Skip to contentSkip to conversation

power: add AXP313 PMIC support

PATCH In review Andre Przywara 3 participants 12 messages Oct 18, 2023 – Oct 31, 2023

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover power: add AXP313 PMIC support

The X-Powers AXP313 is a small PMIC that is controlled via I2C and provides just three buck converters and three LDOs, plus a power button. It is used on many newer boards using the Allwinner H616 or H618 SoCs.

Mostly all rails need to be always on, since each of them supplies an essential part of the system, consequentially the reset default is to have all of them enabled.
However the voltages need to be adjusted, especially the DRAM rail is typically at 900mV, for instance, which is too low.

This series adds support for the proper DM AXP PMIC driver (patch 3/3), but also adds a small driver to be used in (our non-DM) SPL, to adjust the DRAM voltage before the DRAM initialisation starts (patch 2/3).

This also uses the opportunity to clean up an #ifdef nightmare in our board.c (patch 1/3), which was actually duplicating some dependencies already described in Kconfig.

This is one part of the enablement of many newer boards with the H616/H618 SoC: without the DRAM voltage increased to 1.1V they won't boot.

Cheers,
Andre

Andre Przywara (3):
sunxi: board: simplify early PMIC setup conditions
power: pmic: sunxi: add AXP313 SPL driver
power: regulator: add AXP313 support

 arch/arm/mach-sunxi/pmic_bus.c          |   3 +
 board/sunxi/board.c                     |  35 +++----
 drivers/power/Kconfig                   |  19 +++-
 drivers/power/Makefile                  |   1 +
 drivers/power/axp313.c                  | 134 ++++++++++++++++++++++++
 drivers/power/pmic/axp.c                |   1 +
 drivers/power/regulator/axp_regulator.c |  17 +++
 include/axp_pmic.h                      |   1 +
 8 files changed, 189 insertions(+), 22 deletions(-)
 create mode 100644 drivers/power/axp313.c
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/3 sunxi: board: simplify early PMIC setup conditions

So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.

Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.

To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.

---
 board/sunxi/board.c   | 32 ++++++++++++++------------------
 drivers/power/Kconfig |  2 +-
 2 files changed, 15 insertions(+), 19 deletions(-)
board/sunxi/board.c +14 -18
index ebaa9431984..65d79a02c25 100644
@@ -597,50 +597,46 @@ void sunxi_board_init(void)
 		}
 	}
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_DCDC1_VOLT
 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_DCDC2_VOLT
 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
 	power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
 #endif
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DCDC4_VOLT
 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-#endif
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_ALDO1_VOLT
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO2_VOLT
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
 #endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO3_VOLT
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP209_POWER
+#ifdef CONFIG_AXP_ALDO4_VOLT
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DLDO1_VOLT
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
-#if !defined CONFIG_AXP809_POWER
+#endif
+#ifdef CONFIG_AXP_DLDO3_VOLT
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
 	power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
 #endif
+#ifdef CONFIG_AXP_ELDO1_VOLT
 	power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
 	power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
 	power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
 
-#ifdef CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_FLDO1_VOLT
 	power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
 	power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
 	power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
@@ -649,7 +645,7 @@ void sunxi_board_init(void)
 #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
-#endif
+#endif	/* CONFIG_AXPxxx_POWER */
 	printf("DRAM:");
 	gd->ram_size = sunxi_dram_init();
 	printf(" %d MiB\n", (int)(gd->ram_size >> 20));
drivers/power/Kconfig +1 -1
index 7f3b990d231..83cb31c937a 100644
@@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP305_POWER
+	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP305_POWER
 	default 1250 if AXP152_POWER
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I
Signature · 1 line
2.25.1
maintainer
#2 lore raw

Re: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

Quoted 103 lines · CEST Andre Przywara

So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.

Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.

To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.

---
 board/sunxi/board.c   | 32 ++++++++++++++------------------
 drivers/power/Kconfig |  2 +-
 2 files changed, 15 insertions(+), 19 deletions(-)
board/sunxi/board.c +14 -18
index ebaa9431984..65d79a02c25 100644
@@ -597,50 +597,46 @@ void sunxi_board_init(void)
 		}
 	}
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_DCDC1_VOLT
 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_DCDC2_VOLT
 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
 	power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
 #endif
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DCDC4_VOLT
 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-#endif
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_ALDO1_VOLT
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO2_VOLT
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
 #endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO3_VOLT
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP209_POWER
+#ifdef CONFIG_AXP_ALDO4_VOLT
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DLDO1_VOLT
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
-#if !defined CONFIG_AXP809_POWER
+#endif
+#ifdef CONFIG_AXP_DLDO3_VOLT
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
 	power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
 #endif
+#ifdef CONFIG_AXP_ELDO1_VOLT
 	power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
 	power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
 	power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
 
-#ifdef CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_FLDO1_VOLT
 	power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
 	power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
 	power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
@@ -649,7 +645,7 @@ void sunxi_board_init(void)
 #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
-#endif
+#endif	/* CONFIG_AXPxxx_POWER */
 	printf("DRAM:");
 	gd->ram_size = sunxi_dram_init();
 	printf(" %d MiB\n", (int)(gd->ram_size >> 20));
drivers/power/Kconfig +0 -0
index 7f3b990d231..83cb31c937a 100644

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 183

Quoted 4 lines
drivers/power/Kconfig +0 -1
@@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || 

AXP818_POWER ||

Quoted 1 line

AXP305_POWER + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER

||

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 186

Quoted 3 lines

AXP305_POWER default 1250 if AXP152_POWER

drivers/power/Kconfig +0 -0
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I

This patch is great, but this last change doesn't seem to be directly connected?

Best regards,
Jernej

#3 lore raw

Re: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

Quoted 109 lines · On Sat, 21 Oct 2023 08:34:06 +0200 Jernej Škrabec <[email protected]>…
Quoted 103 lines · CEST Andre Przywara

So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.

Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.

To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.

---
 board/sunxi/board.c   | 32 ++++++++++++++------------------
 drivers/power/Kconfig |  2 +-
 2 files changed, 15 insertions(+), 19 deletions(-)
board/sunxi/board.c +14 -18
index ebaa9431984..65d79a02c25 100644
@@ -597,50 +597,46 @@ void sunxi_board_init(void)
 		}
 	}
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_DCDC1_VOLT
 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_DCDC2_VOLT
 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
 	power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
 #endif
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DCDC4_VOLT
 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-#endif
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_ALDO1_VOLT
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO2_VOLT
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
 #endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO3_VOLT
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP209_POWER
+#ifdef CONFIG_AXP_ALDO4_VOLT
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DLDO1_VOLT
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
-#if !defined CONFIG_AXP809_POWER
+#endif
+#ifdef CONFIG_AXP_DLDO3_VOLT
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
 	power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
 #endif
+#ifdef CONFIG_AXP_ELDO1_VOLT
 	power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
 	power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
 	power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
 
-#ifdef CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_FLDO1_VOLT
 	power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
 	power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
 	power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
@@ -649,7 +645,7 @@ void sunxi_board_init(void)
 #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
-#endif
+#endif	/* CONFIG_AXPxxx_POWER */
 	printf("DRAM:");
 	gd->ram_size = sunxi_dram_init();
 	printf(" %d MiB\n", (int)(gd->ram_size >> 20));
drivers/power/Kconfig +0 -0
index 7f3b990d231..83cb31c937a 100644

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 183

Quoted 4 lines
drivers/power/Kconfig +0 -1
@@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER ||   

AXP818_POWER ||

Quoted 8 lines
Quoted 1 line

AXP305_POWER + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER

||

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 186

Quoted 3 lines

AXP305_POWER default 1250 if AXP152_POWER

drivers/power/Kconfig +0 -0
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I  

This patch is great, but this last change doesn't seem to be directly connected?

It is an existing bug: there is no axp_set_dcdc4() for the AXP818, but since the AXP818 is not included in the guards at the calling site in board.c above, we didn't notice.
So without this change, all A83T boards (the only ones using AXP818) would fail compilation.
I just forgot to mention it in the commit message, will add it.

Cheers,
Andre

#4 lore raw

RE: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

Hi,

Quoted 130 lines

-----Original Message-----
From: Andre Przywara <[email protected]>
Sent: Sunday, October 22, 2023 6:19 AM
To: Jernej Škrabec <[email protected]>
Cc: Jagan Teki <[email protected]>; Jaehoon Chung <[email protected]>; Samuel Holland <[email protected]>; SASANO Takayoshi <[email protected]>; Mikhail Kalashnikov <[email protected]>; Piotr Oniszczuk <[email protected]>; [email protected]; [email protected]
Subject: Re: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

Quoted 109 lines · On Sat, 21 Oct 2023 08:34:06 +0200 Jernej Škrabec <[email protected]>…
Quoted 103 lines · CEST Andre Przywara

So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.

Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.

To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.

---
 board/sunxi/board.c   | 32 ++++++++++++++------------------
 drivers/power/Kconfig |  2 +-
 2 files changed, 15 insertions(+), 19 deletions(-)
board/sunxi/board.c +14 -18
index ebaa9431984..65d79a02c25 100644
@@ -597,50 +597,46 @@ void sunxi_board_init(void)
 		}
 	}
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_DCDC1_VOLT
 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_DCDC2_VOLT
 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
 	power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
 #endif
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DCDC4_VOLT
 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-#endif
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_ALDO1_VOLT
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO2_VOLT
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
 #endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO3_VOLT
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP209_POWER
+#ifdef CONFIG_AXP_ALDO4_VOLT
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DLDO1_VOLT
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
-#if !defined CONFIG_AXP809_POWER
+#endif
+#ifdef CONFIG_AXP_DLDO3_VOLT
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
 	power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
 #endif
+#ifdef CONFIG_AXP_ELDO1_VOLT
 	power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
 	power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
 	power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
 
-#ifdef CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_FLDO1_VOLT
 	power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
 	power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
 	power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
@@ -649,7 +645,7 @@ void sunxi_board_init(void)
 #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
-#endif
+#endif	/* CONFIG_AXPxxx_POWER */
 	printf("DRAM:");
 	gd->ram_size = sunxi_dram_init();
 	printf(" %d MiB\n", (int)(gd->ram_size >> 20));
drivers/power/Kconfig +0 -0
index 7f3b990d231..83cb31c937a 100644

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 183

Quoted 4 lines
drivers/power/Kconfig +0 -1
@@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER ||

AXP818_POWER ||

Quoted 8 lines
Quoted 1 line

AXP305_POWER + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER

||

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 186

Quoted 3 lines

AXP305_POWER default 1250 if AXP152_POWER

drivers/power/Kconfig +0 -0
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I

This patch is great, but this last change doesn't seem to be directly connected?

Quoted 6 lines

It is an existing bug: there is no axp_set_dcdc4() for the AXP818, but since the AXP818 is not included in the guards at the calling site in board.c above, we didn't notice.
So without this change, all A83T boards (the only ones using AXP818) would fail compilation.
I just forgot to mention it in the commit message, will add it.

Will you resend this patch after updating the commit message?

Best Regards,
Jaehoon Chung

Quoted 3 lines

Cheers,
Andre

#5 lore raw

Re: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

On Tue, 31 Oct 2023 15:42:54 +0900
"Jaehoon Chung" <[email protected]> wrote:

Hi Jaehoon,

Quoted 132 lines

Hi,

Quoted 130 lines

-----Original Message-----
From: Andre Przywara <[email protected]>
Sent: Sunday, October 22, 2023 6:19 AM
To: Jernej Škrabec <[email protected]>
Cc: Jagan Teki <[email protected]>; Jaehoon Chung <[email protected]>; Samuel Holland <[email protected]>; SASANO Takayoshi <[email protected]>; Mikhail Kalashnikov <[email protected]>; Piotr Oniszczuk <[email protected]>; [email protected]; [email protected]
Subject: Re: [PATCH 1/3] sunxi: board: simplify early PMIC setup conditions

Quoted 117 lines · On Sat, 21 Oct 2023 08:34:06 +0200 Jernej Škrabec <[email protected]>…
Quoted 103 lines · CEST Andre Przywara

So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend.

Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards.

To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter.

---
 board/sunxi/board.c   | 32 ++++++++++++++------------------
 drivers/power/Kconfig |  2 +-
 2 files changed, 15 insertions(+), 19 deletions(-)
board/sunxi/board.c +14 -18
index ebaa9431984..65d79a02c25 100644
@@ -597,50 +597,46 @@ void sunxi_board_init(void)
 		}
 	}
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_DCDC1_VOLT
 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_DCDC2_VOLT
 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
 	power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
 #endif
-#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DCDC4_VOLT
 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
 #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-#endif
 
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
-	defined CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_ALDO1_VOLT
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#if !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO2_VOLT
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
 #endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP305_POWER)
+#ifdef CONFIG_AXP_ALDO3_VOLT
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
-#ifdef CONFIG_AXP209_POWER
+#ifdef CONFIG_AXP_ALDO4_VOLT
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
-	defined(CONFIG_AXP818_POWER)
+#ifdef CONFIG_AXP_DLDO1_VOLT
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
-#if !defined CONFIG_AXP809_POWER
+#endif
+#ifdef CONFIG_AXP_DLDO3_VOLT
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
 	power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
 #endif
+#ifdef CONFIG_AXP_ELDO1_VOLT
 	power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
 	power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
 	power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
 #endif
 
-#ifdef CONFIG_AXP818_POWER
+#ifdef CONFIG_AXP_FLDO1_VOLT
 	power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
 	power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
 	power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
@@ -649,7 +645,7 @@ void sunxi_board_init(void)
 #if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
 #endif
-#endif
+#endif	/* CONFIG_AXPxxx_POWER */
 	printf("DRAM:");
 	gd->ram_size = sunxi_dram_init();
 	printf(" %d MiB\n", (int)(gd->ram_size >> 20));
drivers/power/Kconfig +0 -0
index 7f3b990d231..83cb31c937a 100644

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 183

Quoted 4 lines
drivers/power/Kconfig +0 -1
@@ -180,7 +180,7 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER ||  

AXP818_POWER ||

Quoted 1 line

AXP305_POWER + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER

||

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 186

Quoted 3 lines

AXP305_POWER default 1250 if AXP152_POWER

drivers/power/Kconfig +0 -0
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I  

This patch is great, but this last change doesn't seem to be directly connected?

Quoted 8 lines
Quoted 6 lines

It is an existing bug: there is no axp_set_dcdc4() for the AXP818, but since the AXP818 is not included in the guards at the calling site in board.c above, we didn't notice.
So without this change, all A83T boards (the only ones using AXP818) would fail compilation.
I just forgot to mention it in the commit message, will add it.

Will you resend this patch after updating the commit message?

Well, I was actually thinking of merging it straight away (with the updated commit message), since I think that plus a tiny typo were the only changes requested in that series.
Unless there is more from your side?

Cheers,
Andre

#6 lore raw

PATCH 2/3 power: pmic: sunxi: add AXP313 SPL driver

In reply to Andre Przywara

On boards using the AXP313 PMIC, the DRAM rail is often not setup correctly at reset time, so we have to program the PMIC very early in the SPL, before running the DRAM initialisation.

Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.

---
 arch/arm/mach-sunxi/pmic_bus.c |   3 +
 board/sunxi/board.c            |   3 +-
 drivers/power/Kconfig          |  17 ++++-
 drivers/power/Makefile         |   1 +
 drivers/power/axp313.c         | 134 +++++++++++++++++++++++++++++++++
 5 files changed, 155 insertions(+), 3 deletions(-)
 create mode 100644 drivers/power/axp313.c
arch/arm/mach-sunxi/pmic_bus.c +3 -0
index c0908406370..8e7625fe057 100644
@@ -22,6 +22,7 @@
 #define AXP209_I2C_ADDR			0x34
 
 #define AXP305_I2C_ADDR			0x36
+#define AXP313_I2C_ADDR			0x36
 
 #define AXP221_CHIP_ADDR		0x68
 
@@ -34,6 +35,8 @@ static int pmic_i2c_address(void)
 		return AXP152_I2C_ADDR;
 	if (IS_ENABLED(CONFIG_AXP305_POWER))
 		return AXP305_I2C_ADDR;
+	if (IS_ENABLED(CONFIG_AXP313_POWER))
+		return AXP313_I2C_ADDR;
 
 	/* Other AXP2xx and AXP8xx variants */
 	return AXP209_I2C_ADDR;
board/sunxi/board.c +2 -1
index 65d79a02c25..39b0ad73a9c 100644
@@ -584,7 +584,8 @@ void sunxi_board_init(void)
 
 #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
 	defined CONFIG_AXP221_POWER || defined CONFIG_AXP305_POWER || \
-	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER || \
+	defined CONFIG_AXP313_POWER
 	power_failed = axp_init();
 
 	if (IS_ENABLED(CONFIG_AXP_DISABLE_BOOT_ON_POWERON) && !power_failed) {
drivers/power/Kconfig +15 -2
index 83cb31c937a..a9117d215eb 100644
@@ -101,6 +101,15 @@ config AXP305_POWER
 	Select this to enable support for the axp305 pmic found on most
 	H616 boards.
 
+config AXP313_POWER
+	bool "axp311 pmic support"
+	depends on MACH_SUN50I_H616
+	select AXP_PMIC_BUS
+	select CMD_POWEROFF
+	---help---
+	Select this to enable support for the AXP313 PMIC found on some
+	H616 boards.
+
 config AXP809_POWER
 	bool "axp809 pmic support"
 	depends on MACH_SUN9I
@@ -143,9 +152,10 @@ config AXP_DCDC1_VOLT
 
 config AXP_DCDC2_VOLT
 	int "axp pmic dcdc2 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER
 	default 900 if AXP818_POWER
 	default 1400 if AXP152_POWER || AXP209_POWER
+	default 1000 if AXP313_POWER
 	default 1200 if MACH_SUN6I
 	default 1100 if MACH_SUN8I
 	default 0 if MACH_SUN9I
@@ -158,13 +168,15 @@ config AXP_DCDC2_VOLT
 	On A80 boards dcdc2 powers the GPU and can be left off.
 	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
+	On boards using the AXP313 it's often VDD-CPU.
 
 config AXP_DCDC3_VOLT
 	int "axp pmic dcdc3 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER
 	default 900 if AXP809_POWER || AXP818_POWER
 	default 1500 if AXP152_POWER
 	default 1250 if AXP209_POWER
+	default 1100 if AXP313_POWER
 	default 1100 if MACH_SUN8I_R40
 	default 1200 if MACH_SUN6I || MACH_SUN8I
 	---help---
@@ -177,6 +189,7 @@ config AXP_DCDC3_VOLT
 	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
 	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
+	On boards using the AXP313 it's often VDD-DRAM and should be 1.1V for LPDDR4.
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
drivers/power/Makefile +1 -0
index ba64b2c5938..c7ee4595fc8 100644
@@ -12,6 +12,7 @@ obj-$(CONFIG_AXP152_POWER)	+= axp152.o
 obj-$(CONFIG_AXP209_POWER)	+= axp209.o
 obj-$(CONFIG_AXP221_POWER)	+= axp221.o
 obj-$(CONFIG_AXP305_POWER)	+= axp305.o
+obj-$(CONFIG_AXP313_POWER)	+= axp313.o
 obj-$(CONFIG_AXP809_POWER)	+= axp809.o
 obj-$(CONFIG_AXP818_POWER)	+= axp818.o
 obj-$(CONFIG_EXYNOS_TMU)	+= exynos-tmu.o
drivers/power/axp313.c new file +134 -0

134 lines not on this page · raw message

Signature · 1 line
2.25.1
maintainer Acked-by on v1 2/3
#7 lore raw

Re: [PATCH 2/3] power: pmic: sunxi: add AXP313 SPL driver

Quoted 43 lines · CEST Andre Przywara

On boards using the AXP313 PMIC, the DRAM rail is often not setup correctly at reset time, so we have to program the PMIC very early in the SPL, before running the DRAM initialisation.

Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.

---
 arch/arm/mach-sunxi/pmic_bus.c |   3 +
 board/sunxi/board.c            |   3 +-
 drivers/power/Kconfig          |  17 ++++-
 drivers/power/Makefile         |   1 +
 drivers/power/axp313.c         | 134 +++++++++++++++++++++++++++++++++
 5 files changed, 155 insertions(+), 3 deletions(-)
 create mode 100644 drivers/power/axp313.c
arch/arm/mach-sunxi/pmic_bus.c +3 -0
index c0908406370..8e7625fe057 100644
@@ -22,6 +22,7 @@
 #define AXP209_I2C_ADDR			0x34
 
 #define AXP305_I2C_ADDR			0x36
+#define AXP313_I2C_ADDR			0x36
 
 #define AXP221_CHIP_ADDR		0x68
 
@@ -34,6 +35,8 @@ static int pmic_i2c_address(void)
 		return AXP152_I2C_ADDR;
 	if (IS_ENABLED(CONFIG_AXP305_POWER))
 		return AXP305_I2C_ADDR;
+	if (IS_ENABLED(CONFIG_AXP313_POWER))
+		return AXP313_I2C_ADDR;
 
 	/* Other AXP2xx and AXP8xx variants */
 	return AXP209_I2C_ADDR;
board/sunxi/board.c +0 -0
index 65d79a02c25..39b0ad73a9c 100644

board/sunxi/board.c void sunxi_board_init(void) · line 591

Quoted 9 lines
board/sunxi/board.c +2 -1
@@ -584,7 +584,8 @@ void sunxi_board_init(void)
 
 #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
 	defined CONFIG_AXP221_POWER || defined CONFIG_AXP305_POWER || \
-	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+	defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER || \
+	defined CONFIG_AXP313_POWER
 	power_failed = axp_init();
 
 	if (IS_ENABLED(CONFIG_AXP_DISABLE_BOOT_ON_POWERON) && !

power_failed) {

drivers/power/Kconfig config AXP305_POWER · line 105

Quoted 10 lines
drivers/power/Kconfig +2 -0
index 83cb31c937a..a9117d215eb 100644
@@ -101,6 +101,15 @@ config AXP305_POWER
 	Select this to enable support for the axp305 pmic found on most
 	H616 boards.
 
+config AXP313_POWER
+	bool "axp311 pmic support"

Typo: axp311 -> axp313

Other than that, it looks good. I can't test it since I don't have any hardware with such PMIC.

So FWIW:

Best regards,
Jernej

Quoted 11 lines
drivers/power/Kconfig +7 -0
+	depends on MACH_SUN50I_H616
+	select AXP_PMIC_BUS
+	select CMD_POWEROFF
+	---help---
+	Select this to enable support for the AXP313 PMIC found on some
+	H616 boards.
+
 config AXP809_POWER
 	bool "axp809 pmic support"
 	depends on MACH_SUN9I

drivers/power/Kconfig config AXP_DCDC1_VOLT · line 146

Quoted 4 lines
drivers/power/Kconfig +0 -1
@@ -143,9 +152,10 @@ config AXP_DCDC1_VOLT
 
 config AXP_DCDC2_VOLT
 	int "axp pmic dcdc2 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || 

AXP809_POWER ||

Quoted 1 line

AXP818_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER

||
> AXP809_POWER || AXP818_POWER || AXP313_POWER default 900 if AXP818_POWER
>  	default 1400 if AXP152_POWER || AXP209_POWER

drivers/power/Kconfig config AXP_DCDC2_VOLT · line 169

Quoted 7 lines
drivers/power/Kconfig +1 -0
+	default 1000 if AXP313_POWER
 	default 1200 if MACH_SUN6I
 	default 1100 if MACH_SUN8I
 	default 0 if MACH_SUN9I
@@ -158,13 +168,15 @@ config AXP_DCDC2_VOLT
 	On A80 boards dcdc2 powers the GPU and can be left off.
 	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 

0.9V.

drivers/power/Kconfig config AXP_DCDC2_VOLT

Quoted 6 lines
drivers/power/Kconfig +1 -1
 	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
+	On boards using the AXP313 it's often VDD-CPU.
 
 config AXP_DCDC3_VOLT
 	int "axp pmic dcdc3 voltage"
-	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || 

AXP809_POWER ||

Quoted 1 line

AXP818_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER

||
> AXP809_POWER || AXP818_POWER || AXP313_POWER default 900 if AXP809_POWER ||

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 189

Quoted 9 lines

AXP818_POWER

drivers/power/Kconfig +1 -0
 	default 1500 if AXP152_POWER
 	default 1250 if AXP209_POWER
+	default 1100 if AXP313_POWER
 	default 1100 if MACH_SUN8I_R40
 	default 1200 if MACH_SUN6I || MACH_SUN8I
 	---help---
@@ -177,6 +189,7 @@ config AXP_DCDC3_VOLT
 	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 

0.9V.

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 190

Quoted 1 line
drivers/power/Kconfig +0 -0
 	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 

0.9V.

drivers/power/Kconfig config AXP_DCDC3_VOLT · line 192

Quoted 2 lines
drivers/power/Kconfig +1 -0
 	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
+	On boards using the AXP313 it's often VDD-DRAM and should be 1.1V 

for

Quoted 83 lines

LPDDR4.

config AXP_DCDC4_VOLT

drivers/power/Kconfig +0 -0
 	int "axp pmic dcdc4 voltage"
drivers/power/Makefile +1 -0
index ba64b2c5938..c7ee4595fc8 100644
@@ -12,6 +12,7 @@ obj-$(CONFIG_AXP152_POWER)	+= axp152.o
 obj-$(CONFIG_AXP209_POWER)	+= axp209.o
 obj-$(CONFIG_AXP221_POWER)	+= axp221.o
 obj-$(CONFIG_AXP305_POWER)	+= axp305.o
+obj-$(CONFIG_AXP313_POWER)	+= axp313.o
 obj-$(CONFIG_AXP809_POWER)	+= axp809.o
 obj-$(CONFIG_AXP818_POWER)	+= axp818.o
 obj-$(CONFIG_EXYNOS_TMU)	+= exynos-tmu.o
drivers/power/axp313.c new file +61 -0
new file mode 100644
index 00000000000..bbc9e911115
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AXP313(a) driver
+ *
+ * (C) Copyright 2023 Arm Ltd.
+ *
+ * Based on axp305.c
+ * (C) Copyright 2020 Jernej Skrabec <[email protected]>
+ * (C) Copyright 2014 Hans de Goede <[email protected]>
+ * (C) Copyright 2013 Oliver Schinagl <[email protected]>
+ */
+
+#include <common.h>
+#include <command.h>
+#include <errno.h>
+#include <asm/arch/pmic_bus.h>
+#include <axp_pmic.h>
+
+enum axp313_reg {
+	AXP313_CHIP_VERSION	= 0x03,
+	AXP313_OUTPUT_CTRL	= 0x10,
+	AXP313_DCDC1_CTRL	= 0x13,
+	AXP313_SHUTDOWN		= 0x1a,
+};
+
+#define AXP313_CHIP_VERSION_MASK	0xcf
+#define AXP313_CHIP_VERSION_AXP1530	0x48
+#define AXP313_CHIP_VERSION_AXP313A	0x4b
+#define AXP313_CHIP_VERSION_AXP313B	0x4c
+
+#define AXP313_DCDC_SPLIT_OFFSET	71
+#define AXP313_DCDC_SPLIT_MVOLT		1200
+
+#define AXP313_POWEROFF			BIT(7)
+
+static u8 mvolt_to_cfg(int mvolt, int min, int max, int div)
+{
+	if (mvolt < min)
+		mvolt = min;
+	else if (mvolt > max)
+		mvolt = max;
+
+	return (mvolt - min) / div;
+}
+
+static int axp_set_dcdc(int dcdc_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg, enable_mask = 1U << (dcdc_num - 1);
+	int volt_reg = AXP313_DCDC1_CTRL + dcdc_num - 1;
+	int max_mV;
+
+	switch (dcdc_num) {
+	case 1:
+	case 2:
+		max_mV	= 1540;
+		break;
+	case 3:
+		/*
+		 * The manual defines a different split point, but tests
+		 * show that it's the same 1200mV as for DCDC1/2.

drivers/power/axp313.c line 71

Quoted 10 lines
drivers/power/axp313.c new file +10 -0
+		 */
+		max_mV	= 1840;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (mvolt > AXP313_DCDC_SPLIT_MVOLT)
+		cfg = AXP313_DCDC_SPLIT_OFFSET + mvolt_to_cfg(mvolt,
+				AXP313_DCDC_SPLIT_MVOLT + 20, 

max_mV, 20);

drivers/power/axp313.c line 73

Quoted 2 lines
drivers/power/axp313.c new file +2 -0
+	else
+		cfg = mvolt_to_cfg(mvolt, 500, AXP313_DCDC_SPLIT_MVOLT, 

10);

drivers/power/axp313.c

Quoted 3 lines
drivers/power/axp313.c new file +3 -0
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP313_OUTPUT_CTRL, 

enable_mask);

drivers/power/axp313.c line 78

Quoted 2 lines
drivers/power/axp313.c new file +2 -0
+
+	debug("DCDC%d: writing 0x%x to reg 0x%x\n", dcdc_num, cfg, 

volt_reg);

Quoted 56 lines
drivers/power/axp313.c new file +45 -0
+	ret = pmic_bus_write(volt_reg, cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP313_OUTPUT_CTRL, enable_mask);
+}
+
+int axp_set_dcdc2(unsigned int mvolt)
+{
+	return axp_set_dcdc(2, mvolt);
+}
+
+int axp_set_dcdc3(unsigned int mvolt)
+{
+	return axp_set_dcdc(3, mvolt);
+}
+
+int axp_init(void)
+{
+	u8 axp_chip_id;
+	int ret;
+
+	ret = pmic_bus_init();
+	if (ret)
+		return ret;
+
+	ret = pmic_bus_read(AXP313_CHIP_VERSION, &axp_chip_id);
+	if (ret)
+		return ret;
+
+	axp_chip_id &= AXP313_CHIP_VERSION_MASK;
+	switch (axp_chip_id) {
+	case AXP313_CHIP_VERSION_AXP1530:
+	case AXP313_CHIP_VERSION_AXP313A:
+	case AXP313_CHIP_VERSION_AXP313B:
+		break;
+	default:
+		debug("unknown PMIC: 0x%x\n", axp_chip_id);
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+#if !CONFIG_IS_ENABLED(ARM_PSCI_FW) &&

!IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF) +int do_poweroff(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) +{

drivers/power/axp313.c new file +9 -0
+	pmic_bus_write(AXP313_SHUTDOWN, AXP313_POWEROFF);
+
+	/* infinite loop during shutdown */
+	while (1) {}
+
+	/* not reached */
+	return 0;
+}
+#endif
#8 lore raw

PATCH 3/3 power: regulator: add AXP313 support

In reply to Andre Przywara

The X-Powers AXP313a is a small PMIC with just three buck converters and three LDOs, one of which is actually fixed (so not modelled here).

Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.

---
 drivers/power/pmic/axp.c                |  1 +
 drivers/power/regulator/axp_regulator.c | 17 +++++++++++++++++
 include/axp_pmic.h                      |  1 +
 3 files changed, 19 insertions(+)
drivers/power/pmic/axp.c +1 -0
index 025dac24f28..0e1e45fba74 100644
@@ -87,6 +87,7 @@ static const struct udevice_id axp_pmic_ids[] = {
 	{ .compatible = "x-powers,axp209", .data = AXP209_ID },
 	{ .compatible = "x-powers,axp221", .data = AXP221_ID },
 	{ .compatible = "x-powers,axp223", .data = AXP223_ID },
+	{ .compatible = "x-powers,axp313a", .data = AXP313_ID },
 	{ .compatible = "x-powers,axp803", .data = AXP803_ID },
 	{ .compatible = "x-powers,axp806", .data = AXP806_ID },
 	{ .compatible = "x-powers,axp809", .data = AXP809_ID },
drivers/power/regulator/axp_regulator.c +17 -0
index 02f320eac1e..d27e09538e0 100644
@@ -173,6 +173,22 @@ static const struct axp_regulator_plat axp22x_regulators[] = {
 	{ }
 };
 
+/*
+ * The "dcdc1" regulator has another range, beyond 1.54V up to 3.4V, in
+ * steps of 100mV. We cannot model this easily, but also don't need that,
+ * since it's typically only used for ~1.1V anyway, so just ignore it.
+ * Also the DCDC3 regulator is described wrongly in the (available) manual,
+ * experiments show that the split point is at 1200mV, as for DCDC1/2.
+ */
+static const struct axp_regulator_plat axp313_regulators[] = {
+	{ "dcdc1", 0x10, BIT(0), 0x13, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc2", 0x10, BIT(1), 0x14, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc3", 0x10, BIT(2), 0x15, 0x7f,  500, 1840,  10, 70 },
+	{ "aldo1", 0x10, BIT(3), 0x16, 0x1f,  500, 3500, 100, NA },
+	{ "dldo1", 0x10, BIT(4), 0x17, 0x1f,  500, 3500, 100, NA },
+	{ }
+};
+
 static const struct axp_regulator_plat axp803_regulators[] = {
 	{ "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
 	{ "dcdc2", 0x10, BIT(1), 0x21, 0x7f,  500, 1300,  10, 70 },
@@ -274,6 +290,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = {
 	[AXP209_ID]	= axp20x_regulators,
 	[AXP221_ID]	= axp22x_regulators,
 	[AXP223_ID]	= axp22x_regulators,
+	[AXP313_ID]	= axp313_regulators,
 	[AXP803_ID]	= axp803_regulators,
 	[AXP806_ID]	= axp806_regulators,
 	[AXP809_ID]	= axp809_regulators,
include/axp_pmic.h +1 -0
index 4ac64865831..aabafc8501b 100644
@@ -32,6 +32,7 @@ enum {
 	AXP209_ID,
 	AXP221_ID,
 	AXP223_ID,
+	AXP313_ID,
 	AXP803_ID,
 	AXP806_ID,
 	AXP809_ID,
Signature · 1 line
2.25.1
maintainer
#9 lore raw

Re: [PATCH 3/3] power: regulator: add AXP313 support

Quoted 31 lines · CEST Andre Przywara

The X-Powers AXP313a is a small PMIC with just three buck converters and three LDOs, one of which is actually fixed (so not modelled here).

Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.

---
 drivers/power/pmic/axp.c                |  1 +
 drivers/power/regulator/axp_regulator.c | 17 +++++++++++++++++
 include/axp_pmic.h                      |  1 +
 3 files changed, 19 insertions(+)
drivers/power/pmic/axp.c +1 -0
index 025dac24f28..0e1e45fba74 100644
@@ -87,6 +87,7 @@ static const struct udevice_id axp_pmic_ids[] = {
 	{ .compatible = "x-powers,axp209", .data = AXP209_ID },
 	{ .compatible = "x-powers,axp221", .data = AXP221_ID },
 	{ .compatible = "x-powers,axp223", .data = AXP223_ID },
+	{ .compatible = "x-powers,axp313a", .data = AXP313_ID },
 	{ .compatible = "x-powers,axp803", .data = AXP803_ID },
 	{ .compatible = "x-powers,axp806", .data = AXP806_ID },
 	{ .compatible = "x-powers,axp809", .data = AXP809_ID },
(quoted diff) +0 -0

b/drivers/power/regulator/axp_regulator.c index 02f320eac1e..d27e09538e0 100644

drivers/power/regulator/axp_regulator.c static const struct axp_regulator_plat · line 179

Quoted 7 lines
drivers/power/regulator/axp_regulator.c +4 -0
@@ -173,6 +173,22 @@ static const struct axp_regulator_plat
 axp22x_regulators[] = { { }
 };
 
+/*
+ * The "dcdc1" regulator has another range, beyond 1.54V up to 3.4V, in
+ * steps of 100mV. We cannot model this easily, but also don't need that,
+ * since it's typically only used for ~1.1V anyway, so just ignore it.

It can be modelled with look up table, as it's already done for some other regulators?

Best regards,
Jernej

Quoted 35 lines
drivers/power/regulator/axp_regulator.c +12 -0
+ * Also the DCDC3 regulator is described wrongly in the (available) manual,
+ * experiments show that the split point is at 1200mV, as for DCDC1/2. +
 */
+static const struct axp_regulator_plat axp313_regulators[] = {
+	{ "dcdc1", 0x10, BIT(0), 0x13, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc2", 0x10, BIT(1), 0x14, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc3", 0x10, BIT(2), 0x15, 0x7f,  500, 1840,  10, 70 },
+	{ "aldo1", 0x10, BIT(3), 0x16, 0x1f,  500, 3500, 100, NA },
+	{ "dldo1", 0x10, BIT(4), 0x17, 0x1f,  500, 3500, 100, NA },
+	{ }
+};
+
 static const struct axp_regulator_plat axp803_regulators[] = {
 	{ "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
 	{ "dcdc2", 0x10, BIT(1), 0x21, 0x7f,  500, 1300,  10, 70 },
@@ -274,6 +290,7 @@ static const struct axp_regulator_plat *const
 axp_regulators[] = { [AXP209_ID]	= axp20x_regulators,
 	[AXP221_ID]	= axp22x_regulators,
 	[AXP223_ID]	= axp22x_regulators,
+	[AXP313_ID]	= axp313_regulators,
 	[AXP803_ID]	= axp803_regulators,
 	[AXP806_ID]	= axp806_regulators,
 	[AXP809_ID]	= axp809_regulators,
include/axp_pmic.h +1 -0
index 4ac64865831..aabafc8501b 100644
@@ -32,6 +32,7 @@ enum {
 	AXP209_ID,
 	AXP221_ID,
 	AXP223_ID,
+	AXP313_ID,
 	AXP803_ID,
 	AXP806_ID,
 	AXP809_ID,
#10 lore raw

Re: [PATCH 3/3] power: regulator: add AXP313 support

Quoted 35 lines · On Sat, 21 Oct 2023 08:51:09 +0200 Jernej Škrabec <[email protected]>…
Quoted 34 lines · CEST Andre Przywara

The X-Powers AXP313a is a small PMIC with just three buck converters and three LDOs, one of which is actually fixed (so not modelled here).

Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.

---
 drivers/power/pmic/axp.c                |  1 +
 drivers/power/regulator/axp_regulator.c | 17 +++++++++++++++++
 include/axp_pmic.h                      |  1 +
 3 files changed, 19 insertions(+)
drivers/power/pmic/axp.c +1 -0
index 025dac24f28..0e1e45fba74 100644
@@ -87,6 +87,7 @@ static const struct udevice_id axp_pmic_ids[] = {
 	{ .compatible = "x-powers,axp209", .data = AXP209_ID },
 	{ .compatible = "x-powers,axp221", .data = AXP221_ID },
 	{ .compatible = "x-powers,axp223", .data = AXP223_ID },
+	{ .compatible = "x-powers,axp313a", .data = AXP313_ID },
 	{ .compatible = "x-powers,axp803", .data = AXP803_ID },
 	{ .compatible = "x-powers,axp806", .data = AXP806_ID },
 	{ .compatible = "x-powers,axp809", .data = AXP809_ID },
(quoted diff) +0 -0

b/drivers/power/regulator/axp_regulator.c index 02f320eac1e..d27e09538e0 100644

drivers/power/regulator/axp_regulator.c +0 -0
@@ -173,6 +173,22 @@ static const struct axp_regulator_plat
 axp22x_regulators[] = { { }
 };
 
Quoted 7 lines

drivers/power/regulator/axp_regulator.c static const struct axp_regulator_plat axp22x_regulators[] = { · line 179

Quoted 4 lines
drivers/power/regulator/axp_regulator.c +4 -0
+/*
+ * The "dcdc1" regulator has another range, beyond 1.54V up to 3.4V, in
+ * steps of 100mV. We cannot model this easily, but also don't need that,
+ * since it's typically only used for ~1.1V anyway, so just ignore it.  

It can be modelled with look up table, as it's already done for some other regulators?

Theoretically yes, but it would require about 105 entries, that's quite a lot for something we don't need. As mentioned, it's typically VDD_GPU/VDD_SYS, at 0.9V at reset, and no device used in U-Boot directly references this regulator, so I think it wouldn't be used anyways. I doubt that even with a user we ever would go beyond 1.54V. So for the sake of simplicity, I'd like to keep this cut to those two ranges.

Thanks for having a look!

Cheers,
Andre

Quoted 44 lines

Best regards,
Jernej

Quoted 35 lines
drivers/power/regulator/axp_regulator.c +12 -0
+ * Also the DCDC3 regulator is described wrongly in the (available) manual,
+ * experiments show that the split point is at 1200mV, as for DCDC1/2. +
 */
+static const struct axp_regulator_plat axp313_regulators[] = {
+	{ "dcdc1", 0x10, BIT(0), 0x13, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc2", 0x10, BIT(1), 0x14, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc3", 0x10, BIT(2), 0x15, 0x7f,  500, 1840,  10, 70 },
+	{ "aldo1", 0x10, BIT(3), 0x16, 0x1f,  500, 3500, 100, NA },
+	{ "dldo1", 0x10, BIT(4), 0x17, 0x1f,  500, 3500, 100, NA },
+	{ }
+};
+
 static const struct axp_regulator_plat axp803_regulators[] = {
 	{ "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
 	{ "dcdc2", 0x10, BIT(1), 0x21, 0x7f,  500, 1300,  10, 70 },
@@ -274,6 +290,7 @@ static const struct axp_regulator_plat *const
 axp_regulators[] = { [AXP209_ID]	= axp20x_regulators,
 	[AXP221_ID]	= axp22x_regulators,
 	[AXP223_ID]	= axp22x_regulators,
+	[AXP313_ID]	= axp313_regulators,
 	[AXP803_ID]	= axp803_regulators,
 	[AXP806_ID]	= axp806_regulators,
 	[AXP809_ID]	= axp809_regulators,
include/axp_pmic.h +1 -0
index 4ac64865831..aabafc8501b 100644
@@ -32,6 +32,7 @@ enum {
 	AXP209_ID,
 	AXP221_ID,
 	AXP223_ID,
+	AXP313_ID,
 	AXP803_ID,
 	AXP806_ID,
 	AXP809_ID,  
Reviewed-by on v1 3/3
#11 lore raw

Re: [PATCH 3/3] power: regulator: add AXP313 support

In reply to Andre Przywara
Quoted 7 lines · Andre Przywara

The X-Powers AXP313a is a small PMIC with just three buck converters and three LDOs, one of which is actually fixed (so not modelled here).

Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.

Best Regards,
Jaehoon Chung

Quoted 65 lines
---
 drivers/power/pmic/axp.c                |  1 +
 drivers/power/regulator/axp_regulator.c | 17 +++++++++++++++++
 include/axp_pmic.h                      |  1 +
 3 files changed, 19 insertions(+)
drivers/power/pmic/axp.c +1 -0
index 025dac24f28..0e1e45fba74 100644
@@ -87,6 +87,7 @@ static const struct udevice_id axp_pmic_ids[] = {
 	{ .compatible = "x-powers,axp209", .data = AXP209_ID },
 	{ .compatible = "x-powers,axp221", .data = AXP221_ID },
 	{ .compatible = "x-powers,axp223", .data = AXP223_ID },
+	{ .compatible = "x-powers,axp313a", .data = AXP313_ID },
 	{ .compatible = "x-powers,axp803", .data = AXP803_ID },
 	{ .compatible = "x-powers,axp806", .data = AXP806_ID },
 	{ .compatible = "x-powers,axp809", .data = AXP809_ID },
drivers/power/regulator/axp_regulator.c +17 -0
index 02f320eac1e..d27e09538e0 100644
@@ -173,6 +173,22 @@ static const struct axp_regulator_plat axp22x_regulators[] = {
 	{ }
 };
 
+/*
+ * The "dcdc1" regulator has another range, beyond 1.54V up to 3.4V, in
+ * steps of 100mV. We cannot model this easily, but also don't need that,
+ * since it's typically only used for ~1.1V anyway, so just ignore it.
+ * Also the DCDC3 regulator is described wrongly in the (available) manual,
+ * experiments show that the split point is at 1200mV, as for DCDC1/2.
+ */
+static const struct axp_regulator_plat axp313_regulators[] = {
+	{ "dcdc1", 0x10, BIT(0), 0x13, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc2", 0x10, BIT(1), 0x14, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc3", 0x10, BIT(2), 0x15, 0x7f,  500, 1840,  10, 70 },
+	{ "aldo1", 0x10, BIT(3), 0x16, 0x1f,  500, 3500, 100, NA },
+	{ "dldo1", 0x10, BIT(4), 0x17, 0x1f,  500, 3500, 100, NA },
+	{ }
+};
+
 static const struct axp_regulator_plat axp803_regulators[] = {
 	{ "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
 	{ "dcdc2", 0x10, BIT(1), 0x21, 0x7f,  500, 1300,  10, 70 },
@@ -274,6 +290,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = {
 	[AXP209_ID]	= axp20x_regulators,
 	[AXP221_ID]	= axp22x_regulators,
 	[AXP223_ID]	= axp22x_regulators,
+	[AXP313_ID]	= axp313_regulators,
 	[AXP803_ID]	= axp803_regulators,
 	[AXP806_ID]	= axp806_regulators,
 	[AXP809_ID]	= axp809_regulators,
include/axp_pmic.h +1 -0
index 4ac64865831..aabafc8501b 100644
@@ -32,6 +32,7 @@ enum {
 	AXP209_ID,
 	AXP221_ID,
 	AXP223_ID,
+	AXP313_ID,
 	AXP803_ID,
 	AXP806_ID,
 	AXP809_ID,