES - XFER MODE command?
Jeff
Quoted 8 lines · Jeff Garzik
Quoted 2 lines
1. For the 100MHz pdc20268 and pdc20270 adapters, rely on the hardware to set the timing registers.
How does the hardware set the timing registers?
Does it snoop the SET FEATURES - XFER MODE command?
Yes.
All chips supported by the pata_pdc2027x driver do that.
The values set by the hardware are assuming PLL running at 100MHz.
So, for 133MHz adatpers, we have to override the values set by hardware by software. For 100Mhz adapters, we can rely on the hardware for the timing registers.
Albert
Jeff Garzik
Appliedapplied