ASoC: dwc: correct irq clear method
PATCH RESEND 1/1 ASoC: dwc: correct irq clear method
from Designware I2S datasheet, irq is cleared by reading from TOR/ROR registers, rather than by writing into them.
--- sound/soc/dwc/designware_i2s.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
sound/soc/dwc/designware_i2s.c +0 -0
@@ -131,10 +131,10 @@ static inline void i2s_clear_irqs(struct dw_i2s_dev
*dev, u32 stream)
if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
for (i = 0; i < 4; i++)
- i2s_write_reg(dev->i2s_base, TOR(i), 0);
+ i2s_read_reg(dev->i2s_base, TOR(i));
} else {
for (i = 0; i < 4; i++)
- i2s_write_reg(dev->i2s_base, ROR(i), 0);
+ i2s_read_reg(dev->i2s_base, ROR(i));
}
}
Signature · 1 line
1.7.12.4
Mark Brown
maintainerQuoted 2 lines · yitian
from Designware I2S datasheet, irq is cleared by reading from TOR/ROR registers, rather than by writing into them.
This doesn't apply against current code, please check and resend.
Quoted 11 lines
From: linux-arm-kernel
[mailto:linux-arm-kernel-bounces at lists.infradead.org] On Behalf Of Mark Brown
Sent: Thursday, October 1, 2015 2:18 AM
To: yitian <[email protected]>
Cc: alsa-devel at alsa-project.org; wsa at the-dreams.de; linux-kernel at vger.kernel.org; Andrew.Jackson at arm.com; tiwai at suse.com; lgirdwood at gmail.com; perex at perex.cz;
linux-arm-kernel at lists.infradead.org
Subject: Re: [RESEND PATCH 1/1] ASoC: dwc: correct irq clear method
Quoted 5 lines
Quoted 2 lines · yitian
from Designware I2S datasheet, irq is cleared by reading from TOR/ROR registers, rather than by writing into them.
This doesn't apply against current code, please check and resend.
Hi Mark:
Thanks for your comments.
Maybe I misunderstand your meaning. Please correct me.
I synced up to latest kernel branch, the code is the same as what this patch was
generated.
I checked designware I2S spec "version 1.08a June 2014", it specified that the TOR
and ROR registers are read only and reading the last bit will clear tx/rx overrun irq.
Also I have checked this register by writing its last bit, the overrun irq is not cleared.
But if I read the last bit, the overrun irq is cleared. That means the spec is correct.
Can you please let me know what else I should double check? Thanks.
Mark Brown
maintainerQuoted 5 lines · yitian
Quoted 1 line
This doesn't apply against current code, please check and resend.
I synced up to latest kernel branch, the code is the same as what this patch was
generated.
The "latest kernel branch" was neither v4.3-rc1 nor my for-next branch, at least as far as git am was concerned, so I couldn't apply the patch.
Hi Mark:
Quoted 15 lines
From: alsa-devel-bounces at alsa-project.org [mailto:alsa-devel-bounces at alsa-project.org] On Behalf Of Mark Brown
Sent: Thursday, October 1, 2015 6:04 PM
To: yitian <[email protected]>
Cc: alsa-devel at alsa-project.org; wsa at the-dreams.de; linux-kernel at vger.kernel.org; Andrew.Jackson at arm.com; lgirdwood at gmail.com; tiwai at suse.com;
linux-arm-kernel at lists.infradead.org
Subject: Re: [alsa-devel] [RESEND PATCH 1/1] ASoC: dwc: correct irq clear methodQuoted 1 line · yitian
Quoted 1 line
This doesn't apply against current code, please check and resend.
Quoted 8 lines
Quoted 1 line
I synced up to latest kernel branch, the code is the same as what this
patch
Quoted 2 lines
was
generated.The "latest kernel branch" was neither v4.3-rc1 nor my for-next branch, at least as far as git am was concerned, so I couldn't apply the patch.
I am sorry.
I used Linux v4.3-rc3 to generate the patch, and I assumed that was the same as v4.3-rc1.
I generated new patch based on next-20151001, please review it again, thanks.